MODEL: EM6027LW-42C
PRODUCT: Omni Directional Back Electret Condenser Microphone
EDITION: A/2017
TYPE: OMNI DIRECTIONAL BACK ELECTRET CONDENSER MICROPHONE
ELECTRICAL CHARACTERISTICS
Temperature =20±2 °C Humidity=65±5%
parameter
symbol
condition
sensitivity
S
0dB=1V/Pa at 1kHz
output impedance
Z out
current consumption
limits
unit
min
center
max
-45
-42
-39
dB
f=1kHz
2.2
KΩ
IDSS
VCC =2.0V, RL=2.2KΩ
500
µA
signal to noise ratio
S/N
at 1kHz S.P.L=1Pa
(A-Weighted Curve)
decreasing voltage
ΔS
VCC=3.0V to 2.0V
operating voltage
58
1.0
maximum input S.P.L
dimension
dB
-3
dB
10
V
115
dB
Ø6.0 x 2.7mm (LW 25)
TYPICAL FREQUENCY RESPONSE CURVE
FREQUENCY RESPONSE
MICROPHONE RESPONSE TOLERANCE WINDOW
Frequency(Hz)
Lower Limit(dB)
Upper
Limit(dB)
50
-6
+3
100
-3
+3
800
-3
+3
1000
0
0
1200
-3
+3
3000
-3
+8
5000
-3
+8
10000
-8
+8
MEASUREMENT CIRCUIT
RL = 2.2KΩ
Vs = 2.0V
C1 = 10pF
C2 = 33pF
C = 1µF
PAGE 1/6
MODEL: EM6027LW-42C
PRODUCT: Omni Directional Back Electret Condenser Microphone
EDITION: A/2017
TEMPERATURE CONDITIONS
storage temperature range
-40°C ~ +85°C
operation temperature range
-40°C ~ +85°C
Note: Store in electronic warehouse.
RELIABILITY TEST
After each of the following tests, the sensitivity of the microphone should be within ±3dB of initial sensitivity after 3 hours of
conditioning at 20°C .
vibration test
frequency
10Hz ~ 55Hz
amplitude
1.52mm
change of frequency
1 octave/min
2 hours in each of axis
high temperature test
+85°C for 240 hours
low temperature test
-40°C for 240 hours
humidity test
90% ~ 95%RH, +60°C for 240 hours
thermal shocking test
–40°C, 30 minutes
temperature cycles
-40°C
(2h)
+80°C, 30 minutes, repeated 32 cycles
+20°C
(0.5h)
(2h)
+85°C
(0.1h)
(2h)
+20°C
(0.5h)
(2h)
room temperature, 3 hours
-40°C
(0.5h)
(2h) for 5 cycles
packing drop test
height
1.5m
procedure
5 times from each of axis
electrostatic discharge
Tested to IEC61000-4-2 level 3
contact discharge
The microphone shall operate normally after 10 discharges to is 6KV DC and the discharge
network is 150pF & 330Ω.
air discharge
The microphone shall operate normally after 10 discharges to is 8KV DC and the discharge
network is 150pF & 330Ω
IP level
IP67
SOLDERING CONDITION
We suggest using an anti-static welding machine which can control soldering temperature automatically.
Soldering temperature should be controlled at under 320 °C and soldering time for each terminal should be 1~2 seconds.
Microphone should be fixed on the metal block (heat sink)and the heat sink shall contact with MIC tightly.
Microphone may easily be damaged by the static electricity. The countermeasure for eliminating the static electricity shall be by
grounding both the worktable and the operator.
PAGE 2/6
MODEL: EM6027LW-42C
PRODUCT: Omni Directional Back Electret Condenser Microphone
EDITION: A/2017
MEASUREMENT SETUP DRAWING
PRODUCT EXTERNAL VIEW AND DIMENSION
Unit : mm
EXPLODED DRAWING AND MATERIAL TABLE
Name
Material
Quantity
1
Felt
Non-weave cloth
1
2
Case
Al-Mg alloy
1
3
Polarized diaphragm
1
4
Spacer
1
5
Electret back
1
6
Chamber
1
7
Copper ring
1
8
PCB
FR-4
1
9
Chip capacitor
10+33pF
2
10
FET
1
PAGE 3/6
MODEL: EM6027LW-42C
PRODUCT: Omni Directional Back Electret Condenser Microphone
EDITION: A/2017
ACCESSORY DRAWING
PAGE 4/6
MODEL: EM6027LW-42C
PRODUCT: Omni Directional Back Electret Condenser Microphone
EDITION: A/2017
HEAT SINK
SHAPE OF HEAT SINK
SHAPE OF HOLE AT FIXED PART
PAGE 5/6
MODEL: EM6027LW-42C
PRODUCT: Omni Directional Back Electret Condenser Microphone
EDITION: A/2017
PACKING
DIMENSION:(LENGTH*WIDTH *HEIGHT)
ANTI-STATIC BAG : 100mm*100mm*2mm
SMALL BOX : 100mm*100mm*10mm
MIDDLE BOX : 205mm*105mm*50mm
CARTON SIZE : 550mm*230mm*235mm
QUANTITY AND WEIGHT
100PCS/SMALL BOX
1000PCS/MID BOX
20000PCS/CARTON
1PC=0.2g
NET WEIGHT: 4.0kg
GROSS WEIGHT: 8.0kg
X1
100PCS
X10
1000PCS
X20
20000PCS
PAGE 6/6
很抱歉,暂时无法提供与“EM6027LW-42C”相匹配的价格&库存,您可以联系我们找货
免费人工找货