CXA1562S

CXA1560S, CXA1561M/S, CXA1562M/S Dolby∗ B-C Type Noise Reduction System Description The CXA1560 series is a bipolar IC incorporating stereo Dolby B-C type noise reduction (NR) system. Five kinds of device are provided due to the combination of three line output levels and two packages for various applications. A reduction in the number of external parts and small package have been achieved due to the fact that the spectral skewing circuits are all on-chip. Features • Few external parts • Spectral skewing circuit are on-chip • NR ON/OFF, REC/PB, MPX filter ON/OFF switches • Small package (24-pin SOP, 22-pin SDIP) • Low current consumption 13mA Typ. (power supply ±6V) Structure Bipolar silicon monolithic IC Absolute Maximum Ratings (Ta = 25°C) 17 • Supply voltage Vcc – VEE • Operating temperature Topr –40 to +85 • Storage temperature Tstg –65 to +150 • Allowable power dissipation PD 600 (SOP) 1200 (SDIP) CXA1561M CXA1562M 24 pin SOP (Plastic) CXA1560S CXA1561S CXA1562S 22 pin SDIP (Plastic) V °C °C mW mW ∗ This IC is available only to the licensees of Dolby Laboratories Licensing Corporation from whom licensing and applications information may be obtained. ∗ "Dolby" and the double D symbols are trademarks of Dolby Laboratories Licensing Corporation. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E93805B5X-PP Block Diagram and Pin Configuration P13 LINEOUT1 PBIN1 P12 C11 1µ C12 1µ R11 3.3k C13 1µ C14 100n C15 68n C16 1µ P2 VCC MPX Filter PBIN1 LINEIN1 RECOUT1 P14 RECOUT1 MPXIN1 MODE P3 MODE 13 12 LINEIN1 P11 R12 6.8k MPXOUT1 LINEOUT1 VCT TCH1 22 20 21 16 19 18 17 15 14 TCL1 SSK REC AMP VCC VCC C1 10µ MOA HLS HDET LDET LLS Mode Control IREF PBIN2 TCH2 TCL2 LINEIN2 MPXIN2 R1 20k MPX Filter R22 6.8k C21 1µ C22 1µ MPXOUT2 LINEOUT2 R21 3.3k C23 1µ C24 100n C25 68n RECOUT2 C26 1µ P1 VEE PBIN2 P22 CXA1560S, CXA1561M/S, CXA1562M/S Note) This figure shows SDIP package. For SOP package, refer to the Pin Description or Application Circuit. LINEOUT2 P23 RECOUT2 P24 NRSW P5 LINEIN2 P21 NRSW VEE –2– MOA HLS HDET LDET LLS SSK REC AMP 2 3 4 5 6 7 8 9 IREF VEE C2 10µ 1 10 11 CXA1560S, CXA1561M/S, CXA1562M/S Pin Description and Equivalent Circuit Pin No. SOP SDIP VCC Symbol Z: Imp VDC (V) Equivalent circuit Description 1 1 IREF 0 VEE + 1.25V VEE + 1.25V Reference current pin for setting internal filter cut-off frequency VEE VCC 2, 23 2, 21 PB IN 40k VCT Playback input pin Reference level = –30dBm 40K VCT Buffer amplifier input pin to drive multiplex filter Reference level = –19dBm VEE VCC 4, 21 4, 19 MPX IN VCT 62k 3, 22 3, 20 LINE IN 62K VCT Recording input pin Reference level = –25dBm VEE VCC 500 5, 20 5, 18 MPX OUT 0 VCT 8.8k 500 Buffer amplifier output pin to drive multiplex filter Reference level = –15dBm VEE –3– CXA1560S, CXA1561M/S, CXA1562M/S Pin No. SOP SDIP Symbol Z: Imp VDC (V) Equivalent circuit VCC Description 200 6, 19 6, 17 LINE OUT 0 VCT 200 Line output pin VEE VCC 7, 15 7, 16 TCH — VEE + 0.4V 13k 36k Time constant connecting pin for HLS detector 330k VEE VCC 8, 17 8, 15 TCL — VEE + 0.4V 13.5k Time constant connecting pin for LLS detector 480k VEE VCC 200 9, 16 9, 14 REC OUT 0 VCT 200 Recording output pin Reference level = –6dBm VEE –4– CXA1560S, CXA1561M/S, CXA1562M/S Pin No. SOP SDIP Symbol Z: Imp VDC (V) Equivalent circuit VCC 50µA Description 10 10 NRSW — — 50k 22k NR control pin H: C type M: B type L: NR OFF VEE 11 14 11 12 VEE VCC VEE VCC VCC 50µA Dual power supply: VEE Single power supply: GND pin Vcc 15 13 MODE — — 50k 22k MODE control pin H: REC (Filter ON) M: REC (Filter OFF) L: PB VEE 24 22 VCT 0 VCT Dual power supply: GND Single power supply: Vcc/2 –5– CXA1560S, CXA1561M/S, CXA1562M/S Electrical Characteristics Ta = 25°C, Dolby level: –6dBm (= 388mVrms) at REC OUT, VCC = 15V (CXA1560), VCC = 12V (CXA1561), VCC = 9V (CXA1562) Characteristics Operating voltage CXA1560 CXA1561 CXA1562 Current consumption CXA1560 CXA1561 CXA1562 LINE OUT level CXA1560 CXA1561 CXA1562 LINE IN level PB IN level MPX amplifier gain Encode characteristics B type boost (1) (2) (3) (4) C type boost (1) (2) (3) (4) (5) (6) C-R-1 C-R-2 C-R-3 C-R-4 C-R-5 C-R-6 REC REC REC REC REC REC C C C C C C 500 500 2k 2k 5k 10k –60dB –25dB –60dB –25dB –25dB 0dB 14.2 7.2 18.7 5.4 3.5 –5.5 16.2 9.2 20.7 7.4 5.5 –3.5 18.2 11.2 22.7 9.4 7.5 –1.5 dB dB dB dB dB dB B-R-1 B-R-2 B-R-3 B-R-4 REC REC REC REC B B B B 500 5k 10k 10k –25dB –25dB –40dB 0dB 1.4 3.9 9.7 –1.1 2.9 5.4 10.4 0.4 4.4 6.9 11.4 1.9 dB dB dB dB Symbol R/P Measurement conditions∗ NR f (Hz) Other conditions 11.5 8.5 7.2 8.0 8.0 8.0 –1.0 –4.0 –7.0 –27 –32 9.0 — — — 13.2 13.0 12.8 0.0 –3.0 –6.0 –25 –30 10.0 16.0 16.0 16.0 18.0 18.0 18.0 1.0 –2.0 –5.0 –23 –28 11.0 V V V mA mA mA dBm dBm dBm dBm dBm dB Min. Typ. Max. Unit Vopr — — — ICC REC OFF — No Signal Vlout REC OFF 1k Vlin Vpin Gmpx REC OFF PB OFF 1k 1k 1k MPX OFF –6– CXA1560S, CXA1561M/S, CXA1562M/S Characteristics Signal handling CXA1560 CXA1561 CXA1562 Total harmonic distortion 1) NR OFF CXA1560 CXA1561 CXA1562 2) B CXA1560 CXA1561 CXA1562 3) C CXA1560 CXA1561 CXA1562 S/N REC-PB PB-REC REC ch to ch REC OUT offest Voltage (OFF-C type) Symbol R/P Measurement conditions∗ NR f (Hz) Other conditions Min. Typ. Max. Unit Vomax REC OFF 1k THD = 1% 13.5 13.5 13.5 16.0 16.2 16.0 — — — dB dB dB THD (OFF) REC OFF 1k +10dB — — — — — — — — — 60 — — — –100 0.03 0.02 0.02 0.03 0.03 0.04 0.04 0.04 0.05 64 –80 –87 –73 0 0.1 0.1 0.1 0.1 0.1 0.1 0.2 0.2 0.2 — –70 –70 –65 100 % % % % % % % % % dB dB dB dB mV THD (B) REC B 1k +10dB THD (C) SN (CCIR) CT-1 CT-2 CT-3 Voff REC C 1k +10dB Rg = 5Ω (CCIR/ARM) 0dB 0dB 0dB REC C — 1k 1k 1k — PB OFF REC OFF REC OFF REC OFF ↓ C ∗ 0dB means the level which provides the Dolby level to recording output when NR is off. –7– Electrical Characteristics Measurement Circuit S12 R12 6.8k S2-1 C16 1µ S1-1 S11 C11 1µ VMODE 14 13 12 21 20 16 19 18 17 15 C12 1µ R11 3.3k C13 1µ C14 100n C15 68n DC Volt Meter C2 100µ 22 VCT PBIN1 TCH1 TCL1 LINEIN1 MPXIN1 MPXOUT1 LINEOUT1 RECOUT1 MODE VCC VCC PBIN2 MPXOUT2 IREF MPXIN2 TCH2 LINEIN2 LINEOUT2 RECOUT2 NRSW TCL2 GND –8– CXA1560S/A1561S/A1562S 2 3 C21 1µ C22 1µ R21 3.3k C23 1µ C24 100n C25 68n VNRSW R22 6.8k 7 4 8 5 6 9 10 11 C26 1µ S1-2 Audio SG A C1 100µ 1 R1 20k S21 S2-2 S3 CCIR/ARM Filter Audio Analyzer CXA1560S, CXA1561M/S, CXA1562M/S S22 Application Circuit Switchable Processor with Dual Power Supply (CXA1560S/1561S/1562S) LINEIN1 P11 P14 RECOUT1 MPX Filter MPX OFF MPX ON 13 12 R12 6.8k (5%) P13 LINEOUT1 R11 3.3k (5%) PBIN1 P12 C11 1µ C12 1µ C13 1µ C14 100n (10%) 16 15 14 C15 68n (10%) PB C16 1µ P2 VCC 22 20 21 19 18 17 VCC VCT PBIN1 TCH1 TCL1 LINEIN1 MPXIN1 MPXOUT1 PBIN2 IREF LINEIN2 MPXIN2 TCH2 TCL2 MPXOUT2 LINEOUT2 RECOUT2 NRSW VEE –9– CXA1560S/1561S/1562S 3 4 7 8 5 6 9 10 C22 1µ C23 1µ OFF C26 1µ B C24 100n (10%) C25 68n (10%) C MPX Filter R22 6.8k (5%) R21 3.3k (5%) LINEOUT1 RECOUT1 MODE C1 10µ C2 10µ 11 1 2 R1 20k (2%) C21 1µ P1 VEE P24 RECOUT2 P23 LINEOUT2 PBIN2 P22 LINEIN2 P21 CXA1560S, CXA1561M/S, CXA1562M/S Note) Resistor and capacitor tolerances are ±10% and ±20% respectively, unless otherwise specified. Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. Switchable Processor with Dual Power Supply (CXA1561M/1562M) LINEIN1 P11 MPX Filter MPX OFF MPX ON 15 14 13 R12 6.8k (5%) P13 LINEOUT1 R11 3.3k (5%) P14 RECOUT1 PBIN1 P12 C11 1µ C12 1µ C13 1µ C14 100n (10%) 18 17 16 C15 68n (10%) PB C16 1µ P2 VCC 24 23 20 22 21 19 VCC VCT PBIN1 TCH1 TCL1 LINEIN1 MPXIN1 MPXOUT1 MPXOUT2 LINEOUT2 RECOUT2 PBIN2 IREF LINEIN2 MPXIN2 TCH2 TCL2 NRSW VEE N.C. – 10 – CXA1561M/1562M 3 4 7 8 5 6 9 10 11 C22 1µ C23 1µ OFF C26 1µ B C24 100n (10%) C25 68n (10%) C MPX Filter R22 6.8k (5%) R21 3.3k (5%) LINEOUT1 RECOUT1 MODE N.C. C1 10µ C2 10µ 12 1 2 R1 20k (2%) C21 1µ P1 VEE P24 RECOUT2 P23 LINEOUT2 PBIN2 P22 LINEIN2 P21 Note) Resistor and capacitor tolerances are ±10% and ±20% respectively, unless otherwise specified. Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. CXA1560S, CXA1561M/S, CXA1562M/S Switchable Processor with Single Power Supply (CXA1560S/1561S/1562S) LINEIN1 P11 P14 RECOUT1 MPX Filter MPX OFF MPX ON 13 12 P2 VCC R12 6.8k (5%) P13 LINEOUT1 R11 3.3k (5%) PBIN1 P12 C11 1µ C12 1µ C13 1µ C14 100n (10%) 16 15 14 C15 68n (10%) PB C16 1µ 22 20 21 19 18 17 VCT PBIN1 TCH1 TCL1 MODE VCC LINEIN1 MPXIN1 MPXOUT1 CXA1560S/1561S/1562S LINEOUT1 RECOUT1 C1 10µ PBIN2 IREF LINEIN2 MPXIN2 TCH2 TCL2 MPXOUT2 LINEOUT2 1 3 4 7 8 2 5 6 9 RECOUT2 10 NRSW 11 VEE – 11 – C22 1µ C23 1µ OFF C26 1µ B C24 100n (10%) C25 68n (10%) C MPX Filter R22 6.8k (5%) R21 3.3k (5%) C2 47µ R1 20k (2%) C21 1µ P1 GND P24 RECOUT2 P23 LINEOUT2 PBIN2 P22 LINEIN2 P21 Note) Resistor and capacitor tolerances are ±10% and ±20% respectively, unless otherwise specified. CXA1560S, CXA1561M/S, CXA1562M/S Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. Switchable Processor with Single Power Supply (CXA1561M/1562M) LINEIN1 P11 MPX Filter MPX OFF MPX ON 15 14 13 R12 6.8k (5%) P13 LINEOUT1 R11 3.3k (5%) P14 RECOUT1 PBIN1 P12 C11 1µ C12 1µ C13 1µ C14 100n (10%) 18 17 16 C15 68n (10%) PB C16 1µ P2 VCC 24 23 22 20 21 19 VCT VCC PBIN1 TCH1 TCL1 MODE N.C. LINEIN1 MPXIN1 MPXOUT1 CXA1561M/1562M LINEOUT1 RECOUT1 C1 10µ PBIN2 IREF LINEIN2 MPXIN2 TCH2 TCL2 MPXOUT2 LINEOUT2 RECOUT2 NRSW VEE 1 4 7 8 10 2 3 5 6 9 11 N.C. 12 – 12 – C22 1µ C23 1µ OFF C26 1µ B C24 100n (10%) C25 68n (10%) C MPX Filter R22 6.8k (5%) R21 3.3k (5%) C2 47µ R1 20k (2%) C21 1µ P1 GND P24 RECOUT2 P23 LINEOUT2 PBIN2 P22 LINEIN2 P21 Note) Resistor and capacitor tolerances are ±10% and ±20% respectively, unless otherwise specified. Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. CXA1560S, CXA1561M/S, CXA1562M/S CXA1560S, CXA1561M/S, CXA1562M/S Application Note The CXA1560 series is a stereo Dolby B-C type NR IC like the CXA1330 series. Built-in spectral skewing circuit allows smaller package. 1) Power Supply The CXA1560 series is designed to operate on either single or dual power supply. For dual power supply, connect VCT to GND, and VEE to the negative power supply. For single power supply, connect VEE to GND. Vcc/2, generated from the internal circuit, is output to VCT. Connect a by-pass capacitor between this pin and GND. The operating voltage range is ±3.5 to ±8.0V (7.0 to 16V), which satisfies the signal handling of 12dB specified by the Dolby Laboratories. 2) Operation Mode Control The CXA1560 series has built-in electronic switches. The operations are controlled by the DC voltages of NRSW and MODE control pins. Table 1 shows the switching truth tables. For single power supply, VH, VM, and VL correspond to Vcc, Vcc/2 and GND, respectively. For dual power supply, VH, VM and VL correspond to Vcc, GND and VEE, respectively. Refer to “threshold” on the characteristics graph for the thresholds of the control voltages. NRSW and MODE control pins are connected to VCT via a 50kΩ resistor, so when the pin is open, VM condition results. VH NRSW MODE C type MPX ON REC (Encode) VM B type MPX OFF REC (Encode) Table 1 3) Reference level The CXA1560 series Dolby level is –6dBm (388mVrms), and is measured at the recording output pin (REC OUT) in the NR OFF mode. The reference level of the recording input pin (LINE IN), playback input pin (PB IN) and line output pin (LINE OUT) are defined as the levels which provide Dolby level at the recording output pin in NR OFF mode. 4) MPX Filter The CXA1560 series provides an MPX (FM multiplex) filter ON/OFF function. Connect the MPX filter between MPX IN and MPX OUT. In MPX ON mode, the line input signal is fed to the NR processor via the MPX buffer amplifier and MPX filter. In MPX OFF mode, the signal bypasses the buffer amplifier and filter, and is fed directly to the NR processor. The MPX buffer amplifier gain is 10dB. The gain from LINE IN to LINE OUT is 19dB, and from MPX IN to LINE OUT it is 13dB, for a deviation of 6dB. This means that if a filter with insertion loss of 4dB is used, there is no fluctuation between MPX ON and MPX OFF. VL NR OFF PB (Decode) – 13 – CXA1560S, CXA1561M/S, CXA1562M/S Example of Representative Characteristics Quiescent current consumption vs. Supply voltage ICC–Quiescent current consumptionl [mA] Encode Mode 15 16 Current consumption vs. Input level Encode Mode VCC = ±6V 0dB = Dolby Level Bf = 10k Cf = 10k ICC–Current consumption [mA] 15 14 13 12 11 10 14 13 12 11 10 8 4 6 B type NR OFF C type NR OFF Bf = 1k Cf = 1k 8 10 12 14 16 VCC-VEE–Supply voltage [V] –12 –8 –4 0 4 Input level [dB] 8 12 B type encode characteristics 12 10 VCC = ±6V 0dB = Dolby Level –40dB 24 20 C type encode characteristics VCC = ±6V 0dB = Dolby Level –60dB –50dB Encode boost [dB] 8 6 4 2 0 Encode boost [dB] –30dB 16 12 8 4 0 0dB –40dB –20dB –10dB 0dB –30dB –20dB –10dB 100 200 500 1k 2k 5k Frequency [Hz] 10k 20k 100 200 500 1k 2k 5k Frequency [Hz] 10k 20k Signal handling Encode Mode f = 1kHz THD = 1% 0dB = Dolby Level A1562 16 Load characteristics Encode Mode VCC = ±6V THD = 1% f = 1kHz NR OFF Signal handling [dB] A1561 A1560 10 Maximum output level [dBm] 20 14 12 10 8 6 4 0 NR OFF C type 4 6 8 10 12 14 16 VCC-VEE–Supply voltage [V] LINE OUT 200 REC OUT 10k 500 1k 2k 5k Load resistance [Ω] – 14 – CXA1560S, CXA1561M/S, CXA1562M/S NR OFF total harmonic distortion-1 (CXA1561) Encode Mode VCC = ±6.0V 0dB = Dolby Level 0.1 NR OFF total harmonic distortion-2 (CXA1560) Encode Mode f = 1kHz 0dB = Dolby Level 0.1 Distortion [%] f = 100Hz f = 10kHz f = 1kHz Distortion [%] VCC = ±5.5V 0.01 VCC = ±8.0V 0.01 –4 0 4 8 12 16 Output level [dB] 20 –4 0 4 8 12 16 Output level [dB] 20 B type total harmonic distortion-1 (CXA1561) Encode Mode VCC = ±6.0V 0dB = Dolby Level 0.1 f = 100Hz B type total harmonic distortion-2 (CXA1560) Encode Mode f = 1kHz 0dB = Dolby Level 0.1 Distortion [%] Distortion [%] VCC = ±5.5V VCC = ±8.0V 0.01 f = 1kHz 0.01 f = 10kHz –4 0 4 8 12 16 Output level [dB] 20 –4 0 4 8 12 16 Output level [dB] 20 C type total harmonic distortion-1 (CXA1561) Encode Mode VCC = ±6.0V 0dB = Dolby Level C type total harmonic distortion-2 (CXA1560) Encode Mode f = 1kHz 0dB = Dolby Level 1.0 1.0 Distortion [%] f = 10kHz Distortion [%] 0.1 f = 100Hz VCC = ±5.5V 0.1 VCC = ±8.0V f = 1kHz 0.01 –4 0 4 8 12 16 Output level [dB] 20 0.01 –4 0 4 8 12 16 Output level [dB] 20 – 15 – CXA1560S, CXA1561M/S, CXA1562M/S NR OFF total harmonic distortion-3 (CXA1561) Encode Mode f = 1kHz 0dB = Dolby Level 0.1 NR OFF total harmonic distortion-4 (CXA1562) Encode Mode f = 1kHz 0dB = Dolby Level 0.1 Distortion [%] Distortion [%] VCC = ±3.5V VCC = ±4.0V 0.01 VCC = ±8.0V 0.01 VCC = ±8.0V –4 0 4 8 12 16 Output level [dB] 20 –4 0 4 8 12 16 Output level [dB] 20 B type total harmonic distortion-3 (CXA1561) Encode Mode f = 1kHz 0dB = Dolby Level 0.1 B type total harmonic distortion-4 (CXA1562) Encode Mode f = 1kHz 0dB = Dolby Level 0.1 Distortion [%] VCC = ±4.0V VCC = ±8.0V 0.01 Distortion [%] VCC = ±3.5V VCC = ±8.0V 0.01 –4 0 4 8 12 16 Output level [dB] 20 –4 0 4 8 12 16 Output level [dB] 20 C type total harmonic distortion-3 (CXA1561) Encode Mode f = 1kHz 0dB = Dolby Level C type total harmonic distortion-4 (CXA1562) Encode Mode f = 1kHz 0dB = Dolby Level VCC = ±3.5V 1.0 1.0 Distortion [%] VCC = ±4.0V 0.1 Distortion [%] 0.01 VCC = ±8.0V VCC = ±8.0V 0.01 –4 0 4 8 12 16 Output level [dB] 20 –4 0 4 8 12 16 Output level [dB] 20 – 16 – CXA1560S, CXA1561M/S, CXA1562M/S Cross talk –40 –50 –60 –70 PB ch to ch –80 –90 –100 PB to REC 100 200 500 1k 2k Frequency [Hz] 5k 10k REC to PB REC ch to ch VCC = ±6V Input = +10dB Refer to Dolby Level NR OFF Cross talk [dB] NR control threshold 14 VCC VCN–NR control voltage [V] 12 10 8 6 4 2 0 4 6 8 10 12 14 VCC–Supply voltage [V] 16 NR OFF C type VCC 2 B type MODE control threshold 14 VCC VCM–MODE control voltage [V] 12 MPX ON 10 8 6 4 2 0 4 6 8 10 12 14 VCC–Supply voltage [V] 16 PB VCC 2 MPX OFF – 17 – CXA1560S, CXA1561M/S, CXA1562M/S Package Outline Unit: mm CXA1561M, CXA1562M 24PIN SOP (PLASTIC) + 0.4 15.0 – 0.1 24 13 + 0.4 1.85 – 0.15 0.15 + 0.3 5.3 – 0.1 7.9 ± 0.4 + 0.2 0.1 – 0.05 0.45 ± 0.1 1.27 + 0.1 0.2 – 0.05 ± 0.12 M PACKAGE STRUCTURE MOLDING COMPOUND SONY CODE EIAJ CODE JEDEC CODE SOP-24P-L01 ∗SOP024-P-0300-A LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY/PHENOL RESIN SOLDER PLATING COPPER ALLOY / 42ALLOY 0.3g CXA1560S, CXA1561S, CXA1562S 22PIN SDIP (PLASTIC) + 0.1 0.05 0.25 – 12 + 0.4 19.2 – 0.1 22 + 0.3 6.4 – 0.1 1 1.778 11 0.5 ± 0.1 + 0.15 0.9 – 0.1 + 0.15 3.25 – 0.2 0.51 MIN + 0.4 3.9 – 0.1 PACKAGE STRUCTURE MOLDING COMPOUND SONY CODE EIAJ CODE JEDEC CODE SDIP-22P-01 SDIP022-P-0300 LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY RESIN SOLDER PLATING COPPER ALLOY 0.95g – 18 – 7.62 0° to 15° 0.5 ± 0.2 1 12 6.9