CXA1619AM

CXA1619AM/AS FM/AM Radio For the availability of this product, please contact the sales office. Description CXA1619AM/AS is a one-chip FM/AM radio IC designed for radio-cassette tape recorders and headphone tape recorders, and has the following functions. Features • Small number of peripheral components. • Low current consumption (VCC=3 V) For FM : ID=5.8 mA (Typ.) For AM : ID=4.7 mA (Typ.) • Built-in FM/AM select switch. • Large output of AF amplifier. EIAJ output=450 mW (Typ.) when VCC=6 V, load impedance 8 Ω Function FM section • RF amplifier, Mixer and OSC (incorporating AFC variable capacitor). • IF amplifier • Quadrature detection • Tuning LED driver AM section • RF amplifier, Mixer and OSC (with RF AGC) • IF amplifier (with IF AGC) • Detector • Tuning LED driver AF section • Electronic volume control Structure Bipolar monolithic IC CXA1619AM 28 pin SOP (Plastic) CXA1619AS 30 pin SDIP (Plastic) Absolute Maximum Ratings (Ta=25 °C) • Supply voltage VCC 14 V • Operating temperature Topr –10 to +60 °C • Storage temperature Tstg –50 to +125 °C • Allowable power dissipation PD 700 mW (CXA1619AM) PD 1000 mW (CXA1619AS) Recommended Operating Conditions Supply voltage VCC 2 to 7.5 V (CXA1619AM) VCC 2 to 8.5 V (CXA1619AS) Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. —1— E98419-TE CXA1619AM/AS Block Diagram CXA1619AM AF GND OUT 28 27 Ripple AF VCC FILTER IN 26 25 24 DET AFC AFC OUT AGC AGC 23 22 21 IF GND METER NC 20 19 18 FM/AM FM AM BAND IF IN IF IN SELECT 17 16 15 AM IF DET AGC TUNING METER AF POWER AMP AM FE FM DISCRIMINATOR FM FE FM IF 1 GND 2 3 4 VOL 5 AM OSC 6 AFC 7 8 9 FM RF FM NF DISCRI FM Reg OSC OUT 10 AM RF IN 11 NC 12 13 14 FM FE FM/AM RF IN GND FE OUT CXA1619AS AF GND GND OUT 30 29 28 VCC 27 Ripple AF FILTER IN 26 25 DET AFC AFC OUT AGC AGC 24 23 22 IF GND METER NC 21 20 19 FM/AM FM AM BAND IF IN IF IN SELECT 18 17 16 AM IF DET AGC TUNING METER AF POWER AMP AM FE FM IF FM DISCRIMINATOR FM FE 1 2 3 4 5 VOL 6 AM OSC 7 AFC 8 9 GND GND FM NF DISCRI FM Reg OSC OUT 10 FM RF 11 AM RF IN 12 NC 15 13 14 FM FE FM/AM RF IN GND FE OUT —2— CXA1619AM/AS Standard Circuit Design Data No. 1 (1, 2) Symbol Voltage (V) VCC=3 V VCC=6 V FM AM FM AM 0 0 0 0 (The pin numbers in the parenthesis are for CXA1619AS.) Equivalent circuit Description GND 2 2 (3) FM DISCRI 2.18 2.70 4.88 5.43 1.2k 1k Phase-shift circuit Connect ceramic discriminator 3 (4) NF 1.5 1.5 3.0 3.0 VCC ×100 27 ×100 Negative feedback pin 27 (28) AF OUT 1.5 1.5 3.0 3.0 3 GND Power amplifier output pin 4 20k 4 (5) VOL CONT 1.25 1.25 1.25 1.25 80k GND Connect variable resistor for electronic volume control. 5 5 (6) AM OSC 1.25 1.25 1.25 1.25 3.6k AM local oscillation circuit 6 (7) 8 (9) AFC REG OUT 1.25 ∗ 1.25 ∗ 6 8 1.25V (REG) AFC variable capacitor pin Regulator pin 1.25 V (Typ.) 1.25 1.25 1.25 1.25 7 7 (8) FM OSC 1.25 1.25 1.25 1.25 FM local oscillation circuit —3— CXA1619AM/AS No. Symbol Voltage (V) VCC=3 V VCC=6 V FM AM FM AM 1.25 1.25 1.25 1.25 Equivalent circuit Description 3p 9 (10) FM RF 9 8k Connect FM RF tuning coil 12 (13) FM RF IN 0.3 0 0.3 0 12 1k FM RF input pin 10 10 (11) AM RF IN 1.25 1.25 1.25 1.25 VCC AM RF input pin 11 (12) NC 13 (14) GND (FE GND) 0 0 0 0 0 0 0 0 AM FM FM/AM 14 (15) FE OUT 0.36 0.2 0.36 0.2 220 14 IF output pin of FM and AM. Connect IF filter. VCC 15 (16) BAND SELECT 1.30 0 1.30 0 15 GND FM and AM bands selection switch pin. During GND it becomes AM and during open it becomes FM. 16 (17) AM IF IN 0 0 0 0 16 2k Input pin of AM IF. 17 (18) FM IF IN 18 (19) NC 0.34 0 0 0 0.88 0 0 0 Input pin of FM IF. —4— CXA1619AM/AS No. Symbol Voltage (V) VCC=3 V VCC=6 V FM AM FM AM Equivalent circuit Description 19 1.25V ×3 19 (20) METER 1.6 1.6 4.5 4.5 N GND Meter drive circuit (For tuning indicator) 20 (21) GND 0 0 0 0 AFC pin of W band. During AM, it determines time constant of AGC AFC pin of J band. During AM, it determines time constant of AGC. Detection output pin 21 (22) AFC/AGC 1.25 1.49 1.25 1.49 22 22 (23) AFC/AGC 1.25 1.25 1.25 1.25 23 33k 39k 21 GND 23 (24) DET OUT 1.25 1.0 1.25 1.0 11k 24 24 (25) AF IN 0 0 0 0 ×4 ×4 82k GND Power amplifier input pin VCC 25 (26) RIPPLE FILTER 17k 2.71 2.71 5.4 5.4 25 73k 90k Ripple filter 26 (27) VCC 28 GND (29, 30) 3.0 3.0 6.0 6.0 0 0 0 0 Power supply pin Power GND ∗ The pin voltage of pin 6 during AM, it is the same pin voltage of pin 22 (23) during J BAND and is the same pin voltage of pin 21 (22) during W BAND. —5— Electrical Characteristics Symbol Min. — — 32 39 77.5 4.8 7.6 39 10.0 14.0 46 mA mA dB 155 mVrms Typ. Max. Unit ID1 ID2 GV1 VD1 A——A B A VD 1 A A A No signal, AM No signal, FM VIN1=40 dBµV, 100 MHz 6 A A A Conditions (See the Electrical Characteristics Test Circuit, Ta=25 °C, VCC=6 V) No. Item 1 2 3 AM circuit current FM circuit current FM front end voltage gain SW conditions 2345 BAAA BAAB BAAB Test Point IA IA VA 4 FM detection output level 5 FM IF knee level VD2 A——A B A VD — 24 32 dBµV 6 IB1 VIN3=60 dBµV, 10.7 MHz VIN2=60 dBµV, 1660 kHz GV2 GV3 VD3 IB2 THD2 GV4 THD3 A————B A————B A A B B A A VD VE VE A A—A A A IM A A—A A A VD A A—A A A VD A A A A A A VB A——A B A IM FM detection output distortion factor THD1 A——A B A VD VIN3=90 dBµV, 10.7 MHz (1 kHz, 22.5 kHz DEV) VIN3=level at a point 3 dB down from VIN3=90 dBµV, 10.7 MHz (1 kHz, 22.5 kHz DEV) VIN3=90 dBµV, 10.7 MHz (1 kHz, 75 kHz DEV) — 1.8 15 14 39 1.3 — VIN4=–30 dBm, 1 kHz Distortion factor for output of 50 mW VIN4=–20 dBm, 1 kHz 27 — 0.3 3.5 22 20 77.5 3.0 0.6 31.5 0.9 2.0 7.0 29 27 % mA dB dBµV 155 mVrms 7.0 2.0 36 2.5 mA % dB % 7 FM meter current —6— 8 AM front end voltage gain 9 AM IF voltage gain 10 AM detection output level VIN3 when 455 kHz (1 kHz, 30 % MOD) output is –34 dBm VIN3=85 dBµV, 455 kHz (1 kHz, 30 % MOD) VIN3=85 dBµV, 455 kHz VIN2=95 dBµV, 1660 kHz (1 kHz, 30 % MOD) 11 AM meter current 12 AM detection output distortion factor 13 Audio voltage gain 14 Audio distortion factor CXA1619AM/AS 0 dBµV=1 µV Electrical Characteristics Test Circuit REG 10µ 150 24p BPF 30p S1 1000p 8p 10 AM RF IN FM RF Reg OUT FM OSC AFC AM OSC VOL NF 14 FM/AM FE FM FE OUT GND RF IN NC 13 12 11 30p 1µ 150 CF3 33k 33k BA 10p 50k 150µH 43p 100k OSC AFC 24k 24k 100 0.01µ VIN2 VIN1 0.01µ VA 330 B A S2 24p 2k 9 8 7 6 5 4 3 2 1 FM GND DISCRI 2k CXA1619AM IFT CF1 —7— FM/AM BAND AM SELECT IF IN FM IF IN 17 18 21 19 20 22 1µ B A 0.01µ IM 1µ 4.7µ 0.012µ VD 23 IF NC METER GND AFC AGC AFC AGC DET OUT 15 0.01µ S5 B 16 AF IN 24 S6 A B S4 0.01µ A A VIN4 VB 30p Ripple FILTER VCC 25 1µ 26 AF OUT 27 GND 28 VE 470µ 5k 0.047µ 100µ CF1 CF3 IFT OSC 0.047µ 8 GND VCC : AM 455kHz C.F. : FM DISCRIMINATOR : AM 455kHz IFT : AM OSC CXA1619AM/AS S3 B VIN3 Application Circuit 1 ANT L1 C2 18p L4 R2 10k R3 CF3 150 C3 22p C4 6p L2 C1 2p L3 RV1 50k BPF C5 10µ C7 1p 11 NC AM RF IN FM RF Reg OUT FM OSC AFC AM OSC VOL NF 10 R1 100k C8 4.7µ 50 14 C6 0.01µ 13 12 9 8 7 6 3 5 4 2 1 FM/AM FE FM FE OUT GND RF IN FM GND DISCRI S2 —8— CXA1619AM FM IF IN 17 18 19 20 21 22 23 24 IF NC METER GND AFC AGC AFC AGC DET OUT AF IN 15 16 25 C15 0.47µ 50V CF1 R5 330 CF2 C12 10µ 50V R6 1k C13 10µ 50V C14 4.7µ 50V R7 D1 C16 0.022µ C17 10µ 50V C19 0.1µ FM/AM BAND AM SELECT IF IN Ripple FILTER VCC 26 AF OUT 27 GND 28 EPJ S1 C11 100p T1 FM BATT R4 2.2k AM C10 0.01µ C18 470µ 6.3V C20 0.1µ C21 220µ 10V CXA1619AM/AS Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. Application Circuit 2 ANT L1 C2 18p L4 R2 10k R3 CF3 150 C3 22p C4 6p L2 C1 2p L3 RV1 50k BPF C5 10µ C7 1p 12 NC AM RF IN FM RF Reg OUT FM OSC AFC AM OSC VOL NF 11 10 R1 100k C8 4.7µ 50 15 C6 0.01µ 13 14 9 8 7 6 5 4 3 2 1 GND FM/AM FE FM FE OUT GND RF IN FM GND DISCRI —9— CXA1619AS FM IF IN 18 19 20 21 22 23 24 25 IF NC METER GND AFC AGC AFC AGC DET OUT AF IN Ripple FILTER VCC 26 C15 0.47µ 50V CF1 R5 330 CF2 C12 10µ 50V C13 10µ 50V R6 1k C14 4.7µ 50V R7 D1 C16 0.022µ C17 10µ 50V 27 C19 0.1µ 16 17 S2 FM/AM BAND AM SELECT IF IN AF OUT 28 GND 29 GND 30 EPJ S1 C11 100p T1 FM BATT R4 2.2k AM C10 0.01µ C18 470µ 6.3V C20 0.1µ C21 220µ 10V CXA1619AM/AS Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. CXA1619AM/AS Coil data AM OSC S 3 2 1 Core diameter ø 0.06 mm 2UEW 4 5 6 f (kHz) 796 L (µH) 1 to 3 270 QO 1 to 3 125 Number of widings (t) 1 to 3 4 to 6 107 29 Equivalent to L-5K7-H5 R12-1684X. Mitsumi Electric Co., Ltd. or 7TRS-8441X TOKO Co., Ltd. AM IFT 3 2 1 S Core diameter ø 0.07 mm UEW 4 5 6 CO (pF) 1 to 3 180 QO 1 to 3 90 Number of widings (t) 1 to 2 2 to 3 4 to 6 111 35 7 Equivalent to 21K7-H5 R12-8558A. Mitsumi Electric Co., Ltd. or 7MC-7789N TOKO Co., Ltd. FM RF φ 4mm φ 0.6mm 4.5t FM OSC φ 4mm φ 0.6mm 3.5t AM bar antenna f (kHz) 796 L (µH) 650 Primary 91 t Secondary 20 t Primary Secondary BPF PFWE8 (88 to 108 MHz) SFU-455B SFE10.7MA5 CDA10.7MC1 Soshin Electric Co., Ltd. Murata Mfg. Co., Ltd. Or BFCFL-455 TOKO Co., Ltd. Murata Mfg. Co., Ltd. Murata Mfg. Co., Ltd. —10— CF1 CF2 CF3 CXA1619AM/AS Package Outline CXA1619AM Unit : mm 28PIN SOP (PLASTIC) + 0.4 18.8 – 0.1 28 15 + 0.4 2.3 – 0.15 0.15 + 0.2 0.1 – 0.05 + 0.3 7.6 – 0.1 10.3 ± 0.4 9.3 1 0.45 ± 0.1 14 1.27 + 0.1 0.2 – 0.05 0.24 M PACKAGE STRUCTURE PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE SOP-28P-L04 SOP028-P-0375 LEAD TREATMENT LEAD MATERIAL PACKAGE MASS EPOXY RESIN SOLDER PLATING 42/COPPER ALLOY 0.7g CXA1619AS 30PIN SDIP (PLASTIC) + 0.4 26.9 – 0.1 30 16 + 0.3 8.5 – 0.1 + 0.1 05 0.25 – 0. 0.5 ± 0.2 0° to 15° EPOXY RESIN SOLDER/PALLADIUM PLATING COPPER ALLOY 1.8g 1 1.778 15 0.5 MIN + 0.4 3.7 – 0.1 10.16 Two kinds of package surface: 1.All mat surface type. 2.All mirror surface type. 0.5 ± 0.1 0.9 ± 0.15 PACKAGE STRUCTURE MOLDING COMPOUND SONY CODE EIAJ CODE JEDEC CODE SDIP-30P-01 SDIP030-P-0400 LEAD TREATMENT LEAD MATERIAL PACKAGE MASS NOTE : PALLADIUM PLATING This product uses S-PdPPF (Sony Spec.-Palladium Pre-Plated Lead Frame). —11— 3.0 MIN