74ACT244

® 74ACT244 OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED) s s s s s s s s s HIGH SPEED: tPD = 4.5 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 8 µA (MAX.) at TA = 25 oC COMPATIBLE WITH TTL OUTPUTS VIH = 2V (MIN), VIL = 0.8V (MAX) 50Ω TRANSMISSION LINE DRIVING CAPABILITY SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC (OPR) = 4.5V to 5.5V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 244 IMPROVED LATCH-UP IMMUNITY M (Micro Package) B (Plastic Package) ORDER CODES : 74ACT244B 74ACT244M 74ACT244T T (TSSOP Package) DESCRIPTION The ACT244 is an advanced CMOS OCTAL BUS BUFFER (3-STATE) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power applications mantaining high speed operation similar to equivalent Bipolar Schottky TTL. G control output governs four BUS BUFFERs. This device is desibned to be used with 3 state memory address drivers, etc. The device is designed to interface directly High Speed CMOS systems with TTL, NMOS and CMOS output voltage levels. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS February 1999 1/9 74ACT244 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No 1 2, 4,6, 8 9, 7,5, 3 11, 13, 15, 17 18, 16, 14, 12 19 10 20 SYMBOL 1G 1A1 to 1A4 2Y1 to 2Y4 2A1 to 2A4 1Y1 to 1Y4 2G GND VCC NAME AND FUNCT ION Output Enable Input Data Inputs Data Outputs Data Inputs Data Outputs Output Enabel Input Ground (0V) Positive Supply Voltage TRUTH TABLE INPUT G L L H X:”H” or ”L” Z: High impedance OUTPUT An L H X Yn L H Z ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO ICC orIGND Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current DC VCC or Ground Current Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 50 ± 400 -65 to +150 300 Unit V V V mA mA mA mA o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top dt/dv Supply Voltage Input Voltage Output Voltage Operating Temperature: Input Rise and Fall Time VCC = 4.5 to 5.5V (note 1) Parameter Value 4.5 to 5.5 0 to VCC 0 to VCC -40 to +85 8 Unit V V V o C ns/V 1) VIN from 0.8 V to 2.0 V 2/9 74ACT244 DC SPECIFICATIONS Symb ol Parameter V CC (V) VIH VIL VOH High Level Input Voltage Low Level Input Voltage High Level Output Voltage 4.5 5.5 4.5 5.5 4.5 5.5 4.5 5.5 VOL Low Level Output Voltage 4.5 5.5 4.5 5.5 II IOZ ICCT ICC IOLD IOHD Input Leakage Current 3 State Output Leakage Current Max ICC /Input Quiescent Supply Current Dynamic Output Current (note 1, 2) 5.5 5.5 5.5 5.5 5.5 VI = VIH or VIL (*) Test Co nditions Min. VO = 0.1 V or VCC - 0.1 V VO = 0.1 V or VCC - 0.1 V VI(*) = VIH or VIL IO=-50 µA IO=-50 µA IO=-24 mA IO=-24 mA IO=50 µA IO=50 mA IO=24 mA IO=24 mA VI = VCC orGND VI = VIH orVIL VO = VCC orGND VI = VCC -2.1V VI = VCC orGND VOLD = 1.65 V max VOHD = 3.85 V min 0.6 4.4 5.4 3.86 4.86 0.001 0.001 2.0 2.0 T yp. 1.5 1.5 1.5 1.5 4.49 5.49 Valu e T A = 25 oC Max. -40 to 85 o C Min. 2.0 2.0 0.8 0.8 4.4 5.4 3.76 4.76 0.1 0.1 0.36 0.36 ±0.1 ±0.5 0.1 0.1 0.44 0.44 ±1 ±5 1.5 8 75 -75 80 0.8 0.8 Max. Un it V V V V µA µA mA µA mA mA 1) Maximum test duration 2ms, one output loaded attime 2) Incident wave switching is guaranteed on transmission lines with impedances as low as 50 Ω. (*) All outputs loaded. 3/9 74ACT244 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, RL = 500 Ω, Input tr = tf =3 ns) Symb ol Parameter V CC (V) tPLH tPHL tPZL tPZH tPLZ tPHZ Propagation Delay Time Output Enable Time Output Disable Time 5.0 (*) T est Con ditio n Valu e T A = 25 oC -40 to 85 o C Min. 1.5 1.5 1.5 T yp. 4.5 5.5 6.5 Max. 9.0 9.0 10.0 Min. 1.5 1.5 1.5 Max. 10.0 10.0 11.0 Un it ns ns ns 5.0(*) 5.0(*) (*) Voltage range is 5V ± 0.5V CAPACITIVE CHARACTERISTICS Symb ol Parameter V CC (V) CIN Ci/o CPD Input Capacitance I/O Capacitance Power Dissipation Capacitance (note 1) 5.0 5.0 5.0 Test Co nditions o Valu e -40 to 85 C T A = 25 C Min. T yp. Max. Min. Max. 4 8 24 o Un it pF pF pF 1) CPD isdefined as the value of the IC’sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. (Referto Test Circuit).Average operating current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC/n (per circuit) TEST CIRCUIT T EST tPLH , tPHL tPZL , tPLZ tPZH , tPHZ CL = 50 pF or equivalent (includes jigand probe capacitance) RL = R1 = 500Ω orequivalent RT = ZOUT of pulse generator (typically 50Ω) SW IT CH Open 2VCC Open 4/9 74ACT244 WAVEFORM 1: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 5/9 74ACT244 Plastic DIP-20 (0.25) MECHANICAL DATA mm MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.34 8.5 2.54 22.86 7.1 3.93 0.130 0.053 0.254 1.39 0.45 0.25 25.4 0.335 0.100 0.900 0.280 0.155 1.65 TYP. MAX. MIN. 0.010 0.055 0.018 0.010 1.000 0.065 inch TYP. MAX. DIM. P001J 6/9 74ACT244 SO-20 MECHANICAL DATA DIM. MIN. A a1 a2 b b1 C c1 D E e e3 F L M S 7.40 0.50 12.60 10.00 1.27 11.43 7.60 1.27 0.75 8 (max.) 0.291 0.19 13.00 10.65 0.35 0.23 0.50 45 (typ.) 0.496 0.393 0.050 0.450 0.299 0.050 0.029 0.512 0.419 0.10 mm TYP. MAX. 2.65 0.20 2.45 0.49 0.32 0.013 0.009 0.020 0.004 MIN. inch TYP. MAX. 0.104 0.007 0.096 0.019 0.012 P013L 7/9 74ACT244 TSSOP20 MECHANICAL DATA mm MIN. A A1 A2 b c D E E1 e K L 0o 0.50 0.05 0.85 0.19 0.09 6.4 6.25 4.3 6.5 6.4 4.4 0.65 BSC 4o 0.60 8o 0.70 0o 0.020 0.10 0.9 TYP. MAX. 1.1 0.15 0.95 0.30 0.2 6.6 6.5 4.48 0.002 0.335 0.0075 0.0035 0.252 0.246 0.169 0.256 0.252 0.173 0.0256 BSC 4o 0.024 8o 0.028 0.004 0.354 MIN. inch TYP. MAX. 0.433 0.006 0.374 0.0118 0.0079 0.260 0.256 0.176 DIM. A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 8/9 74ACT244 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics © 1999 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com . 9/9