74LVQ138MTR

74LVQ138 3 TO 8 LINE DECODER (INVERTING) ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 5.5ns (TYP.) at VCC = 3.3 V COMPATIBLE WITH TTL OUTPUTS LOW POWER DISSIPATION: ICC = 4 µA (MAX.) at TA=25°C LOW NOISE: VOLP = 0.2V (TYP.) at VCC = 3.3V 75Ω TRANSMISSION LINE DRIVING CAPABILITY SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 12mA (MIN) at VCC = 3.0 V PCI BUS LEVELS GUARANTEED AT 24 mA BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 3.6V (1.2V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 138 IMPROVED LATCH-UP IMMUNITY DESCRIPTION The 74LVQ138 is a low voltage CMOS 3 TO 8 LINE DECODER (INVERTING) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power and low noise 3.3V applications. SOP TSSOP Table 1: Order Codes PACKAGE T&R SOP TSSOP 74LVQ138MTR 74LVQ138TTR If the device is enabled, 3 binary select inputs (A, B, and C) determine which one of the outputs will go low. If enable input G1 is held low or either G2A or G2B is held high, the decoding function is inhibited and all the 8 outputs go to high. Three enable inputs are provided to ease cascade connection and application of address decoders for memory systems. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. Figure 1: Pin Connection And IEC Logic Symbols July 2004 Rev. 5 1/12 74LVQ138 Figure 2: Input And Output Equivalent Circuit Table 2: Pin Description PIN N° SYMBOL 1, 2, 3 4, 5 6 15, 14, 13, 12, 11, 10, 9, 7 8 16 A, B, C G2A, G2B G1 Y0 to Y7 GND VCC NAME AND FUNCTION Address Inputs Enable Inputs Enable Input Outputs Ground (0V) Positive Supply Voltage Table 3: Truth Table INPUTS OUTPUTS ENABLE SELECT G2B G2A G1 C B A Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 X X H L L L L L L L L X H X L L L L L L L L L X X H H H H H H H H X X X L L L L H H H H X X X L L H H L L H H X X X L H L H L H L H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L H H H H H H H H H H H L X : Don’t Care Figure 3: Logic Diagram This logic diagram has not be used to estimate propagation delays 2/12 74LVQ138 Table 4: Absolute Maximum Ratings Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V VI DC Input Voltage -0.5 to VCC + 0.5 V VO DC Output Voltage -0.5 to VCC + 0.5 ± 20 V mA ± 20 mA IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Current ICC or IGND DC VCC or Ground Current Storage Temperature Tstg TL ± 50 mA ± 200 mA -65 to +150 °C 300 °C Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Table 5: Recommended Operating Conditions Symbol VCC Parameter Value Unit Supply Voltage (note 1) 2 to 3.6 V VI Input Voltage 0 to VCC V VO Output Voltage Top Operating Temperature dt/dv Input Rise and Fall Time VCC = 3.0V (note 2) 0 to VCC V -55 to 125 °C 0 to 10 ns/V 1) Truth Table guaranteed: 1.2V to 3.6V 2) VIN from 0.8V to 2V Table 6: DC Specifications Test Condition Symbol VIH VIL VOH Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage TA = 25°C VCC (V) Min. Typ. Max. 2.0 3.0 to 3.6 3.0 Value Low Level Output Voltage 3.0 -55 to 125°C Min. Min. 0.8 IO=-50 µA 2.9 IO=-12 mA 2.58 2.99 2.9 2.9 2.48 2.2 IO=50 µA 0.002 0.1 IO=12 mA 0 0.36 ICC IOLD IOHD Input Leakage Current Quiescent Supply Current Dynamic Output Current (note 1, 2) V 0.8 2.48 Unit Max. 2.0 0.8 IO=24 mA II Max. 2.0 IO=-24 mA VOL -40 to 85°C V V 2.2 0.1 0.1 0.44 0.44 0.55 0.55 V 3.6 VI = VCC or GND ± 0.1 ±1 ±1 µA 3.6 VI = VCC or GND 4 40 40 µA 3.6 VOLD = 0.8 V max 36 25 mA VOHD = 2 V min -25 -25 mA 1) Maximum test duration 2ms, one output loaded at time 2) Incident wave switching is guaranteed on transmission lines with impedances as low as 75Ω 3/12 74LVQ138 Table 7: Dynamic Switching Characteristics Test Condition Symbol VOLP VOLV VIHD VILD Parameter Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3) Value TA = 25°C VCC (V) Min. 3.3 -0.8 3.3 Typ. Max. 0.2 0.8 -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. V -0.2 2 V CL = 50 pF 3.3 0.8 V 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.3V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.3V. Inputs under test switching: 3.3V to threshold (VILD), 0V to threshold (VIHD), f=1MHz. Table 8: AC Electrical Characteristics (CL = 50 pF, RL = 500 Ω, Input tr = tf = 3ns) Test Condition Symbol Parameter tPLH tPHL Propagation Delay Time A, B, C to Y tPLH tPHL Propagation Delay Time G1 to Y tPLH tPHL Propagation Delay Time G2A or G2B to Y tOSLH Output To Output tOSHL Skew Time (note1, 2) Value TA = 25°C VCC (V) Min. -40 to 85°C -55 to 125°C Min. Min. Typ. Max. 6.6 10.5 12.0 14.0 5.5 8.0 9.0 10.5 2.7 6.7 10.5 12.0 14.0 3.3(*) 5.6 8.0 9.0 10.5 2.7 6.3 10.5 12.0 14.0 5.2 8.0 9.0 10.5 0.5 0.5 1.0 1.0 1.0 1.0 1.0 1.0 2.7 (*) 3.3 (*) 3.3 2.7 (*) 3.3 Max. Unit Max. ns ns ns ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = |tPLHm - tPLHn|, tOSHL = |tPHLm - tPHLn|) 2) Parameter guaranteed by design (*) Voltage range is 3.3V ± 0.3V Table 9: Capacitive Characteristics Test Condition Symbol Parameter TA = 25°C VCC (V) CIN Input Capacitance 3.3 CPD Power Dissipation Capacitance (note 1) 3.3 Value Min. fIN = 10MH Typ. Max. -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. 4 pF 50 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 4/12 74LVQ138 Figure 4: Test Circuit CL = 50pF or equivalent (includes jig and probe capacitance) RL = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) Figure 5: Waveform - Propagation Delays For Inverting Outputs (f=1MHz; 50% duty cycle) 5/12 74LVQ138 Figure 6: Waveform - Propagation Delays For Non-inverting Outputs (f=1MHz; 50% duty cycle) 6/12 74LVQ138 SO-16 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.25 a2 MAX. 0.004 0.010 1.64 0.063 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 10 0.385 0.393 E 5.8 6.2 0.228 0.244 e 1.27 e3 0.050 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) 0016020D 7/12 74LVQ138 TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0079 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0˚ L 0.45 A 0.60 0.0256 BSC 8˚ 0˚ 0.75 0.018 8˚ 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 8/12 74LVQ138 Tape & Reel SO-16 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 6.45 6.65 0.254 0.262 Bo 10.3 10.5 0.406 0.414 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 9/12 74LVQ138 Tape & Reel TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. A MAX. MIN. 330 13.2 TYP. MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 10/12 TYP 0.504 22.4 0.519 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 74LVQ138 Table 10: Revision History Date Revision 29-Jul-2004 5 Description of Changes Ordering Codes Revision - pag. 1. 11/12 74LVQ138 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 12/12