BULD118D-1

® BULD118D-1 HIGH VOLTAGE FAST-SWITCHING NPN POWER TRANSISTOR s s s s s INTEGRATED ANTIPARALLEL COLLECTOR- EMITTER DIODE HIGH VOLTAGE CAPABILITY LOW SPREAD OF DYNAMIC PARAMETERS MINIMUM LOT-TO-LOT SPREAD FOR RELIABLE OPERATION VERY HIGH SWITCHING SPEED 2 1 3 APPLICATIONS: ELECTRONIC BALLASTS FOR FLUORESCENT LIGHTING s FLYBACK AND FORWARD SINGLE TRANSISTOR LOW POWER CONVERTERS s IPAK (TO-251) DESCRIPTION The device is manufactured using high voltage Multi Epitaxial Planar technology for high switching speeds and medium voltage capability. It uses a Cellular Emitter structure with planar edge termination to enhance switching speeds while maintaining the wide RBSOA. The device is designed for use in lighting applications and low cost switch-mode power supplies. INTERNAL SCHEMATIC DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol V CES V CEO V EBO IC I CM IB I BM P tot T stg Tj Parameter Collector-Emitter Voltage (V BE = 0 ) Collector-Emitter Voltage (I B = 0 ) Emitter-Base Voltage (I C = 0 ) Collector Current Collector Peak Current (t p < 5 m s) Base Current Base Peak Current (t p < 5 m s) Total Dissipation at T c = 2 5 C Storage Temperature Max. Operating Junction Temperature o Value 700 400 9 2 4 1 2 20 -65 to 150 150 Unit V V V A A A A W o o C C 1/7 June 2001 BULD118D-1 THERMAL DATA R thj-case R thj-amb Thermal Resistance Junction-Case Thermal Resistance Junction-Ambient Max Max 6.25 100 o o C/W C/W ELECTRICAL CHARACTERISTICS (Tcase = 25 oC unless otherwise specified) Symbol I CES V EBO VCEO(sus) I CEO V CE(sat) ∗ Parameter Collector Cut-off Current (V BE = 0 ) Emitter-Base Voltage Collector-Emitter Sustaining Voltage Collector-Emitter Leakage Current Collector-Emitter Saturation Voltage Base-Emitter Saturation Voltage DC Current Gain Test Conditions V CE = 7 00 V V CE = 7 00 V I E = 1 0 mA I C = 1 00 mA V CE = 4 00 V I C = 0 .5 A IC = 1 A IC = 2 A I C = 0 .5 A IC = 1 A IC = 2 A I C = 1 0 mA I C = 0 .5 A IC = 2 A V CC = 1 25 V I B1 = 0 .4 A tp = 30 µs I B = 0 .1 A I B = 0 .2 A I B = 0 .4 A I B = 0 .1 A I B = 0 .2 A I B = 0 .4 A V CE = 5 V V CE = 5 V V CE = 5 V IC = 2 A I B2 = - 0.2 A 1.4 2 IC = 1 A V BE = -5 V V clamp = 300 V I B1 = 0 .2 A L = 50 mH 0 .8 0.10 2 .5 10 10 8 0.7 0.3 L = 25 mH T j = 1 25 o C 9 400 250 0.5 1 1.5 1.0 1.2 1.3 50 Min. Typ. Max. 100 500 Unit µA µA V V µA V V V V V V V BE(sat) ∗ h FE ∗ tr tf ts RESISTIVE LOAD Rise Time Fall Time Storage Time group A group B INDUCTIVE LOAD Storage Time Fall Time 0.5 2.1 2.75 µs µs µs µs µs µs V ts tf VF Diode Forward Voltage I C = 1 A ∗ Pulsed: Pulse duration = 300 µs, duty cycle 1.5 % Note : Product is pre-selected in storage time (GROUP A and GROUP B). STMicroelectronics reserves the right to ship either groups according to production availability. Please contact your nearest STMicroelectronics sales office for delivery details. 2/7 BULD118D-1 Safe Operating Areas Derating Curve DC Current Gain DC Current Gain Collector Emitter Saturation Voltage Base Emitter Saturation Voltage 3/7 BULD118D-1 Inductive Fall Time Inductive Storage Time Resistive Fall Time Resistive Load Storage Time Reverse Biased SOA 4/7 BULD118D-1 Figure 1: Inductive Load Switching Test Circuit. 1) Fast electronic switch 2) Non-inductive Resistor 3) Fast recovery rectifier Figure 2: Resistive Load Switching Test Circuit. 1) Fast electronic switch 2) Non-inductive Resistor 5/7 BULD118D-1 TO-251 (IPAK) MECHANICAL DATA DIM. MIN. A A1 A3 B B2 B3 B5 B6 C C2 D E G H L L1 L2 V1 0.45 0.48 6.00 6.40 4.40 15.90 9.00 0.80 0.80 10 o mm TYP. MAX. 2.40 1.10 1.30 0.90 5.40 0.85 0.30 0.95 0.60 0.60 6.20 6.60 4.60 16.30 9.40 1.20 1.00 0.018 0.019 0.237 0.252 0.173 0.626 0.354 0.031 MIN. 0.087 0.035 0.028 0.025 0.204 2.20 0.90 0.70 0.64 5.20 inch TYP. MAX. 0.094 0.043 0.051 0.035 0.213 0.033 0.012 0.037 0.024 0.024 0.244 0.260 0.181 0.642 0.370 0.047 0.031 10 o 0.039 P032N_E 6/7 BULD118D-1 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics © 2001 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com 7/7