0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
EVL130W-STRLIG

EVL130W-STRLIG

  • 厂商:

    STMICROELECTRONICS(意法半导体)

  • 封装:

    -

  • 描述:

    BOARD EVAL L6562AT L6599AT

  • 数据手册
  • 价格&库存
EVL130W-STRLIG 数据手册
AN3106 Application note 48 V - 130 W high-efficiency converter with PFC for LED street lighting applications By Claudio Spini Introduction The use and growing popularity of LEDS, thanks to their high efficiency and very long lifetime, are driving the innovation of different types of lamps and contributing to the reduction of energy consumption for internal and external lighting. Streetlight applications require that the power supply designed to power an LED lamp must have high efficiency and at least an equivalent lifetime in order to guarantee maintenance-free operation during the life of the LED. This application note describes the characteristics and features of a 130 W evaluation board (STEVAL-ILL053V1), tailored to an LED power supply specification for street lighting. The circuit is composed of two stages: a front-end PFC using the L6562AT and an LLC resonant converter based on the L6599AT. The strengths of this design are very high efficiency, wide input mains range (85 - 305 VAC) operation and long-term reliability. Because reliability (MTBF - “mean time between failures”) in power supplies is typically affected by the high failure rate of electrolytic capacitors unless using very expensive types, this board shows a very innovative design approach. The board doesn't implement any electrolytic capacitors, but uses instead film capacitors from EPCOS. Component de-rating has been also carefully applied during the design phase, decreasing the stress of the components as recommended by the MIL-HDBK-217D. The number of components, thanks to the use of the new devices L6562AT and L6599AT has also been minimized, thus increasing the MTBF and optimizing the total component cost. Thanks to the high efficiency achieved, just a small heatsink for the PFC stage is needed, while the other power components are SMT (surface mount technology) like most of the passive components, thus decreasing the production labor cost. The board also has protection features in case of overload, short-circuit, open loop by each stage or input overvoltage. For this particular application, all protections in case of intervention have an auto-restart functionality. Figure 1. STEVAL-ILL053V1: 130 W SMPS for LED street lighting applications May 2016 DocID016775 Rev 3 1/31 www.st.com 31 Contents AN3106 Contents 1 Main characteristics and circuit description . . . . . . . . . . . . . . . . . . . . . 3 1.1 Power factor corrector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Resonant power stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3 Startup sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.4 Output voltage feedback loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.5 Overload and short-circuit protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1.6 Overvoltage and open loop protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Efficiency measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 Input current harmonics measurement . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4 Functional check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.1 PFC circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.2 Half-bridge resonant LLC circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 4.3 Dynamic load operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.4 Overcurrent and overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.5 Converter startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5 Thermal map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 Conducted emission precompliance measurement . . . . . . . . . . . . . . 18 7 Bill of material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 8 PFC coil specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 9 Transformer specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 2/31 DocID016775 Rev 3 AN3106 1 Main characteristics and circuit description Main characteristics and circuit description The main features of the SMPS are listed here below: 1.1 • Extended input mains range: 85 to 305 VAC - frequency 45 to 55 Hz • Output voltage: 48 V at 2.7 A • Long-life, electrolytic capacitors are not used • Mains harmonics: acc. to EN61000-3-2 Class-C • Efficiency at full load: better than 90% at 115 VAC • EMI: according to EN55022-Class-B, EN55015 • Safety: double insulation, according to EN60950, SELV • Dimensions: 75 x 135 mm, 30 mm components maximum height • PCB: single side, 35 µm, FR-4, mixed PTH/SMT Power factor corrector The PFC stage, working in transition mode, acts as a preregulator and powers the resonant stage with the output voltage of 450 V. The PFC power topology is a conventional boost converter, connected to the output of the rectifier bridge D3. It is completed by the coil L1, manufactured by MAGNETICA, the diode D2 and the capacitors C5, C6 and C7 in parallel. The PFC output capacitors are film type, 5 µF - 800 V manufactured by EPCOS. Using film capacitors to replace the typical electrolytic capacitors allows increasing considerably the MTBF of the board. The boost switch is represented by the power MOSFET Q2. The board is equipped with an input EMI filter necessary to filter the commutation noise coming from the boost stage. The PFC implements the controller L6562AT, a small and inexpensive controller that is guaranteed for operation over a wide temperature range. At startup, the L6562AT is supplied by the startup resistors R5, R8, R13 charging the capacitor C13. Once the PFC begins switching, a charge pump connected to the auxiliary winding of the PFC inductor L1 supplies both PFC and resonant controllers via a small linear regulator implemented by Q1. Once both stages have been activated, the controllers are supplied also by the auxiliary winding of the resonant transformer, assuring correct supply voltage during operation of all load conditions. The L1 auxiliary winding is also connected to the L6562AT pin #5 (ZCD) through the resistor R18. Its purpose is to provide the information that L1 has demagnetized, needed by the internal logic for triggering a new switching cycle. The PFC boost peak current is sensed by resistors R33 and R34 in series to the MOSFET source. The signal is fed into pin #4 (CS) of the L6562AT, via the filter R27 and C16. The divider R7, R12, R14 and R22 provides the L6562AT multiplier with the information of the instantaneous mains voltage that is used to modulate the peak current of the boost. The resistors R2, R6, R9 with R15 and R16 are dedicated to sense the output voltage and feed to the L6562AT the feedback information necessary to maintain the output voltage regulated. The components C11, R20 and C12 constitute the error amplifier compensation network necessary to keep the required loop stability. DocID016775 Rev 3 3/31 31 Main characteristics and circuit description 1.2 AN3106 Resonant power stage The downstream converter is a resonant LLC half-bridge stage working with 50 percent fixed duty cycle and variable frequency. It implements the ST L6599AT, integrating all functions necessary to properly control the resonant topology. The resonant transformer, manufactured by MAGNETICA, uses the integrated magnetic approach, so the leakage inductance is used for resonant operation of the circuit. Thus, no external, additional coil is needed for the resonance. The transformer secondary winding configuration is the typical center tap, using a couple of power Schottky rectifiers type STPS10150CG. The output capacitors are film type, 4.7 µF - 63 V from EPCOS. As for the PFC stage, using film capacitors allows considerably increasing the MTBF of the board. A small LC filter has been added on the output, in order to filter the high-frequency ripple. D21, D22, R55 constitute a voltage-controlled bleeder. In case of no-load operation of the SMPS, this circuit provides a bleeder limiting the output voltage from increasing, but not affecting the efficiency during normal operation. Please note that the converter has not been designed to work in this condition and therefore its mains consumption is not optimized (~3 W). 1.3 Startup sequence The PFC acts as master and therefore starts first. The resonant stage operates only if the PFC is delivering the nominal output voltage to prevent the resonant converter from working with an insufficient input voltage that can cause incorrect capacitive mode operation. Thus, both stages are designed to work according to this sequence. For correct sequencing the L6599AT makes use of the LINE pin (#7) to sense the PFC output voltage via a resistor divider. The L6599AT LINE pin (#7) has an internal comparator which has a hysteresis allowing to set independently the turn-on and turn-off voltage. At startup the LLC stage starts once the PFC output voltage reaches ~ 430 V, while the turn-off threshold has been set to ~330 V. 1.4 Output voltage feedback loop The output voltage is kept stable by means of a feedback loop implementing a typical circuit using a TS2431 modulating the current in the optocoupler diode. On the primary side, R43 - connecting pin RFMIN (#4) to the optocoupler's phototransistor allows modulating the L6599AT oscillator frequency, thus keeping the output voltage regulated. It also sets the maximum switching frequency at about 130 kHz. R42, that connects the same pin to ground, sets the minimum switching frequency. The R-C series R37 and C24 sets both soft-start maximum frequency and duration. 4/31 DocID016775 Rev 3 AN3106 Main characteristics and circuit description All evaluation boards implement the voltage loop circuitry previously described but in case a current loop is also required, it can be achieved by implementing the following modifications: • Replace R30 and R31 0R0 Ω resistors with sensing resistors, 0R033 and 0R039 respectively, both 0805 • Populate on PCB U4 and the relevant components shown on the schematic as N.M: C36 = 1N0-0805; C37 = 100NF-0805; R51 = 15R-0805; R56 = 1K0-0805; R6 = 22K-1206; C41 = 2N2-0805; U5 = SEA05TR • Remove TS2431AILT With these modifications the circuit is able to keep the output current constant at 2.7 A down to an output voltage value around 30 V. This function can be used to optimize the voltage drop and power dissipation in case current linear regulators are used to regulate the current flowing in each LED strip. If the output current is lower, the voltage loop will take over the operation, regulating the output voltage at its nominal value as when using the TS2431AILT. 1.5 Overload and short-circuit protection The current flowing into the primary winding, proportional to the output load, is sensed by the lossless circuit C34, R53, D19, D18, R57, and C35 and it is fed into the ISEN pin (#6) of L6599AT. In case of overcurrent, the voltage on the pin will exceed an internal threshold (0.8 V), triggering a protection sequence. The capacitor (C21) connected to the DELAY pin (#2) is charged by an internal 150 µA current generator. If the voltage on the pin reaches 2 V, the soft-start capacitor is completely discharged so that the switching frequency is pushed to its maximum value. As the voltage on the pin exceeds 3.5 V the IC stops switching and the internal generator is turned off, so that the voltage on the DELAY pin will decay because of the external resistor connected between the pin and GND. The L6599AT will be softrestarted as the voltage drops below 0.3 V. In this way, under short-circuit conditions, the converter will work intermittently with low input average power and thus limiting the stress of components during shorts. 1.6 Overvoltage and open loop protection Both circuit stages, PFC and resonant, are equipped with their own overvoltage protections. The PFC controller L6562AT implements an overvoltage protection against the output voltage variation occurring in case of transients, due to the poor bandwidth of the error amplifier. Unfortunately it cannot protect the circuit in case of a feedback loop failure like disconnection or deviation from the nominal value of the feedback loop divider. If a similar failure condition is detected, the L6599AT pin DIS (#8) stops the operation and also stops the PFC operation by means of the L6599AT pin PFC_STOP (#9) connected to the L6562AT pin INV (#1). The converter operation will be latched until the VCC capacitors are discharged, then a new startup sequence will automatically take place and the converter will resume operation if the failure is removed or a new sequence is triggered. The same sequence occurs also in case of input voltage transients that may damage the converter. The DIS pin is also used to protect the resonant stage against loop failures. The Zener diode D17 detects the auxiliary voltage generated by the LLC transformer. In case a loop failure occurs, it conducts and the voltage on pin DIS exceeds the internal threshold, latching off the device. The L6562AT operation will be stopped too by the PFC_STOP pin, like in the previous case and then after some time the circuit will restart. DocID016775 Rev 3 5/31 31 DocID016775 Rev 3 RX2 R47 VCC 1 R45 R14 R12 R7 2 D3 GBU8J 3 Q3 N. M. 2 VIN 1 C4 470 nF R44 N. M. ZCD GND GD VCC C31 220 nF R42 R8 R5 R49 R37 220 nF C9 10 nF 2 1 DELAY CSS HVG VBOOT L6599AT U2 R33 R23 1 D7 BZV55-B15 R11 3 D9 R21 LL414 8 1 C10 R52 D23/JPX9 JUMPER 3 C25 OUT CF 470 pF 4 RFMIN NC 5 STBY VCC 6 ISEN LVG 7 LINE GND 8 DIS PFC-STOP R32 R18 D8 LL4148 Q1 BC846C 2 D1 1N4007 D4 LL4148 L1 1975.0001 9 5 11 3 D5 LL4148 R3 D17 BZV55-B24 C33 C32 10 nF R43 R38 D14 LL4148 C26 4.7 nF R36 C21 220 nF R27 C13 R13 VCC 5 6 7 8 U1 L6562AT R16 R1 N.M. C24 MULT CS _ HS1 Heatsink COMP INV R15 C16 220 pF 4 3 2 1 D10 N. M. R20 3 Q7 1 BC846C 2 C15 4.7 nF C12 C11 470 nF PCB rev. 0.2 Z1 3 4 ~ C2 C3 470 nF - X2 470 nF - X2 1 Q8 2 BC846C 3 FUSE T4A RV 300 VAC F1 R22 85-305 VAC 3 2 1 L2 2019.0002 ~ 6/31 + J1 MKDS 1,5/ 3-5,08 R34 9 10 11 12 13 V CC 14 15 C22 100 nF 16 3 C30 Q2 2 STF22NM60N LL4148 D6 D2 STTH3L06U D24 LL4148 R39 R57 R46 1 1 R26 C7 C40 D19 LL4148 C34 220 pF R59 D20 STPS1L60A R53 3 Q4 STD10NM60N 2 Q5 3 STD10NM60N 2 C6 D18 LL4148 RX1 D13 LL4148 R25 R19 R17 VIN R24 R10 R4 D16 LL4148 C35 220 nF R9 R6 R2 C5 7 6 14 13 10 11 12 C27 220 nF REV 0.7 3 4 2 1 R62 470 nF C38 N. M. C39 R54 R60 R58 D15 BZV55-B24 Q6 BC846C 2 3 R41 C17 C18 1 R55 R51 N. M. R29 N. M. C41 N. M. R61 N. M. 3 2 1 Vctrl Ictrl OUT I.sense VCC GND 1 2 C36 N. M. C37 N. M. AM00883 4 5 6 48 V at 2.7 A 100 nF C19 J2 MKDS 1,5/ 2-5,08 U4 SEA05 - N.M. R56 N. M. R31 R30 D22 D21 BZV55-B24 BZV55-B24 L3 U5 TS2431AILT R50 D11 STPS10150CG D12 STPS10150CG U3 SFH617A-2X009 4 C20 15 nF T1 1860.0013 9 2 8 C8 2.2 nF - Y1 C1 2.2 nF - Y1 Main characteristics and circuit description AN3106 Figure 2. STEVAL-ILL053V1 evaluation board: electrical diagram AN3106 2 Efficiency measurement Efficiency measurement Table 1 shows the overall efficiency, measured at 230 V - 50 Hz and 115 V - 60 Hz input voltage and different loads. At 115 VAC and full load the overall efficiency is 90.96%. It increases up to 93.38% at 230 VAC, confirming that this reference design is suitable for high-efficiency power supplies. The efficiency has been measured at 25%, 50%, 75% and 100%, and the average efficiency according to the ES-2 standard has been calculated. As shown in Table 1 it is very high at both nominal mains. Table 1. STEVAL-ILL053V1 evaluation board: overall efficiency vs. load 230 V - 50 Hz 115 V - 60 Hz Load VOUT [V] IOUT [A] POUT [W] PIN [W] Eff. [%] VOUT [V] IOUT [A] POUT [W] PIN [W] Eff. [%] 25% load 47.58 0.689 32.8 37.87 86.57% 47.59 0.689 32.8 37.87 86.58% 50% load 47.57 1.378 65.6 71.66 91.48% 47.58 1.378 65.6 72.93 89.90% 75% load 47.56 2.008 95.5 102.96 92.75% 47.56 2.001 95.2 105.0 90.64% 100% load 47.55 2.708 128.8 137.6 93.38% 47.56 2.703 128.6 141.33 90.96% Average efficiency 91.04% 89.52% The measured output voltage at different load conditions is also shown in Table 1. As visible, the voltage is very stable over the entire output load range. The measured efficiency is shown in Figure 3, while Figure 4 shows the efficiency at maximum load over the entire AC input voltage mains range. Figure 4. STEVAL-ILL053V1 evaluation board: full-load efficiency vs. VAC           (IILFLHQF\DW9$& (IILFLHQF\DW9$&        (IILFLHQF\ (IILFLHQF\ Figure 3. STEVAL-ILL053V1 evaluation board: efficiency vs. load   /RDG    $0 DocID016775 Rev 3          9$&>9UPV@ $0 7/31 31 Input current harmonics measurement 3 AN3106 Input current harmonics measurement One of the main purposes of a PFC precondition is the correction of input current distortion, decreasing the harmonic contents below the limits of the relevant regulations. Therefore, this evaluation board has been tested according to the European norm EN61000-3-2 ClassC and Japanese norm JEITA_MITI Class-C both relevant to lighting equipment, at full load and nominal input voltage mains. The measurements are shown in Figure 5 and Figure 6. Figure 5. STEVAL-ILL053V1 evaluation board: compliance to EN61000-3-2 Class-C standard 0HDVXUHGYDOXH Figure 6. STEVAL-ILL053V1 evaluation board: compliance to JEITA-MITI Class-C standard 0HDVXUHGYDOXH (1&ODVV&OLPLWV +DUPRQLFFXUUHQW>$@ +DUPRQLFFXUUHQW>$@     -(,7$0,7,&ODVV&OLPLWV                                                +DUPRQLFRUGHU>Q@ +DUPRQLFRUGHU>Q@ VIN = 230 VAC - 50 Hz, PIN = 138.8 W THD = 8.70%, PF = 0.976 $0 VIN = 100 VAC - 50 Hz, PIN = 141.3 W THD = 3.31%, PF = 0.994 $0 For user reference, waveforms of the input current and voltage at nominal input voltage mains during full-load operation are shown in Figure 5 and Figure 6. Figure 7 and Figure 8 give the input current and voltage at nominal input voltage mains 50% load, showing that in spite of the wide input voltage range, the current waveform shape is still good. Figure 7. STEVAL-ILL053V1 evaluation board: input current waveform at 230 V - 50 Hz - 65 W load Figure 8. STEVAL-ILL053V1 evaluation board: input current waveform at 100 V - 50 Hz - 65 W load CH1: AC input mains voltage CH1: AC input mains voltage 8/31 CH4: AC input mains current DocID016775 Rev 3 CH4: AC input mains current AN3106 Input current harmonics measurement As confirmed by the previous graphs, the circuit also shows its ability to reduce the harmonics well below the limits of EN61000-3-2 Class-C regulation not only at full load but also at a significantly lower load. The input current harmonics measurement at 25 W (minimum input power to be compliant with the previously mentioned rules is 25 W) shows that even if the power supply is working from its typical operating region, it is still compliant with the EN61000-3-2 Class-C limits. Test results are shown in Figure 9 and Figure 10. Figure 9. STEVAL-ILL053V1 evaluation board: compliance to EN61000-3-2 Class-C standard 0HDVXUHGYDOXH Figure 10. STEVAL-ILL053V1 evaluation board: compliance to JEITA-MITI Class-C standard (1&ODVV&OLPLWV 0HDVXUHGYDOXH     -(,7$0,7,&ODVV&OLPLWV  +DUPRQLFFXUUHQW>$@ +DUPRQLFFXUUHQW>$@                       +DUPRQLFRUGHU>Q@                         +DUPRQLFRUGHU>Q@ $0 VIN = 230 VAC - 50 Hz, PIN = 25 W THD = 11.80%, PF = 0.697 $0 VIN = 100 VAC - 50 Hz, PIN = 25 W THD = 6.65%, PF = 0.92 The “Power Factor” (PF) and the “Total Harmonic Distortion” (THD) versus load variations have been measured too and the results are shown in Figure 11 and Figure 12. As visible, the Power Factor remains close to unity and the Total Harmonic Distortion is very low throughout the input voltage mains. Figure 11. STEVAL-ILL053V1 evaluation board: Figure 12. STEVAL-ILL053V1 evaluation board: Power Factor vs. output power Total Harmonic Distortion vs. output power 7+'YVORDG 3RZHU)DFWRUYVORDG       7+' 3RZHU)DFWRU   3)DW9$& 3)DW9$&    7+'DW9$& 7+'DW9$&       /RDG    $0 DocID016775 Rev 3   /RDG   $0 9/31 31 Functional check AN3106 4 Functional check 4.1 PFC circuit In Figure 13 and Figure 15 some waveforms relevant to the PFC stage have been captured during full load operation at nominal 230 VAC and 115 VAC. In both figures it is visible that the envelope of the CS pin (#4) waveforms of the L6562AT is in phase with the MULT pin (3#) and has same sinusoidal shape, demonstrating the proper functionality of the PFC stage. It is also possible to measure the peak-to-peak value of the voltage ripple superimposed on the PFC output voltage due to the low value of the PFC output capacitors. In Figure 14 and Figure 16 the details of some waveforms at the switching frequency are shown. Figure 13. STEVAL-ILL053V1 evaluation board: Figure 14. STEVAL-ILL053V1 evaluation board: PFC stage and L6562AT waveforms at 230 V - 50 PFC stage and L6562AT waveforms at 230 V - 50 Hz - full load Hz - full load - detail CH1: VOUT PFC CH2: MULT CH3: CS CH1: VOUT PFC CH2: MULT CH3: CS CH4: Vdrain_Q2 Figure 15. STEVAL-ILL053V1 evaluation board: Figure 16. STEVAL-ILL053V1 evaluation board: PFC stage and L6562AT waveforms at 115 V - 60 PFC stage and L6562AT waveforms at 115 V - 60 Hz - full load Hz - full load - detail CH1: VOUT PFC 10/31 CH2: MULT CH3: CS CH1: VOUT PFC DocID016775 Rev 3 CH2: MULT CH3: CS CH4: Vdrain_Q2 AN3106 4.2 Functional check Half-bridge resonant LLC circuit The following figures show waveforms relevant to the resonant stage during steady-state operation. The resonant stage switching frequency is about 100 kHz, in order to have a good trade-off between transformer losses and dimensions. The LLC converter has been designed to operate at nominal voltage and full load at the resonance frequency, but due to the PFC output voltage ripple at twice the mains frequency, it is driven slightly above and below the resonant tank frequency, according to the instantaneous value of the PFC output voltage. In Figure 17 some waveforms relevant to the resonant stage ZVS operation are shown. We note that both MOSFETs are turned on when resonant current is flowing through their body diodes and drain-source voltage is almost zero, thus achieving good efficiency because the turn-on losses are negligible. The HB MOSFET voltage de-rating and low operating temperature allow increasing the board’s MTBF. The current flowing in the resonant tank is sinusoidal. In Figure 17 we note a slight asymmetry of operating modes by each half portion of the sine wave. The half cycle is working at resonant frequency while the other one is working above the resonant frequency. This is due to a small difference between each half-secondary leakage inductance of the transformer reflected to the primary side, providing the two slightly different resonant frequencies. This phenomenon is typically due to a different coupling of the transformer secondary windings and, in this case, it is not an issue. The slight asymmetry is also visible in Figure 18 where the small ringing appearing on both secondary rectifiers anode voltage indicates that for a short time the rectifiers are not conducting. This demonstrates that during the half cycle the circuit is working below the resonant frequency, while during the following half cycle it is working at the resonant frequency. In Figure 18 we also note the rectifier operating voltage and its margin with respect to the maximum reverse voltage (VRRM). This de-rating with respect to the rectifiers VRRM guarantees good reliability of the output rectifiers, increasing the board’s total MTBF. Figure 17. STEVAL-ILL053V1 evaluation board: Figure 18. STEVAL-ILL053V1 evaluation board: primary side LLC waveforms at 115 V - 60 Hz - secondary side LLC waveforms at 230 V- 50 Hz full load full load CH1: HB voltage CH3: VCC CH2: CF pin voltage CH4: res. tank current CH1: V_D12 CH3: VOUT DocID016775 Rev 3 CH2: V_D12 11/31 31 Functional check AN3106 In Figure 19 the high-frequency ripple has been measured. As visible the ripple and noise at switching frequency is very limited, thanks to the low EMI generated by both stages. In Figure 20 the low-frequency ripple has been measured too. We note that the peak-to-peak value is not very low because of the low output capacitances but it doesn't affect the application. In fact the converters regulating the current flowing in each LED strip can reject the ripple without any problem. Figure 19. STEVAL-ILL053V1 evaluation board: Figure 20. STEVAL-ILL053V1 evaluation board: high frequency ripple on output voltage at 115 V low frequency ripple on output voltage at 115 V - 60 Hz - full load - 60 Hz - full load CH3: VOUT 4.3 CH3: VOUT Dynamic load operation The waveforms shown in Figure 21 and Figure 22 pertain to the evaluation board during the operation of supplying converters dedicated to power LED strips with constant current. In both figures it is possible to see the output voltage modulation during operation with variable load due to the dimming of the LED current by PWM. For both measurements, the dimming frequency has been chosen at 300 Hz, a typical value for dimming. In Figure 21 the converter’s output current was 2.6 A and the dimming duty cycle was 90%, thus very close to the converter’s nominal output power. The output voltage has two modulations. One is due to the rejection of the PFC output voltage ripple already measured in Figure 20 where the voltage variation due to the LED current dimming is superimposed. The peak-to-peak variation is 5.37 V but it doesn't present any problem for the load since the converters reject the modulation. In Figure 22 instead the converter has been checked at light load, so the peak output current was 3 A and the dimming duty cycle was 15%, for an output power of 21 W. Even in this case, the peak-to peak modulation doesn't present any issue for the downstream current regulators and the board still works correctly. 12/31 DocID016775 Rev 3 AN3106 Functional check Figure 21. STEVAL-ILL053V1 evaluation board: Figure 22. STEVAL-ILL053V1 evaluation board: output voltage variation driving a CC LED output voltage variation driving a CC LED converter - PWM = 90% converter - PWM = 15% CH1: PWM dimming signal CH4: SMPS output current CH2: VOUT CH1: PWM dimming signal CH4: SMPS output current CH2: VOUT Please note that for correct operation with LED strips, the board needs additional capacitors connected on the +48 V output bus. The board has not been equipped with all of the capacitors necessary for correct operation with LEDs, but only with minimum capacitance to allow board operation in order to optimize the system cost and reliability. The additional capacitors needed are intended to be placed close to each LED strip current regulator, thus filtering the EMI generated by these. In several cases, in fact, the power supply is placed at the base of the lighting pole while the LED current regulators are located on top, in the lamp. The long connection wiring between the power supply and the converters can act as an antenna radiating EMI. Thus local filtering minimizes the radiated EMI. The capacitance to be added to the 48 V bus for correct operation with LEDs is around 40 µF. In order to not affect the board MTBF, we suggest using the same type of capacitors already used on the power supply board. 4.4 Overcurrent and overvoltage protection The L6599AT is equipped with a current sensing input (pin #6, ISEN) and a dedicated overcurrent management system. The current flowing in the resonant tank is detected and the signal is fed into the ISEN pin. It is internally connected to a first comparator, referenced to 0.8 V, and to a second comparator referenced to 1.5 V. If the voltage externally applied to the pin exceeds 0.8 V, the first comparator is tripped, causing an internal switch to be turned on and discharging the soft-start capacitor C24 (CSS). Under output short-circuit, this operation results in a nearly constant peak primary current. With the L6599AT the designer can program externally the maximum time that the converter is allowed to run overloaded or under short-circuit conditions. Overloads or short-circuits lasting less than the set time will not cause any other action, hence providing the system with immunity to short duration phenomena. If, instead, the overload condition persists, a protection procedure is activated that shuts down the L6599AT. In case of continuous overload or short-circuit, it will result in continuous intermittent operation with a user-defined duty cycle. DocID016775 Rev 3 13/31 31 Functional check AN3106 This function is implemented with the DELAY pin (#2), by means of a capacitor C21 and the parallel resistor R32 connected to ground. As the voltage on the ISEN pin exceeds 0.8 V, the first OCP comparator, in addition to discharging CSS, turns on an internal 150 µA current generator that via the DELAY pin charges C21. As the voltage on C21 is 3.5 V, the L6599AT stops switching and the PFC_STOP pin (#9) is pulled low, turning off also the PFC stage via the L6562AT pin#1 (INV). The internal generator is also turned off, so that C21 will now be slowly discharged by R32. The IC will restart once the voltage on C21 is less than 0.3 V. Additionally, if the voltage on the ISEN pin reaches 1.5 V for any reason (e.g. transformer saturation), the second comparator will be triggered, the L6599AT will shut down and the operation will be resumed after recycling of the VCC. In this evaluation board the intervention of the second level comparator will latch the operation of the L6599AT and the PFC_STOP pin (#9) will stop the PFC. Both controllers will no longer be powered by VCC and the latch will be removed and then a new startup cycle will take place. This sequence continues until the short is removed. Figure 23 shows the operation of the DELAY pin and the consequent hiccup mode operation of the board during short-circuit operation. Thanks to the narrow operating time with respect to the off-time, the average output current as well as the average primary current are limited. This will avoid converter overheating and consequent failures. Removing the short allows the board to resume normal operation. Figure 23. STEVAL-ILL053V1 evaluation board: Figure 24. STEVAL-ILL053V1 evaluation board: short-circuit at 115 VAC - 60 Hz - full load open loop at 115 VAC - 60 Hz - 65 W load CH1: V_OUT_PFC CH3: DELAY pin CH2: HB voltage CH4: U1 pin INV CH1: Q1_Drain CH3: VOUT CH2: HB voltage CH4: DIS pin Figure 24 shows the operation of the evaluation board during “open loop” operation by the LLC stage. The open loop operation provides an increase also of the auxiliary voltage that will trigger the L6599AT pin #9 (DIS) protection pin via the Zener diode D17. As a consequence, the L6599AT will shut down, stopping the operation. The L6599AT will activate also the PFC_STOP pin (#9) that will stop the PFC too, thus both controllers will no longer be powered by VCC. Once VCC drops below the UVLO, the latch is removed and then a new startup cycle will take place. This sequence continues until the open loop is removed. 4.5 Converter startup Figure 25 and Figure 27 show the converter startup. We note that at 115 VAC the converter begins operation in ~300 ms, while at 230 VAC it takes around 150 ms. This is the time 14/31 DocID016775 Rev 3 AN3106 Functional check needed to charge the VCC to the L6562AT turn-on voltage. Thus the L6562AT starts switching and the PFC output voltage starts increasing. Once the PFC output voltage reaches the enable level set via the L6599AT LINE pin, even the LLC stage starts switching and the output voltage rises up to the nominal level. The VCC is initially supplied by the PFC coil charge pump, and then once the L6599AT starts operating, the VCC is also provided by the LLC transformer auxiliary winding. The details of converter sequencing can be found in Figure 26 and Figure 28. Figure 25. STEVAL-ILL053V1 evaluation board: Figure 26. STEVAL-ILL053V1 evaluation board: wake-up at 115 VAC - 60 Hz - full load sequencing at 115 VAC - 60 Hz - full load CH1: Q2_Drain CH3: L6562AT VCC CH2: HB voltage CH4: VOUT CH1: Q2_Drain CH3: L6599AT VCC pin CH2: HB voltage CH4: VOUT Figure 27. STEVAL-ILL053V1 evaluation board: Figure 28. STEVAL-ILL053V1 evaluation board: wake-up at 230 VAC - 50 Hz - full load sequencing at 230 VAC - 60 Hz - full load CH1: Q2_Drain CH3: L6562AT VCC CH2: HB voltage CH4: VOUT CH1: Q2_Drain CH3: L6599AT VCC pin CH2: HB voltage CH4: VOUT Figure 25 through 28 show a correct startup of the board using an active load, with only the capacitors for the 48 V populating the board. Powering current regulators with LEDs may cause the board to show an incorrect startup, with output voltage going up and down and LEDs flashing. As already explained in Section 4.3, the board needs an additional 40 µF capacitance on the +48 V. DocID016775 Rev 3 15/31 31 Thermal map 5 AN3106 Thermal map In order to check the design reliability, a thermal mapping by means of an IR camera was done. Here below the thermal measures of the board, component side, at nominal input voltage are shown. Some pointers visible on the pictures have been placed across key components or components showing high temperature. The ambient temperature during both measurements was 27 °C. We note that the PFC part has a different temperature depending on the input mains, while the components of the resonant stage are working at a temperature independent of the mains input voltage. Figure 29. Thermal map at 115 VAC - 60 Hz - full load - PCB top side Figure 30. Thermal map at 230 VAC - 50 Hz - full load - PCB top side Table 2. Thermal maps reference points - PCB top side 16/31 Point Reference Description A L2 EMI filtering inductor B D3 Bridge rectifier C Q2 PFC MOSFET D L1 PFC inductor E T1 Resonant power transformer - winding F T1 Resonant power transformer - ferrite core DocID016775 Rev 3 AN3106 Thermal map Figure 31. Thermal map at 115 VAC - 60 Hz - full load - PCB bottom side Figure 32. Thermal map at 230 VAC - 50 Hz - full load - PCB bottom side Table 3. Thermal maps reference points - PCB bottom side Point Reference Description A Q4 LLC resonant HB MOSFET B Q5 LLC resonant HB MOSFET C D2 PFC output diode D R33 and R34 PFC sense resistors E Q1 VCC voltage regulator F D12 Output rectifier G D11 Output rectifier DocID016775 Rev 3 17/31 31 Conducted emission precompliance measurement 6 AN3106 Conducted emission precompliance measurement Figure 33 to Figure 36 show the average measurement of the conducted noise at full load and nominal mains voltages for both wires, line and neutral. The limits on the diagrams are the EN55022 Class-B norms. As visible on the diagrams, in all test conditions the measurements are well below the limits. Figure 33. CE average measurement at 115 VAC and full load - phase wire Figure 34. CE average measurement at 115 VAC and full load - neutral wire 18/31 DocID016775 Rev 3 AN3106 Conducted emission precompliance measurement Figure 35. CE average measurement at 230 VAC and full load - phase wire Figure 36. CE average measurement at 230 VAC and full load - neutral wire DocID016775 Rev 3 19/31 31 Bill of material 7 AN3106 Bill of material Table 4. STEVAL-ILL053V1 evaluation board: bill of material Des. Part type / part value Case style / package Description Supplier C1 2.2 nF - Y1 4.5 x 12.0 p.10 mm Y1 safety cap. DE1E3KX222M Murata C10 1 µF 1206 50 V CERCAP - general purpose - X7R- 10% TDK© C11 470 nF 0805 16 V CERCAP - general purpose - X7R - 10% Murata C12 2.2 µF 0805 10 V CERCAP - general purpose AVX C13 10 µF 1210 25 V-X7R CERCAP - gen. purpose - X7R - 20% TDK C15 4.7 nF 0805 50 V CERCAP - general purpose - X7R - 10% KEMET C16 220 pF 0805 50 V CERCAP - general purpose - C0G - 5% KEMET C17 4.7 µF 7.8 x 7.8 p. 5 63 V - MKT film cap. - B32529D0475M000 EPCOS C18 4.7 µF 7.8 x 7.8 p. 5 63 V - MKT film cap. - B32529D0475M000 EPCOS C19 100 nF 0805 100 V CERCAP - general purpose - X7R - 10% AVX C2 470 nF - X2 9 × 18.0 p.15 mm X2 - MKP film cap. - B32922C3474K EPCOS C20 15 nF 5 x 18 p.15 mm 1000 V - MKP film cap. - B32652A0153K000 EPCOS C21 220 nF 0805 16 V CERCAP - general purpose - X7R - 10% Murata C22 100 nF 1206 50 V CERCAP - general purpose - X7R - 10% KEMET C24 4.7 µF 0805 6.3 V CERCAP - general purpose - X5R - 10% EPCOS C25 470 pF 0805 50 V CERCAP - general purpose - COG - 5% EPCOS C26 4.7 nF 0805 50 V CERCAP - general purpose - X7R - 10% KEMET C27 220 nF 0805 50 V CERCAP - general purpose - X7R - 10% Murata C3 470 nF - X2 9 × 18.0 p.15 mm X2 - MKP film cap. - B32922C3474K EPCOS C30 10 µF 1210 25 V CERCAP - general purpose - X7R - 20% TDK C31 220 nF 0805 16 V CERCAP - general purpose - X7R - 10% Murata C32 220 nF 0805 16 V CERCAP - general purpose - X7R - 10% Murata C33 10 nF 0805 50 V CERCAP - general purpose - X7R - 10% KEMET C34 220 pF 1206 1 KV high voltage CERCAP - X7R - 10% AVX C35 220 nF 0805 16 V CERCAP - general purpose - X7R - 10% Murata C36 N. M. 0805 Not mounted C37 N. M. 0805 Not mounted C38 N. M. 0805 Not mounted 20/31 DocID016775 Rev 3 AN3106 Bill of material Table 4. STEVAL-ILL053V1 evaluation board: bill of material (continued) Des. Part type / part value Case style / package Description Supplier C39 470 nF 0805 25 V CERCAP - general purpose - X7R - 10% KEMET C4 470 nF 9 × 18.0 p.15 mm X2 - MKP film cap. -B32922C3474K EPCOS C40 10 µF 2220 50 V - CERCAP - general purpose - X7R - 20% TDK C41 N. M. 0805 Not mounted C5 5 µF 14 × 31.5 p. 27.5 mm 800 V - MKP film cap. - B32774D8505K000 EPCOS C6 5 µF 14 × 31.5 p. 27.5 mm 800 V - MKP film cap. - B32774D8505K000 EPCOS C7 5 µF 14 × 31.5 p. 27.5mm 800 V - MKP film cap. - B32774D8505K000 EPCOS C8 2.2 nF - Y1 4.5 x 12 p.10 mm Y1 safety cap. DE1E3KX222M Murata C9 10 nF 1206 100 V CERCAP - gen. purpose - X7R - 10% KEMET D1 1.4007 nF DO-41 General purpose rectifier VISHAY® D10 N. M. SOD-80 Zener diode D11 STPS10150CG D2PAK Power Schottky rectifier STMicroelectronics D12 STPS10150CG D2PAK Power Schottky rectifier STMicroelectronics D13 LL4148 SOD-80 Fast switching diode VISHAY D14 LL4148 SOD-80 Fast switching diode VISHAY D15 BZV55-B24 SOD-80 Zener diode VISHAY D16 LL4148 SOD-80 Fast switching diode VISHAY D17 BZV55-B24 SOD-80 Zener diode VISHAY D18 LL4148 SOD-80 Fast switching diode VISHAY D19 LL4148 SOD-80 Fast switching diode VISHAY D2 STTH3L06U SMB Ultrafast high voltage rectifier STMicroelectronics D20 STPS1L60A SMA Fast switching diode STMicroelectronics D21 BZV55-B24 SOD-80 Zener diode VISHAY D22 BZV55-B24 SOD-80 Zener diode VISHAY JPX9 /D23 Jumper D24 LL4149 SOD-81 Fast switching diode VISHAY D3 GBU8J STYLE GBU DWG Single phase bridge rectifier VISHAY D4 LL4148 SOD-80 Fast switching diode VISHAY D5 LL4148 SOD-80 Fast switching diode VISHAY Wire jumper DocID016775 Rev 3 21/31 31 Bill of material AN3106 Table 4. STEVAL-ILL053V1 evaluation board: bill of material (continued) Des. Part type / part value Case style / package Description Supplier D6 LL4148 SOD-80 Fast switching diode VISHAY D7 BZV55-B15 SOD-80 Zener diode VISHAY D8 LL4148 SOD-80 Fast switching diode VISHAY D9 LL4148 SOD-80 Fast switching diode VISHAY F1 FUSE T4A 8.5 x 4 p. 5.08 mm Fuse 4 A - time lag - 3921400 LITTLEFUSE HS1 Heatsink DWG Heatsink for D3 and Q2 J1 MKDS 1,5 / 3-5,08 p. 5.08 mm PCB term. block, screw conn., pitch 5 MM - 3 W. PHOENIX CONTACT J2 MKDS 1,5 / 2-5,08 p. 5.08 mm PCB term. block, screw conn., pitch 5 MM - 2 W. PHOENIX CONTACT L1 1975.0001 DWG PFC choke - 520 µH PQ26/25 MAGNETICA L2 12 mH DWG CM filter 2019.0002 MAGNETICA L3 3.3 µH - 4.7 A DIA. 7.7 p. 5 mm Inductor 1071.0080 MAGNETICA Q1 BC846C SOT-23 NPN small signal BJT VISHAY Q2 STF22NM60N TO220 N-channel Power MOSFET STMicroelectronics Q3 N. M. SOT-23 PNP small signal BJT Q4 STD10NM60N DPAK N-channel Power MOSFET STMicroelectronics Q5 STD10NM60N DPAK N-channel Power MOSFET STMicroelectronics Q6 BC846C SOT-23 NPN small signal BJT VISHAY Q7 BC846C SOT-23 NPN small signal BJT VISHAY Q8 BC846C SOT-23 NPN small signal BJT VISHAY R1 N. M. 0805 Not mounted R10 1.2 MΩ 1206 SMD standard film res. - 1/4 W - 1% - 100 ppm / °C VISHAY R11 4.7 KΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R12 2.0 MΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R13 120 KΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R14 390 KΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R15 39 KΩ 0805 SMD standard film res. - 1/8 W - 1% - 100 ppm / °C VISHAY R16 39 KΩ 0805 SMD standard film res. - 1/8 W - 1% - 100 ppm / °C VISHAY R17 0Ω 1206 SMD standard film res. - 1/4 W - 1% - 100 ppm / °C VISHAY R18 56 KΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R19 0Ω 0805 SMD standard film res. - 1/8 W - 1% - 100 ppm / °C VISHAY R2 1 MΩ 1206 SMD standard film res. - 1/4 W - 1% - 100 ppm / °C VISHAY R20 120 KΩ 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R21 33 Ω 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY 22/31 DocID016775 Rev 3 AN3106 Bill of material Table 4. STEVAL-ILL053V1 evaluation board: bill of material (continued) Des. Part type / part value Case style / package Description Supplier R22 39 KΩ 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R23 100 Ω 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R24 1.4 MΩ 1206 SMD standard film res.- 1/4 W - 1% - 100 ppm / °C VISHAY R25 82 KΩ 0805 SMD standard film res.- 1/8 W - 1% - 100 ppm / °C VISHAY R26 15 KΩ 0805 SMD standard film res. - 1/8 W - 1% - 100 ppm / °C VISHAY R27 470 Ω 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R29 N. M. 1206 Not mounted R3 10 Ω 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R30 0Ω 1206 SMD standard film res.- 1/8 W - 1% - 100 ppm / °C VISHAY R31 0Ω 1206 SMD standard film res. - 1/8 W - 1% - 100 ppm/ °C VISHAY R32 270 KΩ 0805 SMD standard film res.- 1/8 W - 5% - 250 ppm / °C VISHAY R33 0.39 Ω 2010 SMD standard film res. - 1/2 W - 5% - 250 ppm / °C VISHAY R34 0.39 Ω 2010 SMD standard film res. - 1/2 W - 5% - 250 ppm / °C VISHAY R36 4.7 KΩ 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R37 6.8 KΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R38 2.2 MΩ 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R39 51 Ω 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R4 1.2 MΩ 1206 SMD standard film res. - 1/4 W - 1% - 100 ppm / °C VISHAY R41 4.7 KΩ 1206 SMD standard film res.- 1/4 W - 5% - 250 ppm / °C VISHAY R42 10 KΩ 0805 SMD standard film res. - 1/8 W - 1% - 100 ppm / °C VISHAY R43 10 KΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R44 N. M. 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C R45 220 KΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R46 51 Ω 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R47 220 KΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R49 0Ω 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R5 120 KΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R50 10 KΩ 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R51 N. M. 0805 Not mounted R52 10 Ω 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R53 100 RΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R54 2.2 KΩ 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R55 470 Ω 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R56 N. M. 0805 Not mounted DocID016775 Rev 3 23/31 31 Bill of material AN3106 Table 4. STEVAL-ILL053V1 evaluation board: bill of material (continued) Des. Part type / part value Case style / package Description Supplier R57 100 Ω 0805 SMD standard film res.- 1/8 W - 5% - 250 ppm / °C VISHAY R58 150 KΩ 0805 SMD standard film res. - 1/8 W - 1% - 100 ppm / °C VISHAY R59 1.5 Ω 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R6 1.0 MΩ 1206 SMD standard film res.- 1/4 W - 1% - 100 ppm / °C VISHAY R60 8.2 KΩ 0805 SMD standard film res.- 1/8 W - 1% - 100 ppm / °C VISHAY R61 N. M. 1206 Not mounted R62 100 KΩ 0805 SMD standard film res. - 1/8 W - 5% - 250 ppm / °C VISHAY R7 2.0 MΩ 1206 SMD standard film res. - 1/4W - 5% - 250 ppm/ °C VISHAY R8 120 KΩ 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY R9 1.5 MΩ 1206 SMD standard film res. - 1/4 W - 1% - 100 ppm / °C VISHAY RV1 300 VAC dia. 15 x 5 p. 7.5 mm 300 V metal oxide varistor - B72214S0301K101 EPCOS RX1 0Ω 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY RX2 0Ω 1206 SMD standard film res. - 1/4 W - 5% - 250 ppm / °C VISHAY T1 1860.0013 DWG ETD34 Resonant power transformer MAGNETICA U1 L6562ATD SO-8 TM PFC controller STMicroelectronics U2 L6599ATD SO-16 Improved HV resonant controller STMicroelectronics U3 SFH617A-2X009 SMD4 10.16 mm Optocoupler VISHAY U4 SEA05 - N. M. SOT-23-6L CC/CV controller – not mounted STMicroelectronics U5 TS2431AILT SOT-23 Programmable shunt voltage reference STMicroelectronics Z1 PCB rev. 0.2 24/31 DocID016775 Rev 3 AN3106 8 PFC coil specifications PFC coil specifications General description and characteristics • Application type: consumer, home appliance • Transformer type: open • Coil former: vertical type, 6 + 6 pins • Max. temp. rise: 45 °C • Max. operating ambient temperature: 60 °C • Mains insulation: N. A. • Unit finishing: varnished Electrical characteristics • Converter topology: boost, transition mode • Core type: PQ26/25-PC44 or equivalent • Min. operating frequency: 30 kHz • Typical operating frequency: 120 kHz • Primary inductance: 0.52 mH ± 10% at 1 kHz - 0.25 V, measured between pins #5 and #9 • Peak primary current: 4.3 Apk • RMS primary current: 1.8 ARMS Electrical diagram and winding characteristics Figure 37. PFC coil electrical diagram     $0 DocID016775 Rev 3 25/31 31 PFC coil specifications AN3106 Table 5. PFC coil winding data Pins Windings Number of turns Wire type 11 - 3 Aux. 6 0.28 mm - G2 5-9 Primary 62 Multistrand #7x 0.28 mm - G2 • Primary winding external insulation: 2 layers of polyester tape • Aux. winding is wound on top of primary winding • External insulation: 2 layers of polyester tape • Wire connected to pin 5 is insulated by sleeve Mechanical aspect and pin numbering 26/31 • Maximum height from PCB: 29 mm • Coil former type: vertical, 6 + 6 pins (pins #1, 2, 4, 6, 7, 10, 12 are removed) • Pin distance: 3.81 mm • Row distance: 25 mm • Coil former P/N: TDK BPQ26/25-1112CP • External copper shield: not insulated, wound around the ferrite core and including the coil former. Height is 8 mm. Connected to pin #3 by a soldered solid wire. DocID016775 Rev 3 AN3106 PFC coil specifications Figure 38. PFC coil mechanical aspect PD[ PD[ PD[                  %RWWRPYLHZ SLQVLGH $0 1. Quotes are in millimeters, drawing is not to scale. Manufacturer • MAGNETICA di R. Volpini - Italy (www.magneticait.it) • Inductor P/N: 1975.0001. DocID016775 Rev 3 27/31 31 Transformer specifications 9 AN3106 Transformer specifications General description and characteristics • Application type: consumer, home appliance • Transformer type: open • Coil former: horizontal type, 7 + 7 pins, two slots • Max. temp. rise: 45 °C • Max. operating ambient temperature: 60 °C • Mains insulation: acc. with EN60950 Electrical characteristics • Converter topology: half-bridge, resonant • Core type: ETD34-PC44 or equivalent • Min. operating frequency: 70 kHz • Typical operating frequency: 100 kHz • Primary inductance: 770 µH ± 15% at 1 kHz - 0.25 V(a) • Leakage inductance: 170 µH at 100 kHz - 0.25 V(b) Electrical diagram and winding characteristics Figure 39. Transformer electrical diagram  35,0   $8;   6(&$   6(&%  $0 Table 6. Transformer winding data Pins Winding RMS current Number of turns Wire type 2-4 Primary 1 ARMS 47 #30 x 0.1 mm - G2 8-10 Sec. - A(1) 0.05 ARMS 9 #60 x 0.1 mm - G2 12-14 B4(1) 2.2 ARMS 9 #60 x 0.1 mm - G2 2.2 ARMS 3 0.28 mm - G2 6-7 Sec. - Aux.(2) 1. Secondary windings A and B have to be wound in parallel. 2. Aux. winding is wound on top of primary winding, turns are close each other, placed on external side of the coil former. a. Measured between pins 2-4. b. Measured between pins 2-4 with only one secondary winding shorted. Difference between the two measured leakage inductances has to be < 10%. 28/31 DocID016775 Rev 3 AN3106 Transformer specifications Mechanical aspect and pin numbering • Maximum height from PCB: 30 mm • Coil former type: horizontal, 7 + 7 pins (pins #1, #3 and #5 removed for PCB reference) • Pin distance: 5.08 mm • Row distance: 25.4 mm Figure 40. Transformer mechanical aspect PD[ PD[ PLQ  PD[ /$%(/ 0LVVLQJ3,1DQG DV3&%UHIHUHQFH  3,1VLGHYLHZ                            $0 1. Quotes are in millimeters, drawing is not to scale. Manufacturer • MAGNETICA di R. Volpini - Italy (www.magneticait.it) • Transformer P/N: 1860.0013. DocID016775 Rev 3 29/31 31 Revision history 10 AN3106 Revision history Table 7. Document revision history 30/31 Date Revision Changes 01-Sep-2010 1 Initial release. 28-Sep-2012 2 – Modified: Figure 2 – Modified: Table 4 – Minor text changes to improve readability 13-May-2016 3 – Updated: Figure 1 on the cover page DocID016775 Rev 3 AN3106 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved DocID016775 Rev 3 31/31 31
EVL130W-STRLIG 价格&库存

很抱歉,暂时无法提供与“EVL130W-STRLIG”相匹配的价格&库存,您可以联系我们找货

免费人工找货