M74HC04TTR

M74HC04 Hex inverter Datasheet - production data Description The M74HC04 is a high-speed CMOS hex inverter manufactured using silicon gate C2MOS technology. DIP14 SO14 TSSOP14 Features The internal circuit is composed of 3 stages including a buffer output which enables high noise immunity and stable output. All inputs are equipped with protection circuits to guard against static discharge and transient excess voltage.  High speed: tPD = 8 ns (typ.) at VCC = 6 V  Low power dissipation: ICC = 1 μA (max.) at TA = 25 °C  High noise immunity: VNIH = VNIL = 28% VCC (min.)  Symmetrical output impedance: |IOH| = IOL = 4 mA (min) at VCC = 4.5 V  Balanced propagation delays: tPLH @ tPHL  Wide operating voltage range: VCC (OPR) = 2 V to 6 V  Pin and function compatible with 74 series 04  ESD performance – CDM: 1 kV – HBM: 2 kV – MM: 200 V Table 1. Device summary Order code Temperature range Package Packaging Marking M74HC04B1R -55 °C to +125 °C DIP14 Tube M74HC04B1 M74HC04YRM13TR(1) -40 °C to +125 °C SO14 (automotive grade) Tape and reel 74HC04Y M74HC04RM13TR -55 °C to +125 °C SO14 Tape and reel 74HC04 M74HC04TTR -55 °C to +125 °C TSSOP14 Tape and reel HC04 -40 °C to +125 °C TSSOP14 (automotive grade) Tape and reel HC04Y M74HC04YTTR (1) 1. Qualification and characterization according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 and Q002 or equivalent. September 2013 This is information on a product in full production. DocID001882 Rev 3 1/13 www.st.com Contents M74HC04 Contents 1 Pin information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 2/13 4.1 DIP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.2 SO14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.3 TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 DocID001882 Rev 3 M74HC04 1 Pin information Pin information Figure 1. Pin connections and IEC logic symbols Table 2. Pin description Pin number Symbol Name and function 1, 3, 5, 9, 11, 13 1A to 6A Data inputs 2, 4, 6, 8, 10, 12 1Y to 6Y Data outputs 7 GND Ground (0 V) 14 VCC Positive supply voltage DocID001882 Rev 3 3/13 13 Functional description 2 M74HC04 Functional description Table 3. Truth table A Y L H H L Figure 2. Input and output equivalent circuit 4/13 DocID001882 Rev 3 M74HC04 3 Electrical characteristics Electrical characteristics Stressing the device above the ratings listed in the “Absolute maximum ratings” table may cause permanent damage to the device. These are stress ratings only, and operation of the device at these or any other conditions above those indicated in the operating sections of this specification are not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 4. Absolute maximum ratings Symbol VCC Parameter Supply voltage Value Unit -0.5 to +7 V VI DC input voltage -0.5 to VCC +0.5 V VO DC output voltage -0.5 to VCC +0.5 V IIK DC input diode current ±20 mA IOK DC output diode current ±20 mA IO DC output current ±25 mA DC VCC or ground current ±50 mA 500(1) mW -65 to +150 °C 300 °C ICC or IGND PD Power dissipation Tstg Storage temperature TL Lead temperature (10 sec) 1. 500 mW at 65 °C; derate to 300 mW by 10 mW/°C from 65 °C to 85 °C Table 5. Recommended operating conditions Symbol VCC Parameter Supply voltage Value Unit 2 to 6 V VI Input voltage 0 to VCC V VO Output voltage 0 to VCC V Top Operating temperature -55 to 125 °C VCC = 2.0 V 0 to 1000 ns VCC = 4.5 V 0 to 500 ns VCC = 6.0 V 0 to 400 ns tr, tf Input rise and fall time DocID001882 Rev 3 5/13 13 Electrical characteristics M74HC04 Table 6. DC specifications Test condition Symbol VIH VIL VOH VOL Parameter High-level input voltage Low-level input voltage High-level output voltage Low-level output voltage Value TA = 25°C VCC (V) Min. Typ. -40 to 85°C -55 to 125°C Min. Min. Unit Max. Max. 2.0 1.5 1.5 1.5 4.5 3.15 3.15 3.15 6.0 4.2 4.2 4.2 Max. V 2.0 0.5 0.5 0.5 4.5 1.35 1.35 1.35 6.0 1.8 1.8 1.8 2.0 IO = -20 μA 1.9 2.0 1.9 1.9 4.5 IO = -20 μA 4.4 4.5 4.4 4.4 6.0 IO = -20 μA 5.9 6.0 5.9 5.9 4.5 IO = -4.0 mA 4.18 4.31 4.13 4.10 6.0 IO = -5.2 mA 5.68 5.8 5.63 5.60 2.0 IO = 20 μA 0.0 0.1 0.1 0.1 4.5 IO = 20 μA 0.0 0.1 0.1 0.1 6.0 IO = 20 μA 0.0 0.1 0.1 0.1 4.5 IO = 4.0 mA 0.17 0.26 0.33 0.40 6.0 IO = 5.2 mA 0.18 0.26 0.33 0.40 V V V II Input leakage current 6.0 VI = VCC or GND 0.1 1 1 μA ICC Quiescent supply current 6.0 VI = VCC or GND 1 10 20 μA 6/13 DocID001882 Rev 3 M74HC04 Electrical characteristics Table 7. AC electrical characteristics (CL = 50 pF, input tr = tf = 6 ns) Test condition Symbol tfLH tfHL tPLH tPHL Parameter TA = 25°C VCC (V) Output transition time Propagation delay time Value Min. -40 to 85°C -55 to 125°C Min. Min. Unit Typ. Max. Max. Max. 2.0 38 75 95 110 4.5 8 15 19 22 6.0 6 13 16 19 2.0 45 95 120 145 4.5 9 19 24 29 6.0 8 16 20 25 ns ns Table 8. Capacitive characteristics Test condition Symbol Parameter VCC (V) Value TA = 25°C Min. Max. 10 Input capacitance 5.0 5 CPD Power dissipation capacitance(1) 5.0 22 -55 to 125°C Min. Min. Unit Typ. CIN -40 to 85°C Max. 10 Max. 10 pF pF 1. CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to the test circuit). Average operating current can be obtained by the following equation: ICC(opr) = CPD x VCC x fIN + ICC/6 (per gate) DocID001882 Rev 3 7/13 13 Electrical characteristics M74HC04 Figure 3. Test circuit Figure 4. Waveforms: propagation delay times (f = 1 MHz; 50% duty cycle) 8/13 DocID001882 Rev 3 M74HC04 4 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 4.1 DIP14 package information Figure 5. Plastic DIP14 package mechanical outline Table 9. Plastic DIP14 package mechanical data mm. inches Dimension Min. a1 0.51 B 1.39 Typ Max. Min. Typ. Max. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L Z 3.3 1.27 0.130 2.54 DocID001882 Rev 3 0.050 0.100 9/13 13 Package information 4.2 M74HC04 SO14 package information Figure 6. Plastic SO14 package mechanical outline Table 10. SO14 package mechanical data mm. inches Ref. Min. Typ A a1 Max. Typ. 1.75 0.1 Max. 0.068 0.2 a2 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 10/13 Min. 0.68 0.026 8° (max.) DocID001882 Rev 3 M74HC04 4.3 Package information TSSOP14 package information Figure 7. TSSOP14 package mechanical outline Table 11. TSSOP14 package mechanical data Ref. mm. Min. Typ A inches Max. Min. Typ. 1.2 A1 0.05 A2 0.8 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 e 1 0.65 BSC K 0° L 0.45 0.60 0.0256 BSC 8° 0° 0.75 0.018 DocID001882 Rev 3 8° 0.024 0.030 11/13 13 Revision history 5 M74HC04 Revision history Table 12. Document revision history Date 11-Sep-2013 12/13 Revision 3 Changes Added ESD information to Features Added automotive grade order codes, temperature ranges, and marking information to Table 1: Device summary Revised document presentation Minor textual updates DocID001882 Rev 3 M74HC04 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com DocID001882 Rev 3 13/13 13