M74HC175_01

M74HC175 QUAD D-TYPE FLIP FLOP WITH CLEAR s s s s s s s HIGH SPEED : tPD = 16 ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC =4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 175 DIP SOP TSSOP ORDER CODES PACKAGE DIP SOP TSSOP TUBE M74HC175B1R M74HC175M1R T&R M74HC175RM13TR M74HC175TTR DESCRIPTION The M74HC175 is an high speed CMOS HEX D-TYPE FLIP FLOP WITH CLEAR fabricated with silicon gate C2MOS technology. These four flip-flops are controlled by a clock input (CLOCK) and a clear input (CLEAR). The information data applied to the D inputs (1D to 4D) are transferred to the outputs (1Q to 4Q and 1Q to 4Q) on the positive-going edge of the clock pulse. The reset function is accomplished when the CLEAR input is low and all Q outputs are low regardless of other input conditions. All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS July 2001 1/11 M74HC175 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No 1 2, 7, 10, 15 3, 6, 11, 14 4, 5, 12, 13 9 8 16 SYMBOL CLEAR 1Q to 4Q 1Q to 4Q 1D to 4D CLOCK GND Vcc NAME AND FUNCTION Asynchronous Master Reset (Active Low) Flip-Flop Outputs Complementary Flip-Flop Outputs Data Inputs Clock Input (LOW to HIGH, edge triggered) Ground (0V) Positive Supply Voltage TRUTH TABLE INPUTS CLEAR L H H H X : Don’t Care OUTPUTS FUNCTION CLOCK X Q L L H Qn Q H H L Qn NO CHANGE D X L H X LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays 2/11 M74HC175 ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO PD Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Power Dissipation Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 25 ± 50 500(*) -65 to +150 300 Unit V V V mA mA mA mA mW °C °C ICC or IGND DC VCC or Ground Current Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top tr, tf Supply Voltage Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time VCC = 2.0V VCC = 4.5V VCC = 6.0V Parameter Value 2 to 6 0 to VCC 0 to VCC -55 to 125 0 to 1000 0 to 500 0 to 400 Unit V V V °C ns ns ns 3/11 M74HC175 DC SPECIFICATIONS Test Condition Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 VOL Low Level Output Voltage 2.0 4.5 6.0 4.5 6.0 II ICC Input Leakage Current Quiescent Supply Current 6.0 6.0 IO=-20 µA IO=-20 µA IO=-20 µA IO=-4.0 mA IO=-5.2 mA IO=20 µA IO=20 µA IO=20 µA IO=4.0 mA IO=5.2 mA VI = VCC or GND VI = VCC or GND TA = 25°C Min. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.18 5.68 2.0 4.5 6.0 4.31 5.8 0.0 0.0 0.0 0.17 0.18 0.1 0.1 0.1 0.26 0.26 ± 0.1 4 1.9 4.4 5.9 4.13 5.63 0.1 0.1 0.1 0.33 0.33 ±1 40 Typ. Max. Value -40 to 85°C Min. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.10 5.60 0.1 0.1 0.1 0.40 0.40 ±1 80 µA µA V V Max. -55 to 125°C Min. 1.5 3.15 4.2 0.5 1.35 1.8 Max. V Unit VIH High Level Input Voltage Low Level Input Voltage High Level Output Voltage VIL V VOH 4/11 M74HC175 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 TA = 25°C Min. Typ. 30 8 7 60 19 16 50 16 14 13 52 61 28 7 6 28 7 6 28 7 6 Max. 75 15 13 150 30 26 125 25 21 5 25 30 75 15 13 75 15 13 75 15 13 0 0 0 5 5 5 95 19 16 95 19 16 95 19 16 0 0 0 5 5 5 Value -40 to 85°C Min. Max. 95 19 16 190 38 32 155 31 26 4.2 21 25 110 22 19 110 22 19 110 22 19 0 0 0 5 5 5 -55 to 125°C Min. Max. 110 22 19 225 45 38 190 38 32 ns Unit tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (CLOCK - Q, Q) tPLH tPHL Propagation Delay Time (CLEAR - Q, Q) fMAX Maximum Clock Frequency Minimum Pulse Width (CLOCK) Minimum Pulse Width (CLEAR) Minimum Set-up Time Minimum Hold Time Minimum Removal Time (CLEAR) ns ns 6.2 31 37 MHz tW(H) tW(L) tW(L) ns ns ts ns th ns tREM ns CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) 5.0 5.0 TA = 25°C Min. Typ. 5 47 Max. 10 Value -40 to 85°C Min. Max. 10 -55 to 125°C Min. Max. 10 pF pF Unit CIN CPD Input Capacitance Power Dissipation Capacitance (note 1) 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + I CC/4 (per FLIP/ FLOP) 5/11 M74HC175 TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1: PROPAGATION DELAY TIMES, MINIMUM PULSE WIDTH (CLOCK), SETUP AND HOLD TIME (D TO CLOCK) (f=1MHz; 50% duty cycle) 6/11 M74HC175 WAVEFORM 2 :MINIMUM PULSE WIDTH (CLEAR) AND REMOVAL TIME ( CLEAR TO CLOCK) (f=1MHz; 50% duty cycle) W AVEFORM 3 : INPUT WAVEFORMS (f=1MHz; 50% duty cycle) 7/11 M74HC175 Plastic DIP-16 (0.25) MECHANICAL DATA mm. DIM. MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.27 8.5 2.54 17.78 7.1 5.1 0.130 0.050 0.51 0.77 0.5 0.25 20 0.335 0.100 0.700 0.280 0.201 1.65 TYP MAX. MIN. 0.020 0.030 0.020 0.010 0.787 0.065 TYP. MAX. inch P001C 8/11 M74HC175 SO-16 MECHANICAL DATA DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 8° (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45° (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010 PO13H 9/11 M74HC175 TSSOP16 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0° 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8° 0.75 0° 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8° 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0089 0.201 0.260 0.176 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 10/11 M74HC175 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 11/11