TL074IYDT

TL074 Low-noise JFET quad operational amplifier Datasheet - production data Related products • See TL071 for single version • See TL072 for dual version Description D SO14 (plastic micropackage) Output 1 1 Inverting Input 1 2 Non-inverting Input 1 3 14 Output 4 - - 13 Inverting Input 4 + + 12 Non-inverting Input 4 11 VCC - V CC + 4 Non-inverting Input 2 Inverting Input 2 5 + + 10 Non-inverting Input 3 6 - - 9 Inverting Input 3 8 Output 3 Output 2 7 The TL074, TL074A, and TL074B are high-speed JFET input single operational amplifiers. Each of these JFET input operational amplifiers incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset currents, and low offset voltage temperature coefficient. Pin connections (top view) Features • Wide common-mode (up to VCC+) and differential voltage range • Low input bias and offset current • Low noise en = 15 nV/ √ Hz (typ) • Output short-circuit protection • High input impedance JFET input stage • Low harmonic distortion: 0.01% (typical) • Internal frequency compensation • Latch up free operation • High slew rate: 16 V/µs (typical) November 2013 This is information on a product in full production. DocID2297 Rev 5 1/18 www.st.com Contents TL074 Contents 1 Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Parameter measurement information . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Typical applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6.1 SO14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2/18 DocID2297 Rev 5 TL074 1 Schematic diagram Schematic diagram Figure 1. Circuit schematic V CC Non-inverting input Inverting input 10 0Ω 200 Ω Output 10 0Ω 1/4 TL074 30k 8.2k 1.3k 35k 1.3k 35k 10 0Ω V CC DocID2297 Rev 5 3/18 18 Absolute maximum ratings and operating conditions 2 TL074 Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings Value Symbol Parameter Unit TL074I, AI, BI VCC Supply voltage (1) ±18 (2) Vi Input voltage Vid Differential input voltage(3) Ptot Power dissipation Rthja Rthjc TL074C, AC, BC V ±15 ±30 680 Thermal resistance junction to SO14 ambient(4)(5) Thermal resistance junction to SO14 case(4)(5) Output short-circuit duration mW 105 °C/W 31 (6) Infinite Toper Operating free-air temperature range Tstg Storage temperature range -65 to +150 HBM: human body model(7) 1 kV 200 V 1.5 kV ESD MM: machine -40 to +125 0 to +70 model(8) (9) CDM: charged device model °C 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC+ and VCC-. 2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 4. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuits on all amplifiers. 5. Rth are typical values. 6. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. 7. Human body model: 100pF discharged through a 1.5kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 8. Machine model: a 200pF cap is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5Ω), done for all couples of pin combinations with other pins floating. 9. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground. Table 2. Operating conditions Symbol 4/18 Parameter TL074I, AI, BI VCC Supply voltage Toper Operating free-air temperature range TL074C, AC, BC 6 to 36 DocID2297 Rev 5 -40 to +125 Unit V 0 to +70 °C TL074 3 Electrical characteristics Electrical characteristics Table 3. VCC = ±15 V, Tamb = +25 °C (unless otherwise specified) TL074I,AC,AI, BC,BI Symbol Unit Min. Vio TL074C Parameter Typ. Max. 3 3 1 10 6 3 13 7 5 Input offset voltage (Rs = 50Ω) Tamb = +25°C TL074 TL074A TL074B Tmin ≤ Tamb ≤ TmaxTL074 TL074A TL074B Min. Typ. Max. 3 10 mV 13 Input offset voltage drift 10 Iio Input offset current Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 5 100 4 5 100 10 pA nA Iib Input bias current -note (1) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 20 200 20 30 200 20 pA nA Avd Large signal voltage gain RL= 2kΩ, Vo=±10V Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 50 25 200 25 15 200 SVR Supply voltage rejection ratio (RS = 50Ω) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 80 80 86 70 70 86 DVio ICC Supply current, no load Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Vicm Input common mode voltage range CMR Ios ±Vopp SR 1.4 10 2.5 2.5 1.4 µV/°C V/mV dB 2.5 2.5 mA ±11 +15 -12 ±11 +15 -12 V Common mode rejection ratio (RS = 50Ω) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 80 80 86 70 70 86 dB Output short-circuit current Tamb = +25°C Tmin ≤ Tamb ≤ Tmax 10 10 40 10 10 40 Output voltage swing Tamb = +25°C RL = 2kΩ RL = 10kΩ Tmin ≤ Tamb ≤ Tmax RL = 2kΩ RL = 10kΩ 10 12 10 12 12 13.5 10 12 10 12 12 13.5 V 8 13 8 13 V/µs Slew rate Vin = 10V, RL = 2kΩ, CL = 100pF, unity gain DocID2297 Rev 5 60 60 60 60 mA 5/18 18 Electrical characteristics TL074 Table 3. VCC = ±15 V, Tamb = +25 °C (unless otherwise specified) (continued) TL074I,AC,AI, BC,BI Symbol TL074C Parameter Unit Min. Typ. Max. Min. Typ. Max. tr Rise time Vin = 20mV, RL = 2kΩ, CL = 100pF, unity gain 0.1 0.1 µs Kov Overshoot Vin = 20mV, RL = 2kΩ, CL = 100pF, unity gain 10 10 % GBP Gain bandwidth product Vin= 10mV, RL= 2kΩ, CL = 100pF, = 100kHz 3 MHz Ri THD en ∅m Vo1/Vo2 2 3 2 Input resistance 1012 1012 Ω Total harmonic distortion f= 1kHz, RL = 2kΩ,CL = 100pF, Av = 20dB, Vo = 2Vpp) 0.01 0.01 % Equivalent input noise voltage RS = 100Ω, f = 1kHz 15 15 nV -----------Hz Phase margin 45 45 degrees Channel separation Av = 100 120 120 dB 1. The input bias currents are junction leakage currents which approximately double for every 10° C increase in the junction temperature. 6/18 DocID2297 Rev 5 TL074 Electrical characteristics Figure 2. Maximum peak-to-peak output voltage Figure 3. Maximum peak-to-peak output voltage versus frequency versus frequency Figure 4. Maximum peak-to-peak output voltage Figure 5. Maximum peak-to-peak output voltage versus frequency versus free air temperature MAXIMUM PE AK-T O -PE AK OUTPUT VOLT AG E (V) Figure 6. Maximum peak-to-peak output voltage Figure 7. Maximum peak-to-peak output voltage versus load resistance versus supply voltage DocID2297 Rev 5 30 25 R L = 10 kΩ Tamb = +25˚C 20 15 10 5 0 2 6 8 10 4 12 SUPPLY VOLTAGE ( V ) 14 16 7/18 18 Electrical characteristics TL074 Figure 8. Input bias current versus free air temperature Figure 9. Large signal differential voltage amplification versus free air temperature 25 1000 R L = 10 kΩ Tamb = +25˚C DIFFERENTIAL VOLTAGE AMPLIFICATION (V/mV) MAXIMUM P E AK-T O -P E AK OUT P U T VOLT AG E (V) 30 20 15 10 5 0 2 6 4 8 10 12 SUPPLY VOLTAGE ( V ) 14 400 200 100 40 20 10 1 16 V CC = 15V V O = 10V 4 2 R L = 2k Ω -75 -50 -25 0 25 50 75 100 125 TEMPERATURE (˚C) Figure 11. Total power dissipation versus free air temperature TOTAL P OW E R DIS S IP AT ION (mW ) (V/mV) Figure 10. Large signal differential voltage amplification and phase shift versus frequency 250 225 200 175 150 125 100 75 50 25 0 V C C = 15V No signal No load -75 -50 -25 0 25 50 75 100 125 TEMPERATURE (˚C ) 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 89 V C C = 15V No signal No load -75 -50 -25 0 25 50 75 100 125 C OMMON MODE MODE R E JE C T ION R ATIO (dB) S UP PL Y C UR R E NT (mA) Figure 12. Supply current per amplifier versus Figure 13. Common mode rejection ratio versus free air temperature free air temperature R L = 1 0 kΩ V C C = 1 5V 87 86 85 84 83 -75 -50 -25 0 25 50 TEMPERATURE (˚C ) TEMPERATURE (˚C ) 8/18 88 DocID2297 Rev 5 75 100 125 TL074 Electrical characteristics Figure 14. Voltage follower large signal pulse response Figure 15. Output voltage versus elapsed time 28 OUT P UT VOLT AGE (mV) 24 OVERSHOOT 20 90% 16 12 8 V C C = 15V 4 R L = 2k Ω Tamb = +25˚C 10% 0 tr -4 0 0.1 0.2 0.3 0.5 0.4 0.6 0.7 TIME ( μs ) Figure 16. Equivalent input noise voltage versus frequency Figure 17. Total harmonic distortion versus frequency 1 V C C = 15V A V = 10 R S = 100 Ω T amb = +25˚C E QUIVALE NT INP UT NOIS E VOLT AG E (nV/VHz) 60 50 40 30 20 10 0 10 40 100 400 1k 4k 10k T OTAL HAR MONIC DIS TOR T ION (%) 70 40k 100k FREQUENCY (Hz) V VC C = = 15V 15V C A AV V= =1 1 V VO O(rms) = =6V6V (rms) 0.4 0.1 0.04 CC T amb +25˚ T amb= =+25˚ 0.01 0.004 0.001 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) DocID2297 Rev 5 9/18 18 Parameter measurement information 4 TL074 Parameter measurement information Figure 18. Voltage follower Figure 19. Gain-of-10 inverting amplifier 10k Ω 1k Ω eI - 1/4 T L074 eo RL 10/18 DocID2297 Rev 5 C L = 100pF TL074 5 Typical applications Typical applications Figure 20. Audio distribution amplifier fO = 1 00 kH z 1M Ω 1 /4 T L 0 74 Output A 1 /4 T L074 Output B 1 /4 T L 0 74 Output C 1 /4 T L 0 74 1 μF - Input 100k Ω 100k Ω 100k Ω 1OO μF V C C+ - 100k Ω Figure 21. Positive feeback bandpass filter 16k Ω 16k Ω 2 2 0 pF 2 2 0 pF 43k Ω Input 43k Ω 43 k Ω 2 2 0 pF 1/4 T L 074 43k Ω 30k Ω - 2 2 0 pF 43 k Ω 1/4 T L 074 1 .5 k Ω 1 .5 k Ω 30k Ω 1/4 T L 074 43k Ω 1/4 T L 074 Output B Ground Output A DocID2297 Rev 5 11/18 18 Typical applications TL074 Figure 22. Output A Figure 23. Output B SECOND ORDER BANDPASS FILTER fo = 100 kHz; Q = 30; Gain = 16 12/18 CASCADED BANDPASS FILTER fo = 100 kHz; Q = 69; Gain = 16 DocID2297 Rev 5 TL074 6 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. DocID2297 Rev 5 13/18 18 Package information 6.1 TL074 SO14 package information Figure 24. SO14 package mechanical drawing 0016019_E 14/18 DocID2297 Rev 5 TL074 Package information Table 4. SO14 package mechanical data Dimensions Millimeters Inches Ref. Min. Typ. Max. Min. Typ. Max. A 1.35 1.75 0.05 0.068 A1 0.10 0.25 0.004 0.009 A2 1.10 1.65 0.04 0.06 B 0.33 0.51 0.01 0.02 C 0.19 0.25 0.007 0.009 D 8.55 8.75 0.33 0.34 E 3.80 4.0 0.15 0.15 e 1.27 0.05 H 5.80 6.20 0.22 0.24 h 0.25 0.50 0.009 0.02 L 0.40 1.27 0.015 0.05 k 0° 8° 0° 8° e ddd 0.40 0.015 0.10 DocID2297 Rev 5 0.004 15/18 18 Ordering information 7 TL074 Ordering information Table 5. Order codes Order code TL074IDT TL074AIDT TL074BIDT TL074IYDT(1) TL074AIYDT(1) TL074BIYDT(1) TL074CDT TL074ACDT TL074BCDT Temperature range Package Packing Marking 074I 074AI 074BI -40°C, +125°C SO14 0°C, +70°C Tape and reel 074IY 074AIY 074BIY 074C 074AC 074BC 1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent. 16/18 DocID2297 Rev 5 TL074 8 Revision history Revision history Table 6. Document revision history Date Revision 28-Mar-2001 1 Initial release. 30-Jul-2007 2 Added values for Rthja, Rthjc and ESD in Table 1: Absolute maximum ratings. Added Table 2: Operating conditions. Expanded Table 5: Order codes. Format update. 07-Jul-2008 3 Removed information concerning military temperature ranges (TL074Mx, TL074AMx, TL074BMx). Added automotive grade order codes in Table 5: Order codes. 04-Jul-2012 4 Removed commercial types TL074IYD, TL074AIYD, TL074BIYD. Updated Table 5: Order codes. 5 Added Related products on first page Removed DIP package mechanical information Table 5: Order codes: – removed commercial types related to DIP package: TL074IN, TL074AIN, TL074BIN, TL074CN, TL074ACN, TL074BCN; – removed commercial types related to tube packing: TL074ID, TL074AID, TL074BID, TL074CD, TL074ACD, TL074BCD; – changed operating temperature range for TL074IDT, TL074AIDT, TL074BIDT, TL074IYDT, TL074AIYDT, TL074BIYDT from -40 °C, +105 °C to -40 °C, +125 °C; – updated footnote for automotive parts. 22-Nov-2013 Changes DocID2297 Rev 5 17/18 18 TL074 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 18/18 DocID2297 Rev 5