TSM100ID

TSM100 SINGLE OPERATIONAL AMPLIFIER AND SINGLE COMPARATOR OPERATIONAL AMPLIFIER s LOW INPUT OFFSET VOLTAGE : 0.5mV typ. s MEDIUM BANDWIDTH (unity gain) : 0.9MHz s LARGE OUTPUT VOLTAGE SWING : 0V to (VCC - 1.5V) s INPUT COMMON MODE VOLTAGE RANGE INCLUDES GROUND s WIDE POWER SUPPLY RANGE : 5 to 30V ±2.5 TO ±15V s ESD PROTECTION : 2kV COMPARATOR (OPEN COLLECTOR) D SO8 (Plastic Micropackage) s INPUT COMMON MODE VOLTAGE RANGE INCLUDES GROUND s LOW OUTPUT SATURATION VOLTAGE : 250mV @ Io = 4mA PIN CONNECTIONS (top view) DESCRIPTION The TSM100 is a monolithic IC that includes one independent op-amp and one independent comparator. This device is offering space and cost saving in many applications like power supply management or data acquisition systems. ORDER CODE Part Number TSM100I Temperature Range -40°C, +105°C Package D • Ground : 4 Amp Output : 1 Amp Input - : 2 8 : Vcc 7 : Comp Output Amp Input + : 3 + 6 : Comp Input - 5 : Comp Input + D = Small Outline Package (SO) - also available in Tape & Reel (DT) July 2001 + 1/5 TSM100 ABSOLUTE MAXIMUM RATINGS Symbol VCC Vid Vi Toper Tj Tl Rthja Supply Voltage Differential Input Voltage Input Voltage Operating Free-air Temperature Range Maximum Junction Temperature Maximum Lead Temperature (10 seconds maximum) Thermal Resistance Junction to Ambient Parameter Value 32 32 -03. to +32 -40 to +105 150 260 175 Unit V V V °C °C °C °C/W ELECTRICAL CHARACTERISTICS Symbol ICC Parameter Total Supply Current Vcc+ = 5V, no load Vcc+ = 30V, no load Min. Typ. 0.9 Max. 1.4 1.8 Unit mA 2/5 TSM100 OPERATIONAL AMPLIFIER VCC+ = +5V, VCC = Ground, V o = 1.4V,T amb = 25°C (unless otherwise specified) Symbol Vio Parameter Input Offset Voltage Tamb = 25°C Tmin. ≤ Tamb ≤ Tmax. Input Offset Voltage Drift Input Offset Current Input Bias Current Large Signal Voltage Gain VCC = 15V, RL = 2k, Vo = 1.4V to 11.4V Supply Voltage Rejection Ratio VCC = 5V to 30V Input Common Mode Voltage Range VCC = +30V - see note 1) 50 65 0 Min. Typ. 0.5 7 2 20 100 dB 100 (VCC+) -1.5 30 150 Max. 3 4 µV/°C nA nA V/mV Unit mV DVio Iio Iib Avd SVR Vicm V dB mA CMR Isource Io Isink Common Mode Rejection Ratio Output Current Source VCC = +15V, Vo = 2V, Vid = +1V Short Circuit to Ground VCC = +15V Output Current Sink Vid = -1V, VCC = +15V, Vo = 2V VCC = +15V, Vo = 0.2V High Level Output Voltage VCC+ = 30V Tamb = 25°C, RL = 2k Tamb = 25°C, RL = 10k Low Level Output Voltage RL = 10k Slew Rate at Unity Gain Vi = 0.5 to 3V, VCC = 15V RL = 2k, CL = 100pF, unity gain Gain Bandwidth Product VCC = 30V,RL = 2k, CL = 100pF f = 100kHz, Vin = 10mV Total Harmonic Distortion f = 1kHz AV = 20dB,RL = 2k, VCC = 30V CL = 100pF, Vo = 2Vpp Equivalent Input Noise Voltage f = 1kHz, Rs = 100Ω Vcc = 30V 65 20 85 40 mA 40 60 10 12 20 50 mA µA V VOH 26 27 27 28 mV 5 15 V/µs VOL SR 0.2 0.4 MHz GBP 0.5 0.9 % 0.015 THD en nV/√Hz 40 1. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC+ - 1.5V. But both inputs can go to Vcc+ +0.3V without damage. 3/5 TSM100 COMPARATOR VCC+ = +5V, VCC = Ground,Tamb = 25°C (unless otherwise specified) Symbol Vio Iio Iib Avd Vicm Input Offset Voltage Tamb = 25°C Input Offset Current Input Bias Current Large Signal Voltage Gain VCC = 15V, RL = 15k, Vo = 1V to 11V Input Common Mode Voltage Range 1) Output Sink Current Vid = -1V, Vo = 1.5V Low Level Output Voltage Vid = -1V, Isink = 4mA High Level Output Current Vid = 1V, Vcc = Vo = 30V Response Time RL = 5.1k to VCC+ 2) Large Signal Response Time Vi = TTL, Vref = +1.4V, RL = 5.1k to VCC+ 0 6 16 Parameter Min. Typ. 1 5 25 200 (VCC+) -1.5 Max. 5 50 250 Unit mV nA nA V/mV V mA mV Isink VOL IOH tre trel 250 0.1 400 nA µs 1.3 ns 300 1. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is VCC+ - 1.5V. But either of both inputs can go to 36V without damage. 2. The response time is specified for a 100mV input step with 5mV overdrive. For larger overdrive signals, 300ns can be obtained 4/5 TSM100 PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) Millimeters Dim. Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S 0.1 0.65 0.35 0.19 0.25 4.8 5.8 1.27 3.81 3.8 0.4 4.0 1.27 0.6 8° (max.) 0.150 0.016 Typ. Max. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 45° (typ.) 5.0 6.2 0.189 0.228 Min. 0.004 0.026 0.014 0.007 0.010 Inches Typ. Max. 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.197 0.244 0.050 0.150 0.157 0.050 0.024 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 5/5