TSM1011IST

TSM1011 Constant voltage and constant current controller for battery chargers and adapters Datasheet - production data Description The TSM1011 is a highly integrated solution for SMPS applications requiring CV (constant voltage) and CC (constant current) modes. % 40 QMBTUJD
QBDLBHF The TSM1011 device integrates one voltage reference and two operational amplifiers (with ORed outputs - common collectors). Features  Constant voltage and constant current control  Low voltage operation  Low external component count  Current sink output stage The voltage reference combined with one operational amplifier makes it an ideal voltage controller. The other operational amplifier, combined with few external resistors and the voltage reference, can be used as a current limiter. Figure 1. Pin connections (top view)  Easy compensation  2 kV ESD protection  Voltage reference: – Fixed output voltage reference 2.545 V – 0.5% and 1% voltage precision  7SFG 7$$   $D
065   $D (/%  $W Applications $7
 Adapters ".7  Battery chargers Table 1. Order codes Part number Temperature range TSM1011ID TSM1011AID -0 to 105 °C Package D(1) Marking • M1011 • M1011A 1. D = “Small Outline” package (SO) - also available in tape and reel (DT). April 2016 This is information on a product in full production. DocID9310 Rev 2 1/14 www.st.com Contents TSM1011 Contents 1 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5 Internal schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6 Voltage and current control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6.1 Voltage control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 6.2 Current control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 7 Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 8 Start-up and short-circuit conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9 Voltage clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 10 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 10.1 11 2/14 SO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 DocID9310 Rev 2 TSM1011 1 Pin description Pin description Table 2 gives the pin descriptions for the SO-8 package. Table 2. SO-8 pinout 2 Name Pin no. Type Function VRef 1 Analog output Voltage reference CC- 2 Analog input Input pin of the operational amplifier CC+ 3 Analog input Input pin of the operational amplifier CV- 4 Analog input Input pin of the operational amplifier CV+ 5 Analog input Input pin of the operational amplifier GND 6 Power supply Ground line. 0 V reference for all voltages. OUT 7 Analog output Output of the two operational amplifiers VCC 8 Power supply Power supply line Absolute maximum ratings Table 3. Absolute maximum ratings Symbol Value Unit DC supply voltage (50 mA =< ICC) -0.3 V to Vz V Vi Input voltage -0.3 to VCC V PT Power dissipation Tstg Storage temperature -55 to 150 °C Tj Junction temperature 150 °C Voltage reference output current 10 mA ESD Electrostatic discharge 2 KV Rthja Thermal resistance junction to ambient SO-8 package 175 °C/W Value Unit VCC Iref 3 DC supply voltage W Operating conditions Table 4. Operating conditions Symbol Parameter VCC DC supply conditions 4.5 to Vz V Toper Operational temperature 0 to 105 °C DocID9310 Rev 2 3/14 14 Electrical characteristics 4 TSM1011 Electrical characteristics Tamb = 25 °C and VCC = +18 V (unless otherwise specified). Table 5. Electrical characteristics Symbol Parameter Test condition Min. Typ. Max. Unit 1 mA Total current consumption ICC Total supply current, excluding current in voltage reference VCC = 18 V, no load Tmin. < Tamb < Tmax. Vz VCC clamp voltage ICC = 50 mA 28 Input offset voltage TSM1011 Tamb = 25 °C Tmin.  Tamb  Tmax. Tamb = 25 °C Tmin.  Tamb Tmax. 1 V Operators Vio TSM1011A DVio 0.5 Input offset voltage drift 4 5 2 3 mV V/°C 7 Iio Input offset current Tamb = 25 °C Tmin.  Tamb  Tmax. 2 30 50 nA Iib Input bias current Tamb = 25 °C Tmin.  Tamb  Tmax. 20 50 150 200 nA SVR Supply voltage rejection ration VCC = 4.5 V to 28 V Vicm Input common mode voltage range for CV op-amp 1.5 VCC -1.5 V Vicm Input common mode voltage range for CC op-amp 0 VCC -1.5 V CMR Common mode rejection ratio 65 100 Tamb = 25 °C Tmin.  Tamb  Tmax. 70 60 85 Tamb = 25 °C Tmin.  Tamb  Tmax. 1 3.5 2.5 dB dB Output stage Gm Transconduction gain. Sink current only(1) Vol Low output voltage at 10 mA sinking current Ios Output short-circuit current. Output to VCC . Sink current only. 4/14 Tamb = 25 °C Tmin.  Tamb  Tmax. DocID9310 Rev 2 mA/mV 200 600 mV 27 50 mA TSM1011 Electrical characteristics Table 5. Electrical characteristics (continued) Symbol Parameter Test condition Min. Typ. Max. Unit 2.519 2.545 2.532 2.545 2.57 2.557 V 30 mV Voltage reference VRef VRef Reference input voltage, Iload = 1 mA TSM1011 1% precision TSM1011A 0.5% precision Tamb = 25 °C Reference input voltage deviation over the Tmin.  Tamb  Tmax. temperature range 20 RegLine Reference input voltage deviation over the Iload = 5 mA VCC range 20 mV RegLoad Reference input voltage deviation over the VCC = 18 V, output current 0 < Iload < 10 mA 10 mV 1. The current depends on the voltage difference between the negative and the positive inputs of the amplifier. If the voltage on the minus input is 1 mV higher than the positive amplifier, the sinking current at the output OUT will be increased by 3.5 mA. DocID9310 Rev 2 5/14 14 Internal schematic 5 TSM1011 Internal schematic Figure 2. Internal schematic   7SFG 7$$ 
7 $W  $7 $D  $$ $D $W  0VU  (/%   ". Figure 3. Typical adapter application using TSM1011  3 7SFG 7$$ 3 5P
QSJNBSZ
 
7  54. $W 3 $W $D 0VU   3WD  (/%  3 7TFOTF   $D $$  *- -PBE $7  065 % 3JD $JD 
O' $WD 
O' 3 3JD 065 3TFOTF *- ". In the application schematic shown in Figure 3, the TSM1011 is used on the secondary side of a flyback adapter (or battery charger) to provide accurate control of the voltage and current. The above feedback loop is made with an optocoupler. 6/14 DocID9310 Rev 2 TSM1011 Voltage and current control 6 Voltage and current control 6.1 Voltage control The voltage loop is controlled via a first transconductance operational amplifier, the resistor bridge R1, R2, and the optocoupler which is directly connected to the output. The relative values of R1 and R2 should be chosen in accordance with Equation 1: Equation 1 R1 = R2 x VRef / (Vout - VRef) where Vout is the desired output voltage. To avoid the discharge of the load, the resistor bridge R1, R2 should have high impedance. For this type of application, a total value of 100 K (or more) would be appropriate for the resistors R1 and R2. For example, with R2 = 100 K, Vout = 4.10 V, VRef = 2.5 V, then R1 = 41.9 K. Note: If the low drop diode is to be inserted between the load and the voltage regulation resistor bridge to avoid current flowing from the load through the resistor bridge, this drop should be taken into account in Equation 1 by replacing Vout by (Vout + Vdrop). 6.2 Current control The current loop is controlled via the second transconductance operational amplifier, the sense resistor Rsense, and the optocoupler. Vsense threshold is achieved externally by a resistor bridge tied to the VRef voltage reference. Its midpoint is tied to the positive input of the current control operational amplifier, and its foot is to be connected to the lower potential point of the sense resistor, as shown in Figure 4. The resistors of this bridge are matched to provide the best precision possible. The control equation verifies that: Equation 2 R sense  I lim = V sense R 5  V ref V sense = ------------------------ R4 + R5  Equation 3 R 5  V ref I lim = ----------------------------------------------- R 4 + R 5   R sense where Ilim is the desired limited current, and Vsense is the threshold voltage for the current control loop. Note that the Rsense resistor should be chosen taking into account the maximum dissipation (Plim) through it during the full load operation. DocID9310 Rev 2 7/14 14 Voltage and current control TSM1011 Equation 4 P lim = V sense  I lim Therefore, for most adapter and battery charger applications, a quarter-watt, or half-watt resistor to make the current sensing function is sufficient. The current sinking outputs of the two transconductance operational amplifiers are common (to the output of the IC). This makes an ORing function which ensures that whenever the current or the voltage reaches too high values, the optocoupler is activated. The relation between the controlled current and the controlled output voltage can be described with a square characteristic as shown in the following V/I output power graph. Figure 4. Output voltage versus output current 7PMUBHF
SFHVMBUJPO $VSSFOU
SFHVMBUJPO 7PVU  54.
7$$

JOEFQFOEFOU
QPXFS
TVQQMZ 4FDPOEBSZ
DVSSFOU
SFHVMBUJPO *PVU 54.
7$$ 
PO QPXFS
PVUQVU
1SJNBSZ
DVSSFOU
SFHVMBUJPO ".W 8/14 DocID9310 Rev 2 TSM1011 Compensation The voltage control transconductance operational amplifier can be fully compensated. Both its output and negative input are directly accessible for external compensation components. An example of a suitable voltage control compensation network is shown in Figure 6. It consists of a capacitor Cvc1 = 2.2 nF and a resistor Rcv1 = 22 K in series. The current control transconductance operational amplifier can be fully compensated. Both of its output and negative input are directly accessible for external compensation components. An example of a suitable current control compensation network is also shown in Figure 6. It consists of a capacitor Cic1 = 2.2 nF and a resistor Ric1 = 22 K in series. Figure 5. Schematic of compensation network 7$$ 3MJNJU  7SFG  5P
QSJNBSZ
7$$ 
7 %4  3 *- 3 54. $W 065 % $7 3   $W   $D 0VU (/%   3 7TFOTF   $D $$ $4 -PBE 7 Compensation 3JD  3WD $JD 
O' $WD 
O' 3 3JD 3TFOTF *- 065 ". DocID9310 Rev 2 9/14 14 Start-up and short-circuit conditions 8 TSM1011 Start-up and short-circuit conditions Under start-up or short-circuit conditions the TSM1011 is not provided with a high enough supply voltage. This is due to the fact that the chip has its power supply line in common with the power supply line of the system. Therefore, the current limitation can only be ensured by the primary PWM module, which should be chosen accordingly. If the primary current limitation is not considered to be precise enough for the application, then a sufficient supply for the TSM1011 has to be ensured under all conditions. This means that it is necessary to add some circuitry to supply the chip with a separate power line. This can be achieved in numerous ways, including an additional winding on the transformer. 9 Voltage clamp The schematic in Figure 10 shows how to realize a low-cost power supply for the TSM1011 (with no additional windings). Please pay attention to the fact that in the particular case presented here, this low-cost power supply can reach voltages as high as twice the voltage of the regulated line. Since the absolute maximum rating of the TSM1011 supply voltage is 28 V. In the aim to protect the TSM1011 against such high voltage values an internal Zener clamp is integrated (see Figure 6). Equation 5 R limit = I vz   VCC – V z  Figure 6. Clamp voltage 7$$ 3MJNJU *W[ 7$$ 7[ 54. 
7 ".W 10/14 DocID9310 Rev 2 TSM1011 10 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. 10.1 SO-8 package information Figure 7. SO-8 package outline DocID9310 Rev 2 11/14 14 Package information TSM1011 Table 6. SO-8 package mechanical data Dimensions (mm) Symbol Min. Typ. A Max. 1.75 A1 0.10 A2 1.25 b 0.28 0.48 c 0.17 0.23 (1) 4.80 4.90 5.00 E 5.80 6.00 6.20 E1(2) 3.80 3.90 4.00 D e 0.25 1.27 h 0.25 0.50 L 0.40 1.27 L1 k 1.04 0° ccc 8° 0.10 1. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15 mm in total (both sides). 2. Dimension “E1” does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25 mm per side. 12/14 DocID9310 Rev 2 TSM1011 11 Revision history Revision history Table 7. Document revision history Date Revision 01 -Nov-2003 1 Initial release. 2 Removed Mini SO-8 package from the whole document. Updated Section 10: Package information on page 11 (replaced Figure 7 on page 11 by new figure, updated Table 6 on page 12). Minor modifications throughout document. 15-Apr-2016 Changes DocID9310 Rev 2 13/14 14 TSM1011 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved 14/14 DocID9310 Rev 2