Notice for TAIYO YUDEN Products
[ For General Electronic Equipment ]
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2018. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully
before practical application or use of our products.
Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or
equipment incorporating our products, which are caused under the conditions other than those specified in this
catalog or individual product specification sheets.
■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification
sheets are available.
■ Please conduct validation and verification of our products in actual condition of mounting and operating
environment before using our products.
■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA
equipment, home electric appliances, office equipment, information and communication equipment including,
without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be
sure to contact TAIYO YUDEN for further information before using the products for any equipment which may
directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation,
automotive powertrain control system, train control system, and ship control system, traffic signal equipment,
disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information
network equipment including, without limitation, telephone exchange, and base station).
Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g.,
aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control
equipment, undersea equipment, military equipment).
*Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g.,
in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN.
Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment.
When our products are used even for high safety and/or reliability-required devices or circuits of general electronic
equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to
install a protection circuit as necessary.
Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way
responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog
for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above.
■ Information contained in this catalog is intended to convey examples of typical performances and/or applications
of our products and is not intended to make any warranty with respect to the intellectual property rights or any
other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights.
■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and
TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products.
Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality
assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in
accordance with such agreement.
■ The contents of this catalog are applicable to our products which are purchased from our sales offices or
authorized distributors (hereinafter“TAIYO YUDEN’
s official sales channel”). Please note that the contents of this
catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’
s official sales
channel.
■ Caution for Export
Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export
Administration Regulations”
,“Foreign Exchange and Foreign Trade Control Law”of Japan, and other applicable
regulations. Should you have any questions on this matter, please contact our sales staff.
19
WIRE-WOUND CHIP INDUCTORS (LB SERIES)
WIRE-WOUND CHIP INDUCTORS（LB SERIES）
REFLOW
REFLOW
■PARTS NUMBER
L
B
①
* Operating Temp.：-40～+105℃（Including self-generated heat）
△ △
②
2
0
1
③
①Series name
Code
LB
2
T
④
1
0 0
⑤
M △ △ △ △
⑥ ⑦
⑧
④Packaging
Code
T
Series name
Wound chip inductor
Packaging
Taping
⑤Nominal inductance
Code
（example）
1R0
100
101
※R＝Decimal point
Characteristics
Standard
High current
Low Rdc
Low loss
Nominal inductance［μH］
／ STANDARD INDUCTORS
INDUCTORS
②Characteristics
Code
△△
△C
△R
MF
△＝Blank space
1.0
10
100
③Dimensions（L×W）
Code
Type（inch）
1608
2012
2016
2518
3218
3225
1608（0603）
2012（0805）
2016（0806）
2518（1007）
3218（1207）
3225（1210）
⑥Inductance tolerance
Code
K
M
Dimensions
（L×W）［mm］
1.6×0.8
2.0×1.25
2.0×1.6
2.5×1.8
3.2×1.8
3.2×2.5
Inductance tolerance
±10％
±20％
⑦Special code
Code
△
R
Special code
Standard
Low Rdc type
⑧Internal code
■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
Recommended Land Patterns
Surface Mounting
・Mounting and soldering conditions should be checked beforehand.
・Applicable soldering process to these products is reflow soldering
W
Type
A
L
1608
0.55
T
C
MF1608
0.55
2012
0.60
e
2016
0.60
2518
0.60
A
B
A
3218
0.85
3225
0.85
Type
LB
1608
LBMF1608
LB
LB
LB
LB
LB
LB
LB
LB
2012
C2012
R2012
2016
C2016
2518
C2518
R2518
LB
3218
LB C3225
only.
B
0.7
0.7
1.0
1.0
1.5
1.7
1.7
C
0.9
1.0
1.45
1.8
2.0
2.0
2.7
Unit：mm
Standard quantity［pcs］
Paper tape
Embossed tape
L
W
T
e
1.6±0.1
（0.063±0.004）
1.6±0.2
（0.063±0.008）
0.8±0.1
（0.031±0.004）
0.8±0.2
（0.031±0.008）
0.8±0.1
（0.031±0.004）
0.8±0.2
（0.031±0.008）
0.35±0.15
（0.014±0.006）
0.45±0.15
（0.016±0.006）
2.0±0.2
（0.079±0.008）
1.25±0.2
（0.049±0.008）
1.25±0.2
（0.049±0.008）
2.0±0.2
（0.079±0.008）
1.6±0.2
（0.063±0.008）
2.5±0.2
（0.098±0.008）
3.2±0.2
（0.126±0.008）
3.2±0.2
（0.126±0.008）
4000
－
－
3000
0.5±0.2
（0.020±0.008）
－
3000
1.6±0.2
（0.063±0.008）
0.5±0.2
（0.020±0.008）
－
2000
1.8±0.2
（0.071±0.008）
1.8±0.2
（0.071±0.008）
0.5±0.2
（0.020±0.008）
－
2000
1.8±0.2
（0.071±0.008）
2.5±0.2
（0.098±0.008）
1.8±0.2
（0.071±0.008）
2.5±0.2
（0.098±0.008）
0.6±0.2
（0.024±0.008）
0.6±0.3
（0.024±0.012）
－
2000
－
1000
Unit：mm（inch）
i_wound_LB_e-E05R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
89
■PARTS NUMBER
●1608（0603）type
Parts number
LB
LB
LB
LB
LB
1608T1R0M
1608T2R2M
1608T4R7M
1608T8R2M
1608T100M
Parts number
LBMF1608T1R0M
LBMF1608T2R2M
LBMF1608T3R3M
LBMF1608T4R7M
LBMF1608T100[]
LBMF1608T220[]
LBMF1608T470[]
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal inductance
［μH］
1.0
2.2
4.7
8.2
10
Nominal inductance
［μH］
1.0
2.2
3.3
4.7
10
22
47
Inductance tolerance
±20％
±20％
±20％
±20％
±20％
Inductance tolerance
±20％
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
／ STANDARD INDUCTORS
INDUCTORS
Self-resonant frequency
［MHｚ］（min.）
100
80
45
32
32
DC Resistance
［Ω］（±30％）
0.17
0.33
0.55
0.70
0.70
Rated current
［mA］（max.）
160
115
70
60
60
Measuring frequency
［MHz］
7.96
7.96
7.96
2.52
2.52
Self-resonant frequency
［MHｚ］（min.）
100
80
60
45
32
16
11
DC Resistance
［Ω］（±30％）
0.09
0.17
0.22
0.24
0.36
1.0
2.5
Rated current
［mA］（max.）
230
160
130
110
80
50
35
Measuring frequency
［MHz］
7.96
7.96
7.96
7.96
2.52
2.52
2.52
Self-resonant frequency
［MHｚ］（min.）
100
80
55
45
38
32
32
28
16
11
10
8
DC Resistance
［Ω］（±30％）
0.15
0.23
0.30
0.40
0.47
0.70
0.50
1.3
1.7
3.7
6.0
7.0
Rated current
［mA］（max.）
405
260
235
190
135
120
120
100
80
60
50
45
Measuring frequency
［MHz］
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
0.796
Self-resonant frequency
［MHｚ］（min.）
100
70
45
40
16
11
DC Resistance
［Ω］（±30％）
0.19
0.33
0.50
1.2
3.7
5.8
Rated current
［mA］（max.）
620
430
295
200
130
90
Measuring frequency
［MHz］
7.96
7.96
7.96
2.52
2.52
2.52
Self-resonant frequency
［MHｚ］（min.）
100
80
45
32
16
11
8
DC Resistance
［Ω］（±30％）
0.07
0.13
0.24
0.36
1.0
1.7
4.0
Rated current
［mA］（max.）
400
260
200
150
100
75
50
Measuring frequency
［MHz］
7.96
7.96
7.96
2.52
2.52
2.52
0.796
Self-resonant frequency
［MHｚ］（min.）
100
80
70
55
45
38
32
28
16
14
11
10
8
DC Resistance
［Ω］（±30％）
0.09
0.11
0.13
0.20
0.25
0.35
0.50
0.70
1.0
1.7
2.4
3.0
4.5
Rated current
［mA］（max.）
490
380
375
285
225
200
155
130
105
85
70
55
40
Measuring frequency
［MHz］
7.96
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
0.796
●2012（0805）type
Parts number
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
2012T1R0M
2012T2R2M
2012T3R3M
2012T4R7M
2012T6R8M
2012T100[]
2012T100[]R
2012T150[]
2012T220[]
2012T470[]
2012T680[]
2012T101[]
Parts number
LB
LB
LB
LB
LB
LB
C2012T1R0M
C2012T2R2M
C2012T4R7M
C2012T100[]
C2012T220[]
C2012T470[]
Parts number
LB
LB
LB
LB
LB
LB
LB
R2012T1R0M
R2012T2R2M
R2012T4R7M
R2012T100[]
R2012T220[]
R2012T470[]
R2012T101[]
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal inductance
［μH］
1.0
2.2
3.3
4.7
6.8
10
10
15
22
47
68
100
Nominal inductance
［μH］
1.0
2.2
4.7
10
22
47
Nominal inductance
［μH］
1.0
2.2
4.7
10
22
47
100
Inductance tolerance
±20％
±20％
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
Inductance tolerance
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
Inductance tolerance
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
●2016（0806）type
Parts number
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
・ []
EHS
2016T1R0M
RoHS
2016T1R5M
RoHS
2016T2R2M
RoHS
2016T3R3M
RoHS
2016T4R7M
RoHS
2016T6R8M
RoHS
2016T100[]
RoHS
2016T150[]
RoHS
2016T220[]
RoHS
2016T330[]
RoHS
2016T470[]
RoHS
2016T680[]
RoHS
2016T101[]
RoHS
Please specify the Inductance
Nominal inductance
［μH］
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
tolerance code（K or M）
Inductance tolerance
±20％
±20％
±20％
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
LB/LBC series
Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias.
LBR series
Rated Current : The maximum DC value having inductance decrease within 20 % and temperature increase within 20 degC by the application of DC bias.
i_wound_LB_e-E05R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
90
19
■PARTS NUMBER
Parts number
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
C2016T1R0M
C2016T1R5M
C2016T2R2M
C2016T3R3M
C2016T4R7M
C2016T6R8M
C2016T100[]
C2016T150[]
C2016T220[]
C2016T330[]
C2016T470[]
C2016T680[]
C2016T101[]
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal inductance
［μH］
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
Inductance tolerance
±20％
±20％
±20％
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
Self-resonant frequency
［MHｚ］（min.）
100
80
70
55
45
38
32
28
16
14
11
10
8
DC Resistance
［Ω］（±30％）
0.10
0.15
0.20
0.27
0.37
0.59
0.82
1.2
1.8
2.8
4.3
7.0
8.0
Rated current
［mA］（max.）
690
600
520
410
355
290
245
200
165
135
110
95
75
Measuring frequency
［MHz］
7.96
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
0.796
Self-resonant frequency
［MHｚ］（min.）
100
80
68
54
46
46
38
30
23
19
15
12
9.5
9.0
7.0
5.5
4.5
3.5
3.0
2.4
DC Resistance
［Ω］（±30％）
0.06
0.07
0.09
0.11
0.13
0.10
0.15
0.25
0.32
0.50
0.70
0.95
1.5
2.1
3.2
4.5
7.0
10
17
24
Rated current
［mA］（max.）
665
405
340
280
240
235
195
165
145
115
95
85
70
60
45
40
30
25
20
15
Measuring frequency
［MHz］
7.96
7.96
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
0.796
0.796
0.796
0.796
0.796
0.796
0.252
Self-resonant frequency
［MHｚ］（min.）
100
100
80
68
54
41
38
30
23
19
15
12
9.5
9.0
7.0
5.5
4.5
3.5
3.0
DC Resistance
［Ω］（±30％）
0.08
0.07
0.11
0.13
0.16
0.20
0.30
0.36
0.65
0.77
1.5
1.9
2.8
3.7
6.1
8.4
12.3
22
28
Rated current
［mA］（max.）
775
890
730
630
560
510
420
375
285
250
185
165
140
125
95
80
65
50
45
Measuring frequency
［MHz］
7.96
7.96
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
0.796
0.796
0.796
0.796
0.796
0.796
Self-resonant frequency
［MHｚ］（min.）
100
68
45
30
19
11
9
DC Resistance
［Ω］（±30％）
0.045
0.07
0.10
0.19
0.44
0.84
1.89
Rated current
［mA］（max.）
960
480
345
235
175
120
80
Measuring frequency
［MHz］
7.96
7.96
7.96
2.52
2.52
2.52
0.796
●2518（1007）type
Parts number
2518T1R0M
2518T1R5M
2518T2R2M
2518T3R3M
2518T4R7M
2518T4R7MR
2518T6R8M
2518T100[]
2518T150[]
2518T220[]
2518T330[]
2518T470[]
2518T680[]
2518T101[]
2518T151[]
2518T221[]
2518T331[]
2518T471[]
2518T681[]
2518T102[]
Parts number
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
C2518T1R0M
C2518T1R0MR
C2518T1R5M
C2518T2R2M
C2518T3R3M
C2518T4R7M
C2518T6R8M
C2518T100[]
C2518T150[]
C2518T220[]
C2518T330[]
C2518T470[]
C2518T680[]
C2518T101[]
C2518T151[]
C2518T221[]
C2518T331[]
C2518T471[]
C2518T681[]
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal inductance
［μH］
1.0
1.5
2.2
3.3
4.7
4.7
6.8
10
15
22
33
47
68
100
150
220
330
470
680
1000
Nominal inductance
［μH］
1.0
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
150
220
330
470
680
Nominal inductance
Parts number
EHS
［μH］
LB R2518T1R0M
RoHS
1.0
LB R2518T2R2M
RoHS
2.2
LB R2518T4R7M
RoHS
4.7
LB R2518T100[]
RoHS
10
LB R2518T220[]
RoHS
22
LB R2518T470[]
RoHS
47
LB R2518T101[]
RoHS
100
・ [] Please specify the Inductance tolerance code（K or M）
Inductance tolerance
±20％
±20％
±20％
±20％
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
Inductance tolerance
±20％
±20％
±20％
±20％
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
Inductance tolerance
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
／ STANDARD INDUCTORS
INDUCTORS
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
EHS
LB/LBC series
Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias.
LBR series
Rated Current : The maximum DC value having inductance decrease within 20 % and temperature increase within 20 degC by the application of DC bias.
i_wound_LB_e-E05R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
19
91
■PARTS NUMBER
●3218（1207）type
Parts number
／ STANDARD INDUCTORS
INDUCTORS
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
LB
3218T1R0M
3218T1R5M
3218T2R2M
3218T3R3M
3218T4R7M
3218T6R8M
3218T100[]
3218T150[]
3218T220[]
3218T330[]
3218T470[]
3218T680[]
3218T101[]
3218T151[]
3218T221[]
3218T331[]
3218T471[]
3218T681[]
3218T102[]
EHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
Nominal inductance
［μH］
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
150
220
330
470
680
1000
Inductance tolerance
±20％
±20％
±20％
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
Self-resonant frequency
［MHｚ］（min.）
100
80
68
54
41
40
30
25
19
15
12
11
8.0
7.0
5.0
4.0
3.5
3.0
2.4
DC Resistance
［Ω］（±30％）
0.06
0.07
0.09
0.11
0.13
0.17
0.25
0.32
0.49
0.75
0.92
1.49
2.4
3.2
5.4
7.0
14
17
27
Rated current
［mA］（max.）
1,075
860
775
560
550
380
340
300
255
215
205
145
140
105
80
65
54
45
39
Measuring frequency
［MHz］
7.96
7.96
7.96
7.96
7.96
7.96
2.52
2.52
2.52
2.52
2.52
2.52
0.796
0.796
0.796
0.796
0.796
0.796
0.252
Self-resonant frequency
［MHｚ］（min.）
250
220
190
160
70
50
23
20
17
13
10
8
6
DC Resistance
［Ω］（±30％）
0.055
0.060
0.080
0.095
0.100
0.120
0.133
0.195
0.27
0.41
0.67
1.0
1.4
Rated current
［mA］（max.）
1,100
1,000
930
820
680
620
540
420
330
300
220
190
150
Measuring frequency
［MHz］
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
●3225（1210）type
Parts number
EHS
LB C3225T1R0MR
RoHS
LB C3225T1R5MR
RoHS
LB C3225T2R2MR
RoHS
LB C3225T3R3MR
RoHS
LB C3225T4R7MR
RoHS
LB C3225T6R8MR
RoHS
LB C3225T100[]R
RoHS
LB C3225T150[]R
RoHS
LB C3225T220[]R
RoHS
LB C3225T330[]R
RoHS
LB C3225T470[]R
RoHS
LB C3225T680[]R
RoHS
LB C3225T101[]R
RoHS
・ [] Please specify the Inductance
Nominal inductance
［μH］
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
tolerance code（K or M）
Inductance tolerance
±20％
±20％
±20％
±20％
±20％
±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
±10％，±20％
LB/LBC series
Rated Current : The maximum DC value having inductance decrease within 10 % and temperature increase within 20 degC by the application of DC bias.
i_wound_LB_e-E05R01
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) .
92
19
WIRE-WOUND CHIP INDUCTORS (LB SERIES)，
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)，
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
■PACKAGING
①Minimum Quantity
Standard Quantity ［pcs］
Paper Tape
Embossed Tape
Type
LB C3225
CB C3225
LB 3218
LB R2518
LB C2518
LB 2518
CB 2518
CB C2518
LBM2016
LB C2016
LB 2016
CB 2016
CB C2016
LB 2012
LB C2012
LB R2012
CB 2012
CB C2012
CB L2012
LB 1608
LBMF1608
CBMF1608
－
1000
－
2000
－
2000
－
2000
－
3000
4000
4000
－
－
－
3000
②Tape material
●Embossed tape
Top tape
Chip Filled
Sprocket hole
Base tape
Chip cavity
Chip
●Card board carrier tape
Top tape
Base tape
Chip Filled
Sprocket hole
Bottom tape
Chip cavity
Chip
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_pack_e-E05R01
③Taping Dimensions
●Embossed Tape （0.315 inches wide）
A
B
F
Type
LBM2016
LB C3225
CB C3225
LB
3218
LB 2518
CB 2518
LB C2518
CB C2518
LB R2518
LB 2016
CB 2016
LB C2016
CB C2016
LB 2012
CB 2012
LB C2012
CB C2012
LB R2012
LBMF1608
CBMF1608
1.75±0.1
(0.069±0.004）
8.0±0.3
(0.315±0.012)
φ1.5＋0.1/－0
(φ0.059＋0.004/-0)
3.5±0.05
(0.138±0.002)
Sprocket hole
4.0±0.1
(0.157±0.004)
2.0±0.1
(0.079±0.004)
Chip cavity
A
B
1.75±0.1
2.1±0.1
（0.069±0.004）
（0.083±0.004）
2.8±0.1
3.5±0.1
（0.110±0.004）
（0.138±0.004）
2.1±0.1
3.5±0.1
（0.083±0.004）
（0.138±0.004）
Insertion pitch
F
4.0±0.1
（0.157±0.004）
4.0±0.1
（0.157±0.004）
4.0±0.1
（0.157±0.004）
Tape thickness
T
K
0.3±0.05
1.9max.
（0.012±0.002）
（0.075max.）
0.3±0.05
4.0max.
（0.012±0.002）
（0.157max.）
0.3±0.05
2.2max.
（0.012±0.002）
（0.087max.）
2.15±0.1
（0.085±0.004）
2.7±0.1
（0.106±0.004）
4.0±0.1
（0.157±0.004）
0.3±0.05
（0.012±0.002）
2.2max.
（0.087max.）
1.75±0.1
（0.069±0.004）
2.1±0.1
（0.083±0.004）
4.0±0.1
（0.157±0.004）
0.3±0.05
（0.012±0.002）
1.9max.
（0.075max.）
1.45±0.1
（0.057±0.004）
2.25±0.1
（0.089±0.004）
4.0±0.1
（0.157±0.004）
0.25±0.05
（0.010±0.002）
1.45max.
（0.057max.）
1.1±0.1
（0.043±0.004）
1.9±0.1
（0.075±0.004）
4.0±0.1
（0.157±0.004）
0.25±0.05
（0.010±0.002）
1.2max.
（0.047max.）
Unit：mm（inch）
Insertion pitch
F
4.0±0.1
（0.157±0.004）
4.0±0.1
（0.157±0.004）
Tape thickness
T
1.1max.
（0.043max.）
1.1max.
（0.043max.）
Unit：mm（inch）
●Card board carrier tape（0.315 inches wide）
A
B
F
Type
CB L2012
LB
1608
1.75±0.1
(0.069±0.004）
T
8.0±0.3
(0.315±0.012)
φ1.5＋0.1/－0
(φ0.059＋0.004/-0)
3.5±0.05
(0.138±0.002)
Sprocket hole
4.0±0.1
(0.157±0.004)
2.0±0.1
(0.079±0.004)
Chip cavity
A
B
1.55±0.1
2.3±0.1
（0.061±0.004）
（0.091±0.004）
1.0±0.1
1.8±0.1
（0.039±0.004）
（0.071±0.004）
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_pack_e-E05R01
④Leader and Blank Portion
⑤Reel Size
⑥Top Tape Strength
The top tape requires a peel-off force 0.2 to 0.7N in the direction of the arrow as illustrated below.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_pack_e-E05R01
WIRE-WOUND CHIP INDUCTORS (LB SERIES),
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES),
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
■RELIABILITY DATA
1.Operating temperature Range
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
－40～＋105℃（Including self-generated heat）
LBM Series
2. Storage Temperature Range（after soldering）
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
－40～＋85℃
LBM Series
Test Methods and
Remarks
LB, CB Series：
Please refer the term of "7. storage conditions" in precautions.
3.Rated Current
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
Within the specified tolerance
LBM Series
4.Inductance
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
Within the specified tolerance
LBM Series
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBMF・CBMF・LBM Series
Measuring equipment
：LCR Mater（HP4285A or its equivalent）
Measuring frequency
: Specified frequency
5.Q
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
LBM Series
Measuring equipment
Measuring frequency
－
Within the specified tolerance
: LCR Mater（HP4285A or its equivalent）
: Specified frequency
6.DC Resisitance
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
Within the specified tolerance
LBM Series
Test Methods and
Remarks
Measuring equipment : DC Ohmmeter （HIOKI 3227 or its equivalent）
7.Self-Resonant Frequency
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
Within the specified tolerance
LBM Series
Test Methods and
Remarks
Measuring equipment : Impedance analyzer （HP4291A or its equivalent）
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_reli_e-E05R01
8.Temperature Characteristic
LBM2016
Specified Value
Test Methods and
Remarks
Inductance change : Within±5％
LB1608
LB2012
LBR2012
CB2012
CBL2012
LB2016
CB2016
LB2518
LBR2518
CB2518
LBC3225
CBC3225
LBMF1608
CBMF1608
LBC2016
CBC2016
LBC2518
CBC2518
LB3218
LBC2012
CBC2012
Inductance change : Within±20％
Inductance change : Within±25％
Inductance change : Within±35％
Based on the inductance at 20℃ and Measured at the ambient of －40℃～＋85℃.
9.Rasistance to Flexure of Substrate
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
No damage.
LBM Series
Warp
: 2mm（LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF Series）
Test substrate : Glass epoxy-resin substrate
Thickness
: 0.8mm（LB1608・LBMF1608・CBMF1608）
: 1.0mm（Others）
Test Methods and
Remarks
10.Body Strength
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
No damage.
LBM Series
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBM
Applied force : 10N
Duration
: 10sec.
LB1608・LBMF1608・CBMF1608
Applied force : 5N
Duration
: 10sec.
11.Adhesion of terminal electrode
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
No abnormality.
LBM Series
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF
Applied force
: 10N to X and Y directions
Duration
: 5 sec.
Test substrate
: Printed board
LB1608・CBMF1608・LBMF1608
Applied force
: 5N to X and Y directions
Duration
: 5 sec.
Test substrate
: Printed board
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_reli_e-E05R01
12.Resistance to vibration
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
Inductance change : Within±5％
No significant abnormality in appearance.
LBM Series
Test Methods and
Remarks
Inductance change : Within±10％
No significant abnormality in appearance.
LB・LBR・LBC・CB・CBC・CBL・LBM・LBMF・CBMF：
The given sample is soldered to the board and then it is tested depending on the conditions of the following table.
Vibration Frequency
10～55Hz
Total Amplitude
1.5mm (May not exceed acceleration 196m/s2)
Sweeping Method
10Hz to 55Hz to 10Hz for 1min.
X
Time
Y
For 2 hours on each X, Y, and Z axis.
Z
Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
13.Drop test
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
－
LBM Series
14.Solderability
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
At least 90％ of surface of terminal electrode is covered by new
LBM Series
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF：
Solder temperature
: 245±5℃
Duration
: 5±0.5sec
Flux
: Methanol solution with 25％ of colophony
15.Resistance to soldering
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
Inductance change : Within±10％
Inductance change : Within±5％
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF：
3 times of reflow oven at 230℃ MIN for 40sec. with peak temperature at 260 ℃ for 5sec.
Recovery : At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
16.Resisitance to solvent
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
－
LBM Series
Test Methods and
Remarks
Solvent temperature
Type of solvent
Cleaning conditions
: Room temperature
: Isopropyl alcohol
: 90s. Immersion and cleaning.
17.Thermal shock
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
Inductance change : Within±10％
No significant abnormality in appearance.
LBM Series
Test Methods and
Remarks
LB・LBC・LBR・CB・CBC・CBL・LBM・LBMF・CBMF：
The given sample is soldered to the board and then its Inductance is measured after 100cycles of the following conditions.
Conditions of 1 cycle
Step
Temperature (℃)
Duration (min)
1
－40±3
30±3
2
Room temperature
Within 3
3
＋85±2
30±3
4
Room temperature
Within 3
Recovery
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_reli_e-E05R01
18.Damp heat life test
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
Inductance change : Within±10％
No significant abnormality in appearance.
LBM Series
Test Methods and
Remarks
Temperature
Humidity
Duration
Recovery
: 60±2℃
: 90～95％RH
: 1000 hrs
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
19.Loading under damp heat life test
LB, LBC, LBR, LBMF Series
CB, CBC, CBL, CBMF Series
Specified Value
Test Methods and
Remarks
Inductance change : Within±10％
No significant abnormality in appearance.
LBM Series
Temperature
Humidity
Duration
Applied current
Recovery
: 60±2℃
: 90～95％RH
: 1000 hrs
: Rated current
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
20.High temperature life test
Specified Value
LB, LBC, LBR, LBMF Series
－
CB, CBC, CBL, CBMF Series
Inductance change : Within±10％
No significant abnormality in appearance.
LBM Series
Test Methods and
Remarks
Temperature
Duration
Recovery
: 85±2℃
: 1000 hrs
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
21.Loading at high temperature life test
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
LBM Series
Test Methods and
Remarks
Temperature
Duration
Applied current
Recovery
Inductance change : Within±10％
（LBC3225 Series : Within±20％）
No significant abnormality in appearance.
－
: 85±2℃
: 1000 hrs
: Rated current
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
22.Low temperature life test
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
Inductance change : Within±10％
No significant abnormality in appearance.
LBM Series
Test Methods and
Remarks
Temperature
Duration
Recovery
: －40±2℃
: 1000 hrs
: At least 2 hrs of recovery under the standard condition after the test, followed by the measurement within 48 hrs.
23.Standard condition
LB, LBC, LBR, LBMF Series
Specified Value
CB, CBC, CBL, CBMF Series
LBM Series
Standard test conditions
Unless specified, Ambient temperature is 20±15℃ and the Relative
humidity is 65±20％. If there is any doubt about the test results, further
measurement shall be had within the following limits:
Ambient Temperature: 20±2℃
Relative humidity: 65±5％
Inductance value is based on our standard measurement systems.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_reli_e-E05R01
WIRE-WOUND CHIP INDUCTORS (LB SERIES)，
WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES)，
WIRE-WOUND CHIP INDUCTORS FOR SIGNAL LINES (LB SERIES M TYPE)
■PRECAUTIONS
1．Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment, (office supply equipment,
telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical
equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear
control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or
damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2．PCB Design
Precautions
Technical
considerations
◆Land pattern design
1. Please contact any of our offices for a land pattern, and refer to a recommended land pattern of a right figure or specifications.
PRECAUTIONS
【Recommended Land Patterns】
Surface Mounting
・ Mounting and soldering conditions should be checked beforehand.
・ Applicable soldering process to those products is reflow soldering only.
3．Considerations for automatic placement
Precautions
Technical
considerations
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4．Soldering
Precautions
◆Reflow soldering（ LB and CB Types）
1. For reflow soldering with either leaded or lead-free solder, the profile specified in "point for controlling" is recommended.
◆Recommended conditions for using a soldering iron
1. Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350℃ Duration-3 seconds or less. The soldering iron
should not come in contact with inductor directly.
◆Reflow soldering（ LB and CB Types）
1. Reflow profile
Technical
considerations
◆Recommended conditions for using a soldering iron
1. Components can be damaged by excessive heat where soldering conditions exceed the specified range.
5．Cleaning
Precautions
Technical
considerations
◆Cleaning conditions
Washing by supersonic waves shall be avoided.
◆Cleaning conditions
If washed by supersonic waves, the products might be broken.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_prec_e-E06R01
6．Handling
Precautions
Technical
considerations
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Breakaway PC boards（ splitting along perforations）
1. When splitting the PC board after mounting inductors, care should be taken not to give any stresses of deflection or twisting to the
board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Breakaway PC boards（ splitting along perforations）
1. Planning pattern configurations and the position of products should be carefully performed to minimize stress.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
7．Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the
storage area should be controlled.
・ Recommended conditions
Ambient temperature : 0～40℃
Humidity : Below 70% RH
・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may
decrease as time passes.
For this reason, product should be used within 6 months from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
considerations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes
and deterioration of taping/packaging materials may take place.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_wound_CB_LB_prec_e-E06R01
工商网监
湘ICP备2023018690号
