0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
LHL13NB102J

LHL13NB102J

  • 厂商:

    TAIYO-YUDEN(太诱)

  • 封装:

    径向

  • 描述:

    FIXED IND 1MH 600MA 1.2 OHM TH

  • 详情介绍
  • 数据手册
  • 价格&库存
LHL13NB102J 数据手册
Notice for TAIYO YUDEN Products [ For General Electronic Equipment ] Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2018. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or use of our products. Please note that TAIYO YUDEN shall not be in any way responsible for any damages and defects in products or equipment incorporating our products, which are caused under the conditions other than those specified in this catalog or individual product specification sheets. ■ Please contact TAIYO YUDEN for further details of product specifications as the individual product specification sheets are available. ■ Please conduct validation and verification of our products in actual condition of mounting and operating environment before using our products. ■ The products listed in this catalog are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC) and medical equipment classified as Class I or II by IMDRF. Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment, disaster prevention equipment, medical equipment classified as Class III by IMDRF, highly public information network equipment including, without limitation, telephone exchange, and base station). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control equipment, undersea equipment, military equipment). *Note: There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to contact TAIYO YUDEN for further information before using our products for such aviation equipment. When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary. Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment requiring inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN as described above. ■ Information contained in this catalog is intended to convey examples of typical performances and/or applications of our products and is not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties nor grant any license under such rights. ■ Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in any way responsible for any damages resulting from a fault or defect in our products. Notwithstanding the foregoing, if there is a written agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will warrant our products in accordance with such agreement. ■ The contents of this catalog are applicable to our products which are purchased from our sales offices or authorized distributors (hereinafter“TAIYO YUDEN’ s official sales channel”). Please note that the contents of this catalog are not applicable to our products purchased from any seller other than TAIYO YUDEN’ s official sales channel. ■ Caution for Export Some of our products listed in this catalog may require specific procedures for export according to“U.S. Export Administration Regulations” ,“Foreign Exchange and Foreign Trade Control Law”of Japan, and other applicable regulations. Should you have any questions on this matter, please contact our sales staff. 19 RADIAL LEADED INDUCTORS RADIAL LEADED INDUCTORS WAVE WAVE ■PARTS NUMBER L H △ ① *Operating Temp. : -25~+105℃(Including self-generated heat) L △ ② ①Series name Code LH△ 0 8 ③ T B 1 0 1 ⑤ ④ K ⑥ ⑥Inductance tolerance Code J K M N Dimensions(D)[mm max.] 9.0 11.0 ④Packaging Code NB TB ⑦Internal code Code △△△ Packaging Bulk(LHL) Ammo packaging(LHL) Nominal inductance[μH] 1.0 15 1000 / LEADED INDUCTORS INDUCTORS Characteristics Standard type Taping available High current type ③Dimensions(D) Code 08 10 △=Blank space ⑤Nominal inductance Code (example) 1R0 150 102 ※R=Decimal point Series name Radial leaded inductor ②Characteristics Code L△ LC △ △ △ ⑦ Inductance tolerance ±5% ±10% ±20% ±30% Internal code Standard ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY LHL /LHLC D H2 d ℓ F LH LH LH LH Type D H2 ℓ F φd L 08 LC08 L 10 LC10 9.0 max (0.354 max) 11.0 max (0.433 max) 9.5 max (0.374 max) 14.0 max (0.551 max) 5.0±1.0 (0.197±0.039) 5.0±1.0 (0.197±0.039) 5.0±1.0 (0.197±0.039) 5.0±1.0 (0.197±0.039) 0.6±0.05 (0.024±0.002) 0.6±0.05 (0.024±0.002) Box - - Standard quantity [pcs] Bulk Taping 100 1000 50 500 Unit:mm(inch) i_leaded_LH_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 19 107 ■PARTS NUMBER ●LHL08 Parts number EHS Nominal inductance [μH] / LEADED INDUCTORS INDUCTORS LH L 08[]1R0N RoHS 1.0 LH L 08[]1R5M RoHS 1.5 LH L 08[]2R2M RoHS 2.2 LH L 08[]2R7M RoHS 2.7 LH L 08[]3R3M RoHS 3.3 LH L 08[]3R9M RoHS 3.9 LH L 08[]4R7M RoHS 4.7 LH L 08[]5R6M RoHS 5.6 LH L 08[]6R8M RoHS 6.8 LH L 08[]8R2M RoHS 8.2 LH L 08[]100K RoHS 10 LH L 08[]120K RoHS 12 LH L 08[]150K RoHS 15 LH L 08[]180K RoHS 18 LH L 08[]220K RoHS 22 LH L 08[]270K RoHS 27 LH L 08[]330K RoHS 33 LH L 08[]390K RoHS 39 LH L 08[]470K RoHS 47 LH L 08[]560K RoHS 56 LH L 08[]680K RoHS 68 LH L 08[]820K RoHS 82 LH L 08[]101K RoHS 100 LH L 08[]121K RoHS 120 LH L 08[]151K RoHS 150 LH L 08[]181K RoHS 180 LH L 08[]221K RoHS 220 LH L 08[]271K RoHS 270 LH L 08[]331K RoHS 330 LH L 08[]391K RoHS 390 LH L 08[]471K RoHS 470 LH L 08[]561K RoHS 560 LH L 08[]681K RoHS 680 LH L 08[]821K RoHS 820 LH L 08[]102J RoHS 1000 LH L 08[]122J RoHS 1200 LH L 08[]152J RoHS 1500 LH L 08[]182J RoHS 1800 LH L 08[]222J RoHS 2200 LH L 08[]272J RoHS 2700 LH L 08[]332J RoHS 3300 LH L 08[]392J RoHS 3900 LH L 08[]472J RoHS 4700 LH L 08[]562J RoHS 5600 LH L 08[]682J RoHS 6800 LH L 08[]822J RoHS 8200 LH L 08[]103J RoHS 10000 LH L 08[]123J RoHS 12000 LH L 08[]153J RoHS 15000 LH L 08[]183J RoHS 18000 LH L 08[]223J RoHS 22000 LH L 08[]273J RoHS 27000 LH L 08[]333J RoHS 33000 ・ [] Please specify the packaging code. (TB: Taping, NB: Bulk) Inductance tolerance Q (min.) Self-resonant frequency [MHz](min..) DC Resistance [Ω](max.) Rated current [A](max.) Measuring frequency [MHz] ±30% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% 40 40 40 40 40 40 40 40 40 40 65 65 50 50 50 50 40 40 40 40 35 35 25 25 20 35 35 25 25 20 25 25 25 30 55 45 55 55 55 55 55 55 65 65 65 65 60 60 60 60 60 60 60 76 65 56 48 41 33 30 23 21 19 17 16 13 12 11 10 8.8 8.4 8.2 7.9 7.0 6.5 5.7 5.2 4.7 4.2 3.7 3.5 3.2 2.9 2.4 2.2 2.0 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0.85 0.78 0.68 0.62 0.61 0.60 0.48 0.44 0.35 0.30 0.28 0.25 0.23 0.013 0.014 0.017 0.019 0.021 0.024 0.025 0.028 0.030 0.034 0.041 0.044 0.053 0.060 0.068 0.091 0.10 0.12 0.15 0.17 0.20 0.22 0.32 0.36 0.41 0.66 0.73 0.85 0.97 1.1 1.3 1.5 1.8 2.3 2.7 3.2 4.1 4.8 5.6 7.5 8.5 9.7 14 16 18 20 32 36 62 72 82 90 100 4.7 4.4 4.1 3.5 3.2 3.1 3.0 2.9 2.8 2.5 2.4 2.3 2.0 1.9 1.8 1.5 1.4 1.3 1.2 1.1 1.0 0.90 0.79 0.70 0.64 0.60 0.53 0.51 0.44 0.41 0.38 0.35 0.32 0.30 0.25 0.22 0.20 0.19 0.16 0.15 0.14 0.11 0.10 0.093 0.092 0.084 0.070 0.064 0.051 0.048 0.044 0.042 0.040 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz i_leaded_LH_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 108 19 ■PARTS NUMBER ●LHL10 Parts number EHS Nominal inductance [μH] Q (min.) Self-resonant frequency [MHz](min..) DC Resistance [Ω](max.) Rated current [A](max.) Measuring frequency [MHz] ±20% ±20% ±20% ±20% ±20% ±20% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% 50 50 50 50 50 50 90 90 90 90 60 60 60 60 50 50 40 40 40 40 40 40 40 30 30 30 30 30 30 30 50 50 50 50 50 50 50 50 50 50 50 50 60 60 60 60 60 40 40 40 40 30 30 30 30 30 30 46 40 38 34 30 24 19 16 12 9.2 8.6 7.1 6.8 6.7 6.2 5.2 4.9 4.7 3.8 3.2 2.9 2.6 2.3 2.1 2.0 1.8 1.7 1.5 1.4 1.3 1.2 0.87 0.83 0.75 0.70 0.67 0.56 0.54 0.49 0.41 0.38 0.36 0.29 0.27 0.24 0.21 0.20 0.15 0.14 0.13 0.12 0.10 0.095 0.088 0.085 0.070 0.069 0.019 0.022 0.024 0.025 0.028 0.031 0.034 0.038 0.042 0.046 0.061 0.069 0.078 0.085 0.093 0.10 0.12 0.13 0.18 0.25 0.29 0.40 0.44 0.50 0.56 0.62 0.84 0.93 1.0 1.4 1.8 2.3 2.7 3.0 3.9 4.3 5.8 6.4 7.1 9.0 10 12 19 21 34 38 43 67 76 84 96 170 200 210 240 260 300 4.2 4.1 4.0 3.8 3.4 3.3 3.2 2.8 2.6 2.4 2.1 2.0 1.9 1.8 1.7 1.6 1.5 1.4 1.2 1.0 0.95 0.80 0.75 0.70 0.68 0.63 0.57 0.52 0.48 0.42 0.41 0.33 0.30 0.29 0.25 0.24 0.21 0.20 0.19 0.17 0.16 0.15 0.12 0.11 0.090 0.081 0.075 0.060 0.056 0.053 0.050 0.036 0.035 0.033 0.031 0.030 0.028 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0252MHz L:1kHz, Q:0.0252MHz L:1kHz, Q:0.0252MHz / LEADED INDUCTORS INDUCTORS LH L 10[]3R3M RoHS 3.3 LH L 10[]3R9M RoHS 3.9 LH L 10[]4R7M RoHS 4.7 LH L 10[]5R6M RoHS 5.6 LH L 10[]6R8M RoHS 6.8 LH L 10[]8R2M RoHS 8.2 LH L 10[]100K RoHS 10 LH L 10[]120K RoHS 12 LH L 10[]150K RoHS 15 LH L 10[]180K RoHS 18 LH L 10[]220K RoHS 22 LH L 10[]270K RoHS 27 LH L 10[]330K RoHS 33 LH L 10[]390K RoHS 39 LH L 10[]470K RoHS 47 LH L 10[]560K RoHS 56 LH L 10[]680K RoHS 68 LH L 10[]820K RoHS 82 LH L 10[]101K RoHS 100 LH L 10[]121K RoHS 120 LH L 10[]151K RoHS 150 LH L 10[]181K RoHS 180 LH L 10[]221K RoHS 220 LH L 10[]271K RoHS 270 LH L 10[]331K RoHS 330 LH L 10[]391K RoHS 390 LH L 10[]471K RoHS 470 LH L 10[]561K RoHS 560 LH L 10[]681K RoHS 680 LH L 10[]821K RoHS 820 LH L 10[]102J RoHS 1000 LH L 10[]122J RoHS 1200 LH L 10[]152J RoHS 1500 LH L 10[]182J RoHS 1800 LH L 10[]222J RoHS 2200 LH L 10[]272J RoHS 2700 LH L 10[]332J RoHS 3300 LH L 10[]392J RoHS 3900 LH L 10[]472J RoHS 4700 LH L 10[]562J RoHS 5600 LH L 10[]682J RoHS 6800 LH L 10[]822J RoHS 8200 LH L 10[]103J RoHS 10000 LH L 10[]123J RoHS 12000 LH L 10[]153J RoHS 15000 LH L 10[]183J RoHS 18000 LH L 10[]223J RoHS 22000 LH L 10[]273J RoHS 27000 LH L 10[]333J RoHS 33000 LH L 10[]393J RoHS 39000 LH L 10[]473J RoHS 47000 LH L 10[]563J RoHS 56000 LH L 10[]683J RoHS 68000 LH L 10[]823J RoHS 82000 LH L 10[]104J RoHS 100000 LH L 10[]124J RoHS 120000 LH L 10[]154J RoHS 150000 ・ [] Please specify the packaging code. (TB: Taping, NB: Bulk) Inductance tolerance i_leaded_LH_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 19 109 ■PARTS NUMBER ●LHLC08 Parts number EHS Nominal inductance [μH] / LEADED INDUCTORS INDUCTORS LH LC08[]1R0N RoHS 1.0 LH LC08[]1R5M RoHS 1.5 LH LC08[]2R2M RoHS 2.2 LH LC08[]2R7M RoHS 2.7 LH LC08[]3R3M RoHS 3.3 LH LC08[]3R9M RoHS 3.9 LH LC08[]4R7M RoHS 4.7 LH LC08[]5R6M RoHS 5.6 LH LC08[]6R8M RoHS 6.8 LH LC08[]8R2M RoHS 8.2 LH LC08[]100K RoHS 10 LH LC08[]120K RoHS 12 LH LC08[]150K RoHS 15 LH LC08[]180K RoHS 18 LH LC08[]220K RoHS 22 LH LC08[]270K RoHS 27 LH LC08[]330K RoHS 33 LH LC08[]390K RoHS 39 LH LC08[]470K RoHS 47 LH LC08[]560K RoHS 56 LH LC08[]680K RoHS 68 LH LC08[]820K RoHS 82 LH LC08[]101K RoHS 100 LH LC08[]121K RoHS 120 LH LC08[]151K RoHS 150 LH LC08[]181K RoHS 180 LH LC08[]221K RoHS 220 LH LC08[]271K RoHS 270 LH LC08[]331K RoHS 330 LH LC08[]391K RoHS 390 LH LC08[]471K RoHS 470 LH LC08[]561K RoHS 560 LH LC08[]681K RoHS 680 LH LC08[]821K RoHS 820 LH LC08[]102J RoHS 1000 LH LC08[]122J RoHS 1200 LH LC08[]152J RoHS 1500 LH LC08[]182J RoHS 1800 LH LC08[]222J RoHS 2200 LH LC08[]272J RoHS 2700 LH LC08[]332J RoHS 3300 LH LC08[]392J RoHS 3900 LH LC08[]472J RoHS 4700 LH LC08[]562J RoHS 5600 LH LC08[]682J RoHS 6800 LH LC08[]822J RoHS 8200 LH LC08[]103J RoHS 10000 LH LC08[]123J RoHS 12000 LH LC08[]153J RoHS 15000 LH LC08[]183J RoHS 18000 LH LC08[]223J RoHS 22000 LH LC08[]273J RoHS 27000 LH LC08[]333J RoHS 33000 ・ [] Please specify the packaging code. (TB: Taping, NB: Bulk) Inductance tolerance Q (min.) Self-resonant frequency [MHz](min..) DC Resistance [Ω](max.) Rated current [A](max.) Measuring frequency [MHz] ±30% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% 40 40 40 40 40 40 40 40 40 40 65 65 50 50 50 50 40 40 40 40 35 35 25 25 20 35 35 25 25 20 25 25 25 30 55 45 55 55 55 55 55 55 65 65 65 65 60 60 60 60 60 60 60 76 65 56 48 41 33 30 23 21 19 17 16 13 12 11 10 8.8 8.4 8.2 7.9 7.0 6.5 5.7 5.2 4.7 4.2 3.7 3.5 3.2 2.9 2.4 2.2 2.0 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0.85 0.78 0.68 0.62 0.61 0.60 0.48 0.44 0.35 0.30 0.28 0.25 0.23 0.013 0.014 0.017 0.019 0.021 0.024 0.025 0.028 0.030 0.034 0.041 0.044 0.053 0.060 0.068 0.091 0.10 0.12 0.15 0.17 0.20 0.22 0.32 0.36 0.41 0.66 0.73 0.85 0.97 1.1 1.3 1.5 1.8 2.3 2.7 3.2 4.1 4.8 5.6 7.5 8.5 9.7 14 16 18 20 32 36 62 72 82 90 100 5.4 5.2 4.8 4.2 3.8 3.7 3.6 3.5 3.4 3.0 2.9 2.8 2.6 2.4 2.3 2.0 1.9 1.7 1.5 1.4 1.3 1.2 1.0 0.96 0.88 0.71 0.66 0.63 0.59 0.55 0.49 0.47 0.44 0.38 0.35 0.31 0.29 0.26 0.23 0.21 0.19 0.18 0.16 0.15 0.14 0.13 0.11 0.084 0.068 0.066 0.057 0.054 0.053 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz i_leaded_LH_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 110 19 ■PARTS NUMBER ●LHLC10 Parts number EHS Nominal inductance [μH] Q (min.) Self-resonant frequency [MHz](min..) DC Resistance [Ω](max.) Rated current [A](max.) Measuring frequency [MHz] ±20% ±20% ±20% ±20% ±20% ±20% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% 50 50 50 50 50 50 90 90 90 90 60 60 60 60 50 50 40 40 40 40 40 40 40 30 30 30 30 30 30 30 50 50 50 50 50 50 50 50 50 50 50 50 60 60 60 60 60 40 40 40 40 30 30 30 30 30 30 46 40 38 34 30 24 19 16 12 9.2 8.6 7.1 6.8 6.7 6.2 5.2 4.6 4.7 3.8 3.2 2.9 2.6 2.3 2.1 2.0 1.8 1.7 1.5 1.4 1.3 1.2 0.87 0.83 0.75 0.70 0.67 0.56 0.54 0.49 0.41 0.38 0.36 0.29 0.27 0.24 0.21 0.20 0.15 0.14 0.13 0.12 0.10 0.095 0.088 0.085 0.070 0.069 0.019 0.022 0.024 0.025 0.028 0.031 0.034 0.038 0.042 0.046 0.061 0.069 0.078 0.085 0.093 0.10 0.12 0.13 0.18 0.25 0.29 0.40 0.44 0.50 0.56 0.62 0.84 0.93 1.0 1.4 1.8 2.3 2.7 3.0 3.9 4.3 5.8 6.4 7.1 9.0 10 12 19 21 34 38 43 67 76 84 96 170 200 210 240 260 300 5.0 4.8 4.7 4.5 4.1 3.9 3.6 3.4 3.2 3.0 2.8 2.7 2.6 2.4 2.3 2.1 2.0 1.8 1.5 1.3 1.2 1.0 0.97 0.90 0.86 0.75 0.65 0.61 0.57 0.50 0.48 0.40 0.37 0.36 0.32 0.30 0.26 0.25 0.24 0.21 0.20 0.18 0.14 0.13 0.11 0.10 0.095 0.076 0.068 0.065 0.061 0.045 0.043 0.041 0.038 0.037 0.035 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0796MHz L:1kHz, Q:0.0252MHz L:1kHz, Q:0.0252MHz L:1kHz, Q:0.0252MHz / LEADED INDUCTORS INDUCTORS LH LC10[]3R3M RoHS 3.3 LH LC10[]3R9M RoHS 3.9 LH LC10[]4R7M RoHS 4.7 LH LC10[]5R6M RoHS 5.6 LH LC10[]6R8M RoHS 6.8 LH LC10[]8R2M RoHS 8.2 LH LC10[]100K RoHS 10 LH LC10[]120K RoHS 12 LH LC10[]150K RoHS 15 LH LC10[]180K RoHS 18 LH LC10[]220K RoHS 22 LH LC10[]270K RoHS 27 LH LC10[]330K RoHS 33 LH LC10[]390K RoHS 39 LH LC10[]470K RoHS 47 LH LC10[]560K RoHS 56 LH LC10[]680K RoHS 68 LH LC10[]820K RoHS 82 LH LC10[]101K RoHS 100 LH LC10[]121K RoHS 120 LH LC10[]151K RoHS 150 LH LC10[]181K RoHS 180 LH LC10[]221K RoHS 220 LH LC10[]271K RoHS 270 LH LC10[]331K RoHS 330 LH LC10[]391K RoHS 390 LH LC10[]471K RoHS 470 LH LC10[]561K RoHS 560 LH LC10[]681K RoHS 680 LH LC10[]821K RoHS 820 LH LC10[]102J RoHS 1000 LH LC10[]122J RoHS 1200 LH LC10[]152J RoHS 1500 LH LC10[]182J RoHS 1800 LH LC10[]222J RoHS 2200 LH LC10[]272J RoHS 2700 LH LC10[]332J RoHS 3300 LH LC10[]392J RoHS 3900 LH LC10[]472J RoHS 4700 LH LC10[]562J RoHS 5600 LH LC10[]682J RoHS 6800 LH LC10[]822J RoHS 8200 LH LC10[]103J RoHS 10000 LH LC10[]123J RoHS 12000 LH LC10[]153J RoHS 15000 LH LC10[]183J RoHS 18000 LH LC10[]223J RoHS 22000 LH LC10[]273J RoHS 27000 LH LC10[]333J RoHS 33000 LH LC10[]393J RoHS 39000 LH LC10[]473J RoHS 47000 LH LC10[]563J RoHS 56000 LH LC10[]683J RoHS 68000 LH LC10[]823J RoHS 82000 LH LC10[]104J RoHS 100000 LH LC10[]124J RoHS 120000 LH LC10[]154J RoHS 150000 ・ [] Please specify the packaging code. (TB: Taping, NB: Bulk) Inductance tolerance i_leaded_LH_e-E05R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 19 111 RADIAL LEADED INDUCTORS ■PACKAGING ①Minimum Quantity Standard quantity [pcs] Bulk Taped 100 1000 50 500 100 1000 50 500 Type (EIA) LHL 08 LHL 10 LHLC08 LHLC10 ②Bulk dimensions ●LHL08, LHL10 Type LHL08 LHL10 φD(max) 9.0 (0.354) 11.0 (0.433) Dimensions F* 5.0±1.0 (0.197±0.039) 5.0±1.0 (0.197±0.039) H2(max) 9.5 (0.374) 14.0 (0.551) ℓ 5.0±1.0 (0.197±0.039) 5.0±1.0 (0.197±0.039) φd 0.6±0.05 (0.024±0.002) 0.6±0.05 (0.024±0.002) Unit:mm(inch) *Measured at the base of the leads. D H1 H H2 P P0 P1 P2 F h W W0 W1 W2 D0 φd t LHL08 φ9.0 max (φ0.354 max) 30.5 max (1.20 max) 18.0+2.0/-0.0 (0.709+0.079/-0.000) 9.5 max (0.374 max) 12.7±1.0 (0.500±0.039) 12.7±0.3※1 (0.500±0.012) 3.85±0.7 (0.152±0.028) 6.35±1.3 (0.250±0.051) 5.0+0.8/-0.2 (0.197+0.031/0.008) 0.0±2.0 (0.0±0.079) 18.0+1.0/-0.5 (0.709+0.039/-0.020) 12.5 min (0.492 min) 9.0±0.5 (0.354±0.020) 3.0 max※2 (0.118 max) φ4.0±0.2 (φ0.158±0.008) φ0.6±0.05 (φ0.024±0.002) 0.6±0.3 (0.024±0.012) LHL10 φ11.0 max (φ0.433 max) 34.0 max (1.34 max) 18.0+2.0/-0.0 (0.709+0.079/-0.000) 14.0 max (0.551 max) 12.7±1.0 (0.500±0.039) 12.7±0.3※1 (0.500±0.012) 3.85±0.7 (0.152±0.028) 6.35±1.3 (0.250±0.051) 5.0+0.8/-0.2 (0.197+0.031/-0.008) 0.0±2.0 (0.0±0.079) 18.0+1.0/-0.5 (0.709+0.039/-0.020) 12.5 min (0.492 min) 9.0±0.5 (0.354±0.020) 3.0 max※2 (0.118 max) φ4.0±0.2 (φ0.158±0.008) φ0.6±0.05 (φ0.024±0.002) 0.6±0.3 (0.024±0.012) Unit:mm(inch) ※1 Accumulated error for 20 pitches is 1mm. ※2 Bonding tape must not protrude from the base tape. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_LH_pack_e-E04R01 ●LHLC08, LHLC10 Type LHLC08 LHLC10 φD(max) 9.0 (0.354) 11.0 (0.433) Dimensions F* 5.0±1.0 (0.197±0.039) 5.0±1.0 (0.197±0.039) H2(max) 9.5 (0.374) 14.0 (0.551) ℓ 5.0±1.0 (0.197±0.039) 5.0±1.0 (0.197±0.039) φd 0.6±0.05 (0.024±0.002) 0.6±0.05 (0.024±0.002) Unit:mm(inch) *Measured at the base of the leads. D H1 H H2 P P0 P1 P2 F H W W0 W1 W2 D0 φd t LHLC08 φ9.0max (φ0.354max) 30.5max (1.20max) 18.0+2.0/-0.0 (0.709+0.079/-0.000) 9.5max (0.374max) 12.7±1.0 (0.500±0.039) 12.7±0.3※1 (0.500±0.012) 3.85±0.7 (0.152±0.028) 6.35±1.3 (0.250±0.051) 5.0+0.8/-0.2 (0.197+0.031/-0.008) 0.0±2.0 (0.0±0.079) 18.0+1.0/-0.5 (0.709+0.039/-0.020) 12.5min (0.492min) 9.0±0.5 (0.354±0.020) 3.0max※2 (0.118max) φ4.0±0.2 (φ0.158±0.008) φ0.6±0.05 (φ0.024±0.002) 0.6±0.3 (0.024±0.012) LHLC10 φ11.0max (φ0433max) 34.0max (1.34max) 18.0+2.0/-0.0 (0.709+0.079/-0.000) 14.0max (0.551max) 12.7±1.0 (0.500±0.039) 12.7±0.3※1 (0.500±0.012) 3.85±0.7 (0.152±0.028) 6.35±1.3 (0.250±0.051) 5.0+0.8/-0.2 (0.197+0.031/-0.008) 0.0±2.0 (0.0±0.079) 18.0+1.0/-0.5 (0.709+0.039/-0.020) 12.5min (0.492min) 9.0±0.5 (0.354±0.020) 3.0max※2 (0.118max) φ4.0±0.2 (φ0.158±0.008) φ0.6±0.05 (φ0.024±0.002) 0.6±0.3 (0.024±0.012) Unit:mm(inch) ※1 Accumulated error for 20 pitches is 1mm. ※2 Bonding tape must not protrude from the base tape. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_LH_pack_e-E04R01 AXIAL LEADED INDUCTORS(CAL Type)、 RADIAL LEADED INDUCTORS(LH Type)、 LEADED FERRITE BEAD INDUCTORS( FB Series A Type/R Type) ■RELIABILITY DATA 1. Operating temperature Range CAL45 Type Specified Value LHL□□□ -25~+ 105℃ FBA/FBR CAL45 Type Test Methods and Remarks LHL□□□ Including self-generated heat FBA/FBR 2. Storage temperature Range CAL45 Type Specified Value LHL□□□ -40~+ 85℃(Except for taping condition) FBA/FBR 3. Rated current CAL45 Type Specified Value LHL□□□ Within the specified tolerance FBA/FBR Test Methods and Remarks CAL45 Type : The maximum DC value having inductance within 10% and temperature increase within 40℃ by the application of DC bias. LHL□□□ : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10:within 30%) and temperature increase within the following specified temperature by the application of DC bias. Reference temperature : 25℃(LHL08, LHL10) : 40℃(LHLC08, LHLC10) FBA/FBR : No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within ±20% of the initial value. This is not guaranteed for electrical characteristics during current application. 4. Impedance CAL45 Type Specified Value LHL□□□ FBA/FBR Test Methods and Remarks FBA/FBR : Measuring equipment Measuring frequency Within the specified tolerance : Impedance analyzer (HP4191A) or its equivalent : Specified frequency 5. Inductance CAL45 Type Specified Value LHL□□□ Within the specified tolerance FBA/FBR Test Methods and Remarks CAL45 Type : Measuring equipment Measuring frequency LHL□□□ : Measuring equipment Measuring frequency : LCR meter (HP4285A + HP42851A or its equivalent) : Specified frequency : LCR meter (HP4285A+HP42851A or its equivalent) : LCR meter (HP4263A) or its equivalent (at 1kHz) : Specified frequency ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E06R01 6. Q CAL45 Type Specified Value LHL□□□ Within the specified tolerance FBA/FBR Test Methods and Remarks LHL□□□ Measuring equipment Measuring frequency : LCR meter (HP4285A+HP42851A or its equivalent) : LCR meter (HP4263A) or its equivalent (at 1kHz) : Specified frequency 7. DC Resistance CAL45 Type Specified Value LHL□□□ Within the specified tolerance FBA/FBR Test Methods and Remarks Measuring equipment : DC ohmmeter 8. Self resonance frequency CAL45 Type Specified Value LHL□□□ Within the specified tolerance FBA/FBR Test Methods and Remarks LHL□□□ Measuring equipment : (HP4191A, 4192A) its equivalent 9. Temperature characteristic CAL45 Type Specified Value LHL□□□ △L/L : Within ±7% FBA/FBR Test Methods and Remarks Change of maximum inductance deviation in step 1 to 5 Temperature (℃) Step LHL□□□ 1 20 2 Minimum operating temperature 3 20 (Standard temperature) 4 Maximum operating temperature 5 20 10. Tensile strength test CAL45 Type Specified Value LHL□□□ No abnormality such as cut lead, or looseness. FBA/FBR Test Methods and Remarks CAL45 Type : Apply the stated tensile force progressively in the direction to draw terminal. force (N) duration (s) 10 10 LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal. Nominal wire diameter tensile φd (mm) force (N) duration (s) 0.3<φd≦0.5 5 30±5 0.5<φd≦0.8 10 0.8<φd≦1.2 25 FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the of the component during 10±1 seconds. axial direction ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E06R01 11. Over current Specified Value CAL45 Type No emission of smoke no firing. LHL□□□ There shall be no scorch or short of wire. LHLC08, LHLC10 : There shall be no firing. FBA/FBR Test Methods and Remarks LHL□□□・CAL45 Type : Measuring current : Rated current×2 Duration : 5 min. Number of measuring : one time 12. Terminal strength : bending CAL45 Type Specified Value LHL□□□ No abnormality such as cut lead, or looseness. FBA/FBR CAL45 Type : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter Mass reference Bending force tensile weight 0.3< φ d≦0.5 2.5 0.25 0.5< φ d≦0.8 5 0.50 Test Methods and Remarks LHL□□□・FBA/FBR : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter Mass reference Bending force tensile weight 0.3<φd≦0.5 2.5 0.25 0.5<φd≦0.8 5 0.5 0.8<φd≦1.2 10 1.0 13. Insulation resistance : between the terminals and body CAL45 Type Specified Value LHL□□□ 100MΩmin. FBA/FBR Test Methods and Remarks LHL□□□ : Applied voltage Duration : 500 VDC : 60 sec. 14. Insulation resistance : between terminals and core CAL45 Type Specified Value LHL□□□ FBA/FBR Test Methods and Remarks FBA/FBR : Applied voltage Duration 1MΩmin. : 100 VDC : 60±5 sec. 15. Withstanding : between the terminals and body CAL45 Type Specified Value LHL□□□ No abnormality such as insulation damage FBA/FBR Test Methods and Remarks LHL□□□ : According to JIS C5101-1. Metal global method Applied voltage : 500 VDC Duration : 60 sec. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E06R01 16. DC bias characteristic CAL45 Type Specified Value △L/L : Within -10% LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Measure inductance with application of rated current using LCR meter to compare it with the initial value. 17. Body strength CAL45 Type Specified Value No abnormality as damage. LHL□□□ FBA/FBR CAL45 Type : Applied force Duration Speed FBA : Applied force Duration No abnormality such as cracks on body. :50N : 10 sec. : Shall attain to specified force in 2 sec. : 50±3N : 30±1 sec. Test Methods and Remarks 18. Resistance to vibration Specified Value Test Methods and Remarks CAL45 Type △L/L : Within ±5% LHL□□□ Appearance : No abnormality △L/L : Within ±5% Q change : Within ±30% FBA/FBR Appearance : No abnormality Impedance change : Within ±20% CAL45 Type : Directions : 2 hrs each in X, Y and Z directions total : 6hrs. Frequency range : 10 to 55 to 10Hz (1min.) Amplitude : 1.5mm Mounting method : Soldering onto printed board. Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs. LHL□□□・FBA/FBR : Directions : 2 hrs each in X, Y and Z directions total : 6hrs. Frequency range : 10 to 55 to 10Hz (1min.) Amplitude : 1.5mm Mounting method : Soldering onto printed board. 19. Resistance to shock CAL45 Type Specified Value No significant abnormality in appearance LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Drop test Impact material Height Total number of drops : concrete or vinyl tile : 1m : 10 times ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E06R01 20. Solderability Specified Value Test Methods and Remarks CAL45 Type At least 75% of terminal electrode is covered by new solder. LHL□□□ At least 75% of terminal electrode is covered by new solder. FBA/FBR At least 90% of terminal electrode is covered by new solder. CAL45 Type : Solder temperature Duration LHL□□□ : Solder temperature Duration Immersion depth FBA/FBR : Solder temperature Duration Immersion depth : 230±5℃ : 2±0.5 sec. : 235±5℃ : 2±0.5 sec. : Up to 1.5mm from bottom of case. : 230±5℃ : 3±1 sec. : Up to 1.5mm from terminal root. 21. Resistance to soldering heat Specified Value CAL45 Type △L/L : Within ±5% LHL□□□ No significant abnormality in appearance Inductance change : Within ±5% Q change : Within ±30% FBA/FBR No significant abnormality in appearance Impedance change : Within ±20% CAL45 Type : Solder temperature Duration Immersed conditions Recovery : : : : LHL□□□ : Solder bath method : 270±5℃ 5±0.5 sec. One time Inserted into substrate with t=1.6mm At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs. Solder temperature Duration Manual soldering : Caution Recovery : : : : : : : : 260±5℃ 10±1 sec. Up to 1.5mm from the bottom of case. 350±10℃ (At the tip of soldering iron) 5±1 sec. Up to 1.5mm from the bottom of case. No excessive pressing shall be applied to terminals. 1 to 2hrs of recovery under the standard condition after the test. Solder temperature Duration Immersion depth Solder temperature Duration Immersion depth Recovery : : : : : : : 260±5℃ 10±1 sec. Up to 1.5mm from the terminal root. 350±5℃ 3±1 sec. Up to 1.5mm from the terminal root. 3hrs of recovery under the standard condition after the test. Solder temperature Duration Test Methods and Remarks FBA/FBR : Solder bath method: Condition 1: Condition 2 : 22. Resistance to solvent CAL45 Type Specified Value Please avoid the ultrasonic cleaning of this product. LHL□□□ No significant abnormality in appearance Impedance change : Within ±20% FBA/FBR Test Methods and Remarks FBA/FBR : Solvent temperature Duration Solvent type Recovery : : : : 20~25℃ 30±5 sec. Acetone 3hrs of recovery under the standard condition after the test. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E06R01 23. Thermal shock Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% FBA/FBR Appearance : No abnormality Impedance change : Within ±20% CAL45 Type:Conditions for 1cycle Step Temperature (℃) 1 -25+0/-3 2 Room temperature 3 +85+2/-0 4 Room temperature Number of cycles Recovery Test Methods and Remarks Duration (min.) 30±3 Within 3 30±3 Within 3 : 5 cycles : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. LHL□□□・FBA/FBR: According to JIS C60068-2-14. Conditions for 1 cycle Step Temperature (℃) 1 Minimum operating temperature 2 Room temperature 3 Maximum operating temperature 4 Room temperature Number of cycles Recovery : : : : Duration (min.) 30±3 Within 3 30±3 Within 3 10 cycles 〔LHL□□□〕 5 cycles (FBA/ FBR) 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 〔LHL□□□〕 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA/ FBR) 24. Damp heat CAL45 Type Specified Value △L/L : Within ±10% LHL□□□ Appearance:No abnormality Impedance change:Within ±20% FBA/FBR Test Methods and Remarks CAL45 Type : Temperature Humidity Duration Recovery FBA/FBR : Temperature Humidity Duration Recovery : 40±2℃ : 90~95%RH : 1000 hrs : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. : : : : 60±2℃ 90~95%RH 1000 hrs 3hrs of recovery under the standard condition after the removal from the test chamber. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E06R01 25. Loading under damp heat Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% FBA/FBR Test Methods and Remarks CAL45 Type : Temperature Humidity Duration Applied current Recovery LHL□□□ : Temperature Humidity Duration Applied current Recovery : 40±2℃ : 90~95%RH : 1000 hrs : Rated current : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. : : : : : 40±2℃ 90~95%RH 1000+48/-0 hrs Rated current 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 26. Loading at high temperature CAL45 Type Specified Value △L/L : Within ±10% LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Temperature Duration Applied current Recovery : 85±2℃ : 1000 hrs : Rated current : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. 27. Low temperature life test Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% FBA/FBR Test Methods and Remarks CAL45 Type : Temperature Duration Recovery LHL□□□ : Temperature Duration Recovery : -25±2℃ : 1000 hrs : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. :-40±3℃ : 1000+48/-0 hrs : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 28. High temperature life test CAL45 Type Specified Value LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% FBA/FBR Test Methods and Remarks LHL□□□ : Temperature Duration Recovery : 105±2℃ : 1000+48/-0 hrs : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E06R01 AXIAL LEADED INDUCTORS(CAL Type)、 RADIAL LEADED INDUCTORS(LH Type)、 LEADED FERRITE BEAD INDUCTORS(FB Series A Type/R Type) ■PRECAUTIONS 1. Circuit Design Precautions ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Precautions Technical considerations ◆Design 1. Please design insertion pitches as matching to that of leads of the component on PCBs. ◆Design 1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs. 3. Considerations for automatic placement Precautions Technical considerations ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. ◆Adjustment of mounting machine 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 4. Soldering Precautions ◆Wave soldering 1. Please refer to the specifications in the catalog for a wave soldering. 2. Do not immerse the entire inductor in the flux during the soldering operation. ◆Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc sufficiently. ◆Recommended conditions for using a soldering iron: ・Put the soldering iron on the land-pattern. ・Soldering iron's temperature - Below 350℃ ・Duration - 3 seconds or less ・The soldering iron should not directly touch the inductor. ◆Reflow soldering 1. As for reflow soldering, please contact our sales staff. Technical considerations ◆Lead free soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. ◆Recommended conditions for using a soldering iron If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. 5. Cleaning Precautions Technical considerations ◆Cleaning conditions 1. CAL type, LH type Please do not do cleaning by a supersonic wave. ◆Cleaning conditions 1. CAL type, LH type, If washing by supersonic waves, supersonic waves may deform products. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_prec_e-E02R01 6. Handling Precautions Technical considerations ◆Handling 1. Keep the inductors away from all magnets and magnetic objects. ◆Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. 2. LH type If inductors are dropped onto the floor or a hard surface they should not be used. ◆Packing 1. Please do not give the inductors any excessive mechanical shocks. In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item). ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 2. LH type There is a case to be broken by a fall. ◆Packing 1. There is a case that a lead wire could be deformed by a fall or an excessive shock. 7. Storage conditions Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions ・Ambient temperature 0~40℃ ・Humidity Below 70% RH The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, inductors should be used within one year from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical considerations ◆Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_prec_e-E02R01
LHL13NB102J
1. 物料型号:文档列出了多种型号的径向引脚电感器(RADIAL LEADED INDUCTORS),包括LHL系列和LHLC系列。

2. 器件简介:太诱电感器适用于一般电子设备,如音视频设备、办公设备、家用电器、信息通信设备等。不适用于可能直接导致人员伤亡的设备,如交通设备、医疗设备等。

3. 引脚分配:文档提供了电感器的引脚分配信息,包括引脚直径、高度等。

4. 参数特性:包括电感值、公差、Q值、自谐振频率、直流电阻、额定电流等。

5. 功能详解:文档提供了电感器的功能描述,如它们在电路中的作用和重要性。

6. 应用信息:电感器的应用范围,包括在一般电子设备中的使用。

7. 封装信息:详细列出了不同型号电感器的封装尺寸和包装信息。

8. 可靠性数据:包括工作温度范围、存储温度范围、额定电流、阻抗、电感、Q值、直流电阻、自谐振频率、温度特性等测试方法和规格值。

9. 其他信息:还包括了焊接性、耐热性、耐振性、耐冲击性、耐溶剂性等测试数据。
LHL13NB102J 价格&库存

很抱歉,暂时无法提供与“LHL13NB102J”相匹配的价格&库存,您可以联系我们找货

免费人工找货