B32652A7273J000

Film Capacitor Metallized Polypropylene Film Capacitor (MKP) Series/Type: Ordering code: B32652A7 * B32652A7273J Date: Version: 2012-05-22 1 Content of header bars 1 and 2 of data sheet will be automatically entered in headers and footers! Please fill in the table and then change the color to "white". This ensures that the table disappears (invisible) for the customer PDF. Don't change formatting when entering or pasting text in the table and don't add any cell or line in and to it! Identification/Classification 1 (header 1 + top left bar): Film Capacitor Identification/Classification 2 (header 2 + bottom left header bar): Metallized Polypropylene Film Capacitor (MKP) Ordering code: (top right header bar) B32652A7273J Series/Type: (bottom right header bar) B32652A7 * Preliminary data (optional): (if necessary) Department: FILM PD Date: 2012-05-22 Version: 1 Prepared by: Huining Lu Release signed by: Eduardo Drehmer Release signed QS: Ally Wang  EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Film Capacitor Metallized Polypropylene Film Capacitor (MKP) Applications

B32652A7273J B32652A7 * Drawing Electronic ballasts (resonant circuits) Switch-mode power supplies Climatic

Max. operating temperature: 110°C Climatic category (IEC 60068-1): 55/100/56 Construction



Dielectric: polypropylene (PP) Wound capacitor technology plastic case (UL 94 V-0) Epoxy resin sealing Features

High pulse strength High contact reliability Terminals

Parallel wire leads Lead-free tinned Marking





Manufacturer’s logo Lot number, series number Rated capacitance (coded) Cap. Tolerance (code letter) Rated DC voltage Date of manufacture (coded) Delivery mode
Bulk Dimensions





Lead spacing (e): Width max. (w): Height max. (h): Length max. (l): Lead diameter : Lead length: 15.0 ± 0.4 9.0 17.5 18.0 0.8 ± 0.05 6–1 mm mm mm mm mm mm FILM PD Please read Cautions and warnings and Important notes at the end of this document. 2012-05-22 Page 2 of 5 Film Capacitor Metallized Polypropylene Film Capacitor (MKP) B32652A7273J B32652A7 * Technical data Operating temperature range Max. operating temperature Top, max +110 °C Upper category temperature Tmax +100 °C Lower category temperature Tmin -55 °C Rated temperature TR +85°C Rated Capacitance C 27 nF Capacitance tolerance ± 5 % (J) Rated DC voltage Urdc 1250 V DC Rated AC voltage Urac 500 V AC -3 Dissipation factor tan δ (in 10 ) at 20°C (upper limit values) ≤ 0.8 Pulse handling capability (dV/dt) 1850 V/µs Pulse characteristic K0 9 000 000 V²/µs (at 1 kHz) Insulation resistance Rins at 20 °C, rel. humidity ≤ 65% ≥ 100 GΩ (minimum as-delivered values) Category voltage VC TA (°C) DC voltage derating AC voltage derating (continuous operation with VDC or VAC at f ≤ 1 KHz) TA ≤ 85 VC = VR VC,RMS = VRMS 85 < TA ≤ 110 VC = VR · (165-TA) / 80 VC,RMS = VRMS · (165-TA) / 80 FILM PD Please read Cautions and warnings and Important notes at the end of this document. 2012-05-22 Page 3 of 5 Film Capacitor Metallized Polypropylene Film Capacitor (MKP) B32652A7273J B32652A7 * Cautions and warning
Do not exceed the upper category temperature (UCT).
Do not apply any mechanical stress to the capacitor terminals.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after it has been soldered to the PC board.
Do not pick up the PC board by the soldered capacitor.
Do not place the capacitor on a PC board whose PTH hole spacing differs from the specified lead spacing.
Do not exceed the specified time or temperature limits during soldering.
Avoid external energy inputs, such as fire or electricity.
Avoid overload of the capacitors. The table below summarizes the safety instructions that must always be observed. A detailed description can be found in the relevant sections of the chapters "General technical information" and "Mounting guidelines". Topic Safety information Storage conditions Make sure that capacitors are stored within the specified range of time, temperature and humidity conditions. Avoid external energy, such as fire or electricity (passive flammability), avoid overload of the capacitors (active flammability) and consider the flammability of materials. Do not exceed the tested ability to withstand vibration. The capacitors are tested to IEC 60068-2-6. EPCOS offers film capacitors specially designed for operation under more severe vibration regimes such as those found in automotive applications. Consult our catalog "Film Capacitors for Automotive Electronics". Safety information 5.2 "Resistance to vibration" Do not exceed the specified time or temperature limits during soldering. Use only suitable solvents for cleaning capacitors. When embedding finished circuit assemblies in plastic resins, chemical and thermal influences must be taken into account. Caution: Consult us first, if you also wish to embed other uncoated component types! 2 "Cleaning" 3 "Embedding of capacitors in finished assemblies" Flammability Resistance to vibration Topic Soldering Cleaning Embedding of capacitors in finished assemblies FILM PD Please read Cautions and warnings and Important notes at the end of this document. Reference chapter "General technical information" 4.5 "Storage conditions" 5.3 "Flammability" Reference chapter "Mounting guidelines" 1 "Soldering" 2012-05-22 Page 4 of 5 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 5 of 5