U880B

U880B Double Flasher Description The bipolar circuit, U880B, is designed as a double flasher for wide range of applications. It has polarity and short-circuit protected stages for timely coupled outputs. Features D Integrated oscillator D fnominal = 3.3 Hz D Supply voltage range: 4.75 to 20.4 V D Polarity protected D Two protected power stages D Output current, 55 mA nominal Case: TO 50 +V S Applications D Toys D Roboter D LED switching 4 Oscillator T frequency R divider 3 Q2 Supply Limitation V – On R R Output logic 1 Temperature protection Q1 2 95 9962 –VS Figure 1. Block diagram with application Pin Description Pin Pin 1 Pin 3 Symbol O1 O2 Function Output O1 Output O2 Pin Pin 2 Pin 4 Symbol –VS VS Function Supply, GND Supply TELEFUNKEN Semiconductors Rev. A1, 22-Apr-96 1 (4) U880B Absolute Maximum Ratings Reference point Pin 2, unless otherwise specified Parameters Supply current Peak supply current t ≤ 10 ms Supply voltage Output stage Peak current t ≤ 1 ms; Ptot ≤ 200 mW Power dissipation Tamb = 45 °C Tamb = 100 °C Storage temperature range Ambient temperature range Tstg Tamb Pin 4 Pin 4 Pin 4 Pin 1, 3 Pin 1, 3 Symbol IS IS ±VS VO IO –IO Ptot Value 30 150 20.4 20.4 100 150 200 80 –40 to +125 –10 to +100 °C °C Unit mA mA V V mA mW Electrical Characteristics Reference point Pin 2, VS = 9, Tamb = 25 °C, unless otherwise specified Parameters Supply current Test Conditions / Pin Pin 4 V4 min = 4.75 V V4 = 9.0 V V4 max = 20.4 V I4 = 10 mA Pin 4 Pin 4 Symbol IS Min Typ 3.2 3.3 3.8 20.8 4.2 3.0 3.8 0.025 2.0 0.025 0.5 1.0 250 35 20.4 –1.1 130 145 55 50 0.5 700 80 mV mA %/K V Max 4.9 5.0 6.5 24.2 4.75 Unit mA Supply voltage limitation Voltage monitoring ON–Threshold OFF–Threshold Output stage Temperature coefficient Oscillator Clock frequency Temperature coefficient Voltage coefficient Output stage Saturation voltage Current limitation Temperature coefficient Voltage limitation Leakage current Over temperature limitation ti V4 V4 V4 V4 TC V V V V %/K Hz %/K %/V Switched off Pins 1 and 3 Tj = 45 °C Tj = 100 °C f TC VC 4.0 Pins 1 and 3 V4 = 6.0 V; Io = 25 mA VO V4 = 8 V; V1,3 = 7.5 V IO V4 = 9 V; V1,3 = 2.0 V TC –IO = 1 mA VO IO = 30 mA V1,3 = 10 V Pin 1, 3 IO V4 = 5 V Tj V4 = 9 V 24.2 –0.4 20 mA °C 2 (4) TELEFUNKEN Semiconductors Rev. A1, 22-Apr-96 U880B Dimensions in mm Package: JEDEC TO 50 94 9282 0.9 2.7 2.3 3 1.5 1.2 5.0 4.5 1.5 0.45 max. 4 6.1 5.9 2 0.6 5.0 4.6 9.0 8.0 technical drawings according to DIN specifications 1 1.1 0.9 0.2 TELEFUNKEN Semiconductors Rev. A1, 22-Apr-96 3 (4) U880B Ozone Depleting Substances Policy Statement It is the policy of TEMIC TELEFUNKEN microelectronic GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances ( ODSs). The Montreal Protocol ( 1987) and its London Amendments ( 1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. TEMIC TELEFUNKEN microelectronic GmbH semiconductor division has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2 . Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency ( EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C ( transitional substances ) respectively. TEMIC can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use TEMIC products for any unintended or unauthorized application, the buyer shall indemnify TEMIC against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. TEMIC TELEFUNKEN microelectronic GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 ( 0 ) 7131 67 2831, Fax number: 49 ( 0 ) 7131 67 2423 4 (4) TELEFUNKEN Semiconductors Rev. A1, 22-Apr-96