BFC23837BFC2

Not for New Designs - Alternative Device: New MKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type 168x12(halfpage) l w FEATURES w l h 7.5 mm bent back pitch. 15 mm to 27.5 mm lead pitch. Low contact resistance. Low loss dielectric. Small dimensions for high density packaging. Supplied loose in box and taped on reel h h' F' (1) F lt P ¯dt H ¯dt 10 15 Dimensions in mm Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 ENCAPSULATION Plastic case, epoxy resin sealed, flame retardant UL-class 94 V-0 (1) F - F’ 0.3 mm F = 7.5 + 0.6/- 0.1 mm  CLIMATIC CATEGORY APPLICATIONS 55/105/56 Where steep pulses occur e.g. SMPS (switch mode power supplies). Electronic lighting e.g. Ballast. Motor control circuits. S-correction. For flyback applications please use 1400 V series.  CAPACITANCE RANGE (E24 SERIES) 0.001 µF to 2.7 µF REFERENCE SPECIFICATIONS  CAPACITANCE TOLERANCE IEC 60384-17 ±5%  LEADS MARKING C-value; tolerance; rated voltage; sub-class; manufacturer’s type; code for dielectric material; code for factory of origin; manufacturer; year and week of manufacture Tinned wire DIELECTRIC 85 °C  RATED (DC) TEMPERATURE Polypropylene film  RATED (AC) TEMPERATURE ELECTRODES 105 °C Metallized MAXIMUM APPLICATION TEMPERATURE ENCAPSULATION 105 C Flame retardant plastic case and epoxy resin CONSTRUCTION  DETAIL SPECIFICATION For more detailed data and test requirements contact: dc-film@vishay.com Internal serial construction RATED (DC) VOLTAGE 250 V, 400 V, 630 V, 1000 V, 1400 V, 1600 V, 2000 V, 2500 V RATED (AC) VOLTAGE 125 V, 200 V, 220 V, 350 V, 500 V, 550 V, 700 V, 900 V RATED PEAK-TO-PEAK VOLTAGE 350 V, 560 V, 630 V, 1000 V, 1400 V, 1600 V, 2000 V, 2500 V Document Number: 28124 Revision: 08-Aug-2018 For technical questions, contact: dc-film@vishay.com www.vishay.com 187 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type COMPOSITION OF CATALOG NUMBER TYPE AND PITCHES 15.0 mm/7.5 mm 383 MULTIPLIER (nF) CAPACITANCE (numerically) 22.5 mm 27.5 mm BFC2 2222 (1) (1) Old TYPE 383 0.1 2 1 3 Example: 10 4 104  10 x 10  100 nF 100 5 1600 V 2000 V 2500 V 50 53 60 63 70 - 15.0 mm PACKAGING Loose in box Taped on reel (bent back to  7.5 mm) (1) 383 383 XX YY Y XX YY Y ordering code LEAD CONFIGURATION PREFERRED TYPES C-TOL. 250 V Lead length 3.5 mm ± 0.3 mm ±5% H  16.0 mm; P0  15.0 mm reel diameter  500 mm ±5 % Loose in box Lead length 5.0 mm ± 1.0 mm Lead length 25.0 mm ± 2.0 mm ±5 % ±5 % Taped on reel H  18.5 mm; P0  12.7 mm ±5 % 00 03 400 V 630 V 10 13 20 23 1000 V 1 400 V 30 33 40 43 Dimensions of this code numbers stay between brackets ON REQUEST (1) 383 Taped on reel (bent back to  7.5 mm) (1) Taped on reel (bent back to 10.0 mm) (1) H  16.0 mm; P0  15.0 mm reel diameter  356 mm ±5 % H  16.0 mm; P0  15.0 mm reel diameter  500 mm ±5 % 01 04 11 14 21 24 31 34 41 44 51 54 61 64 71 74 02 12 22 32 42 52 62 72 05 15 25 35 45 55 65 - Dimensions of this code numbers stay between brackets 08 18 28 38 48 58 68 - Note (1) For detailed tape specifications refer to “Packaging Information” www. vishay.com/doc?28139 or end of catalog SPECIFIC REFERENCE DATA (250 Vdc) DESCRIPTION Tangent of loss angle: C  0.15 µF 0.15 µF  C 0.39 µF 0.39 µF  C  0.56 µF 0.56 µF  C  0.82 µF 0.82 µF  C  1.2 µF 1.2 µF  C  1.8 µF 1.8 µF  C  2.2 µF 2.2 µF  C  2.7 µF Rated voltage pulse slope (dU/dt)R: C  0.15 µF 0.15 µF  C 0.39 µF 0.39 µF  C  0.82 µF 0.82 µF  C  2 µF 2 µF  C  2.7 µF R between leads, for C  1 µF at 100 V, 1 min RC between leads, for C 1 µF at 100 V, 1 min R between leads and case, 100 V, 1 min Ionization (AC) voltage (typical value) at 50 pC peak discharge Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s Withstanding (DC) voltage between leads and case Maximum application temperature www.vishay.com 188 VALUE at 10 kHz 5 x 10-4 5 x 10-4 10 x 10-4 10 x 10-4 10 x 10-4 10 x 10-4 15 x 10-4 15 x 10-4 For technical questions, contact: dc-film@vishay.com at 100 kHz  20 x 10-4  25 x 10-4 25 x 10-4  40 x 10-4 50 x 10-4 65 x 10-4 75 x 10-4  85 x 10-4 450 V/µs 900 V/µs 290 V/µs 190 V/µs 130 V/µs 100 000 M 100 000 s 30 000 M 220 V 400 V, 1 min 2840 V, 1 min 105 °C Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Vishay BCcomponents URdc = 250 V; URac = 125 V; Upp = 350 V; C-tol. = ± 5 % C (µF) DIMENSIONS w x h (h’) x l (mm) MASS (g) (1) CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL Pitch = 7.5 mm (bent back) Leads Leads Original pitch 3.5 ± 0.3 mm 25.0 ± 2.0 mm Ø 500 mm Ø 356 mm XX (SPQ) Pitch = 15 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm 0.082 00… 5.0 x 11.0 (13.0) x 17.5 1.1 0.091 (1250) 0.1 0.11 00… 0.12 6.0 x 12.0 (14.0) x 17.5 1.4 (1000) 0.13 0.15 0.16 00… 7.0 x 13.5 (15.5) x 17.5 1.8 0.18 (750) 0.2 0.22 00… 0.24 8.5 x 15.0 (17.0) x 17.5 2.6 (750) 0.27 0.3 0.33 00… 10.0 x 16.5 (18.5) x 17.5 3.3 0.36 (500) 0.39 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity XX (SPQ) XX (SPQ) Pitch = 15 mm C-VALUE ..YYY XX XX (SPQ) (SPQ) Pitch = 7.5 mm (bent back) 04… (1000) 02… (1100) 03… (950) 05… (550) 04… (1000) 02… (900) 03… (800) 05… (450) 04… (500) 02… (800) 03… (700) 05… (400) 04… (500) 02… (650) 03… (550) 05… (300) 04… (450) 02… (600) 03… (500) 05… (250) 823 913 104 114 124 134 154 164 184 204 224 244 274 304 334 364 394 URdc = 250 V; URac = 125 V; Upp = 350 V; C-tol. = ± 5 % CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL C-VALUE DIMENSIONS C MASS Leads Leads wxhxl Original pitch ..YYY (µF) (g) (1) 3.5 ± 0.3 mm 25.0 ± 2.0 mm (mm) XX XX XX (SPQ) (SPQ) (SPQ) Pitch = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch = 22.5 mm 00… 04… 02… 0.43 7.0 x 116.5 x 26.0 3.0 434 (200) (250) (550) 0.47 00… 0.51 8.5 x 18.0 x 26.0 4.2 (200) 0.56 0.62 0.68 00… 10.0 x 19.5 x 26.0 5.3 0.75 (200) 0.82 Pitch = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm 0.91 00… 1.0 11.0 x 21.0 x 31.0 8.0 (750) 1.1 1.2 1.3 00… 13.0 x 23.0 x 31.0 9.7 1.5 (500) 1.6 1.8 00… 15.0 x 25.0 x 31.0 12.6 (100) 2.0 2.2 00… 16.3 2.4 18.0 x 28.0 x 31.0 (100) 2.7 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity Document Number: 28124 Revision: 08-Aug-2018 04… (250) 02… (450) 04… (200) 02… (350) 474 514 564 624 684 754 824 Pitch = 27.5 mm 04… (125) 04… (125) 04… (125) 04… (100) For technical questions, contact: dc-film@vishay.com - 914 105 115 125 135 155 165 185 205 225 245 275 www.vishay.com 189 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type SPECIFIC REFERENCE DATA (400 Vdc) DESCRIPTION Tangent of loss angle: C  0.22 µF 0.22 µF  C  0.33 µF 0.33 µF  C  0.43 µF 0.43 µF  C  0.68 µF 0.68 µF  C  0.82 µF 0.82 µF  C  1.2 µF 1.2 µF  C  1.5 µF Rated voltage pulse slope (dU/dt)R: C  0.082 µF 0.082 µF  C 0.22 µF 0.22 µF  C  0.43 µF 0.42 µF  C  1.1 µF 1.1 µF  C  1.5 µF R between leads, for C  1 µF at 100 V, 1 min RC between leads, for C 1 µF at 100 V, 1 min R between leads and case, 100 V, 1 min Ionization (AC) voltage (typical value) at 50 pC peak discharge Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s Withstanding (DC) voltage between leads and case Maximum aplication temperature VALUE at 10 kHz 5 x 10-4  10 x 10-4  10 x 10-4  10 x 10-4  10 x 10-4  10 x 10-4 10 x 10-4 at 100 kHz 20 x 10-4 35 x 10-4  40 x 10-4 50 x 10-4 55 x 10-4  60 x 104  65 x 10-4 600 V/µs 1200 V/µs 410 V/µs 260 V/µs 180 V/µs 100 000 M 100 000 s 30 000 M  220 V 560 V, 1 min 2 840 V, 1 min 105 °C URdc = 400 V; URac = 200 V; Upp = 560 V; C-tol. = ± 5 % CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL C-VALUE DIMENSIONS C MASS Pitch = 7.5 mm (bent back) Leads Leads w x h (h’) x l (µF) (g) (1) 3.5 ± 0.3 mm 25.0 ± 2.0 mm Original pitch Ø 500 mm Ø 356 mm (mm) ..YYY XX XX XX XX XX (SPQ) (SPQ) (SPQ) (SPQ) (SPQ) Pitch = 15 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch = 15 mm Pitch = 7.5 mm (bent back) 0.047 5.0 x 11.0 (13.0) x 17.5 1.1 0.051 0.056 0.062 0.068 6.0 x 12.0 (14.0) x 17.5 1.4 0.075 0.082 0.091 7.0 x 13.5 (15.5) x 17.5 1.8 0.1 0.11 0.12 0.13 8.5 x 15.0 (17.0) x 17.5 2.5 0.15 0.16 0.18 10.0 x 16.5 (18.5) x 17.5 3.3 0.2 0.22 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity www.vishay.com 190 10… (1250) 14… (1000) 12… (1100) 13… (950) 15… (550) 10… (1000) 14… (1000) 12… (900) 13… (800) 15… (450) 10… (750) 14… (500) 12… (800) 13… (700) 15… (400) 10… (750) 14… (500) 12… (650) 13… (550) 15… (300) 10… (500) 14… (450) 12… (600) 13… (500) 15… (250) For technical questions, contact: dc-film@vishay.com 473 513 563 623 683 753 823 913 104 114 124 134 154 164 184 204 224 Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Vishay BCcomponents URdc = 400 V; URac = 200 ; Up-p = 560 V; C-tol. = ± 5 % C (µF) DIMENSIONS wxhxl (mm) MASS (g) (1) CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL C-VALUE Leads Leads Original pitch ..YYY 3.5 ± 0.3 mm 25.0 ± 2.0 mm XX (SPQ) XX (SPQ) 10… (200) 14… (250) XX (SPQ) Pitch = 22.5 mm 12… (550) 10… (200) 14… (250) 12… (450) 10… (200) 14… (200) 12… (350) Pitch = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm 0.24 7.0 x 116.5 x 26.0 3.0 0.27 8.5 x 18.0 x 26.0 4.2 0.30 0.33 0.36 10.0 x 19.5 x 26.0 5.3 0.39 0.43 Pitch = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm 0.47 0.51 11.0 x 21.0 x 31.0 8.0 0.56 0.62 0.68 13.0 x 23.0 x 31.0 9.7 0.75 0.82 0.91 15.0 x 25.0 x 31.0 12.6 1. 1.1 1.2 18.0 x 28.0 x 31.0 1.3 16.3 1.5 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity 244 274 304 334 364 394 434 Pitch = 27.5 mm 10… (100) 14… (125) 10… (100) 14… (125) 10… (100) 14… (125) 10… (100) 14… (100) - - 474 514 564 624 684 754 824 914 105 115 125 135 155 SPECIFIC REFERENCE DATA (630 Vdc) DESCRIPTION Tangent of loss angle: C  0.15 µF 0.15 µF  C  0.22 µF 0.22 µF  C  0.3 µF 0.3 µF  C  0.47 µF 0.47 µF  C  0.68 µF 0.68 µF  C  1.0 µF Rated voltage pulse slope (dU/dt)R: C  0.056 µF 0.056 µF  C 0.15 µF 0.15 µF  C  0.3 µF 0.3 µF  C  0.75 µF 0.75 µF  C  1.0 µF R between leads, for C  1 µF at 100 V, 1 min R between leads and case, 100 V, 1 min Ionization (AC) voltage (typical value) at 50 pC peak discharge Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s Withstanding (DC) voltage between leads and case Maximum application temperature Document Number: 28124 Revision: 08-Aug-2018 VALUE at 10 kHz 5 x 10-4  8 x 10-4  8 x 10-4  10 x 10-4  10 x 10-4  10 x 10-4 For technical questions, contact: dc-film@vishay.com at 100 kHz 15 x 10-4 25 x 10-4  30 x 10-4 40 x 10-4 45 x 10-4 50 x 10-4 700 V/µs 1400 V/µs 470 V/µs 300 V/µs 210 V/µs 100 000 M 30 000 M  250 V 1000 V, 1 min 2 840 V, 1 min 105 °C www.vishay.com 191 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type URdc = 630 V; URac = 220 V; Up-p = 630 V; C-tol. = ± 5 % CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL C-VALUE DIMENSIONS C MASS Pitch = 7.5 mm (bent back) Leads Leads w x h (h’) x l Original pitch (µF) (g) (1) 3.5 ± 0.3 mm 25.0 ± 2.0 mm Ø 500 mm Ø 356 mm (mm) ..YYY XX XX XX XX XX (SPQ) (SPQ) (SPQ) (SPQ) (SPQ) Pitch = 15 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch = 15 mm Pitch = 7.5 mm (bent back) 0.03 303 20… 24… 22… 23… 25… 5.0 x 11.0 (13.0) x 17.5 1.1 0.033 333 (1250) (1000) (2200) (950) (550) 0.036 363 0.039 393 0.043 433 20… 24… 22… 23… 25… 6.0 x 12.0 (14.0) x 17.5 1.4 0.047 473 (1000) (1000) (900) (800) (450) 0.051 513 0.056 563 0.062 623 20… 24… 22… 23… 25… 7.0 x 13.5 (15.5) x 17.5 1.8 0.068 683 (750) (500) (800) (700) (400) 0.075 753 0.082 823 0.091 913 20… 24… 22… 23… 25… 8.5 x 15.0 (17.0) x 17.5 2.5 (750) (500) (650) (550) (300) 0.1 104 0.11 114 0.12 124 20… 24… 22… 23… 25… 10.0 x 16.5 (18.5) x 17.5 3.3 0.13 134 (500) (450) (600) (500) (250) 0.15 154 Pitch = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch = 22.5 mm 0.16 164 0.18 184 20… 24… 22… 8.5 x 18.0 x 26.0 4.2 (200) (250) (450) 0.2 204 0.22 224 0.24 174 20… 24… 22… 10.0 x 19.5 x 26.0 5.3 0.27 304 (200) (200) (350) 0.3 Pitch = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch = 27.5 mm 0.33 334 0.36 364 20… 24… 11.0 x 21.0 x 31.0 8.0 (750) (125) 0.39 394 0.43 434 0.47 474 20… 24… 13.0 x 23.0 x 31.0 9.7 0.51 514 (500) (125) 0.56 564 0.62 20… 24… 624 (100) (125) 15.0 x 25.0 x 31.0 12.6 0.68 684 0.75 754 0.82 824 20… 24… 18.0 x 28.0 x 31.0 16.3 0.91 914 (100) (100) 1.0 105 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity www.vishay.com 192 For technical questions, contact: dc-film@vishay.com Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Vishay BCcomponents SPECIFIC REFERENCE DATA (1000 Vdc) DESCRIPTION Tangent of loss angle: C  0.062 µF 0.062 µF  C  0.13 µF 0.13 µF  C  0.22 µF 0.22 µF  C  0.33 µF 0.33 µF  C  0.47 µF Rated voltage pulse slope (dU/dt)R: C  0.024 µF 0.024 µF  C 0.062 µF 0.062 µF  C  0.13 µF 0.13 µF  C  0.33 µF 0.33 µF  C  0.47 µF R between leads, for C  1 µF at 500 V, 1 min R between leads and case, 500 V, 1 min Ionization (AC) voltage (typical value) at 50 pC peak discharge Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s Withstanding (DC) voltage between leads and case Maximum application temperature VALUE at 10 kHz 5 x 10-4  6 x 10-4  8 x 10-4  8 x 10-4  8 x 10-4 at 100 kHz 15 x 10-4 20 x 10-4  25 x 10-4 30 x 10-4 35 x 10-4 1700 V/µs 3300 V/µs 1200 V/µs 700 V/µs 470 V/µs 100 000 M 30 000 M  440 V 1600 V, 1 min 2840 V, 1 min 105 °C URdc = 1000 V; URac = 350 V; Up-p = 1000 V; C-tol. = ± 5 % CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL C-VALUE DIMENSIONS C MASS Pitch = 7.5 mm (bent back) Leads Leads w x h (h’) x l (µF) (g) (1) 3.5 ± 0.3 mm 25.0 ± 2.0 mm Original pitch Ø 500 mm Ø 356 mm (mm) ..YYY XX XX XX XX XX (SPQ) (SPQ) (SPQ) (SPQ) (SPQ) Pitch = 15 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch = 15 mm Pitch = 7.5 mm (bent back) 0.0043 0.0047 0.0051 0.0056 0.0062 0.0068 0.0075 5.0 x 11.0 (13.0) x 17.5 0.0082 0.0091 0.01 0.011 0.012 0.013 0.015 0.016 0.018 0.02 6.0 x 12.0 (14.0) x 17.5 0.022 0.024 0.027 7.0 x 13.5 (15.5) x 17.5 0.030 0.033 0.036 0.039 8.5 x 15.0 (17.0) x 17.5 0.043 0.047 0.051 10.0 x 16.5 (18.5) x 17.5 0.056 0.062 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity Document Number: 28124 Revision: 08-Aug-2018 1.1 30… (1250) 34… (1000) 32… (1100) 33… (950) 35… (550) 1.4 30… (1000) 34… (1000) 32… (900) 33… (800) 35… (450) 1.8 30… (750) 34… (500) 32… (800) 33… (700) 35… (400) 2.5 30… (750) 34… (500) 32… (650) 33… (550) 35… (300) 3.3 30… (500) 34… (450) 32… (600) 33… (500) 35… (250) For technical questions, contact: dc-film@vishay.com 432 472 512 562 622 682 752 822 912 103 113 123 133 153 163 183 203 223 243 273 303 333 363 393 433 473 513 563 623 www.vishay.com 193 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL C MASS Leads Leads (1) Original pitch (µF) (g) XX XX XX (SPQ) (SPQ) (SPQ) Pitch = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch 22.5 mm 30 ... 34… 32… 0.068 7.0 x 16.5 x 26.5 3.0 (200) (250) (550) 0.075 30… 34… 32… 8.5 x 18.0 x 26.0 4.2 0.082 (200) (250) (450) 0.091 0.1 30… 34… 32… 0.11 10.0 x 19.5 x 26.0 5.3 (200) (200) (350) 0.12 0.13 Pitch = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch = 27.5 mm 0.15 30… 34… 11.0 x 21.0 x 31.0 8.0 0.16 (100) (125) 0.18 0.2 30… 34… 13.0 x 23.0 x 31.0 9.7 0.22 (100) (125) 0.24 0.27 30… 34… 15.0 x 25.0 x 31.0 12.6 0.3 (100) (125) 0.33 0.36 30… 34… 0.39 18.0 x 28.0 x 31.0 16.3 (100) (100) 0.43 0.47 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity DIMENSIONS w x h (h’) x l (mm) C-VALUE ..YYY 683 753 823 913 104 114 124 134 154 164 184 204 224 244 274 304 334 364 394 434 474 SPECIFIC REFERENCE DATA (1400 Vdc) DESCRIPTION Tangent of loss angle: C  0.016 µF 0.016 µF  C  0.039 µF 0.039 µF  C  0.13 µF Rated voltage pulse slope (dU/dt)R: C  0.0056 µF 0.0056 µF  C 0.016 µF 0.016 µF  C  0.039 µF 0.039 µF  C  0.1 µF 0.1 µF  C  0.13 µF R between leads, for C  1 µF at 500 V, 1 min R between leads and case, 500 V, 1 min Ionization (AC) voltage (typical value) at 20 pC peak discharge Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s Withstanding (DC) voltage between leads and case Maximum application temperature www.vishay.com 194 VALUE at 10 kHz 5 x 10-4  5 x 10-4  5 x 10-4 For technical questions, contact: dc-film@vishay.com at 100 kHz 10 x 10-4 15 x 10-4  20 x 10-4 8000 V/µs 15 000 V/µs 4000 V/µs 2100 V/µs 1500 V/µs 100 000 M 30 000 M  500 V 2250 V, 1 min 2840 V, 1 min 105 °C Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Vishay BCcomponents URdc = 1400 V; URac = 500 V; Up-p = 1400 V; C-tol. = ± 5 % CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL C-VALUE DIMENSIONS C MASS Pitch = 7.5 mm (bent back) Leads Leads w x h (h’) x l (µF) (g) (1) 3.5 ± 0.3 mm 25.0 ± 2.0 mm Original pitch Ø 500 mm Ø 356 mm (mm) ..YYY XX XX XX XX XX (SPQ) (SPQ) (SPQ) (SPQ) (SPQ) Pitch = 15 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch = 15 mm Pitch = 7.5 mm (bent back) 0.0022 222 0.0024 242 0.0027 272 40… 44… 42… 43… 45… 5.0 x 11.0 (13.0) x 17.5 0.003 1.1 302 (1250) (1000) (1100) (950) (550) 0.0033 332 0.0036 362 0.0039 392 0.0043 432 0.0047 40… 44… 42… 43… 45… 472 6.0 x 12.0 (14.0) x 17.5 1.4 (1000) (1000) (900) (800) (450) 0.0051 512 0.0056 562 0.0062 622 0.0068 40… 44… 42… 43… 45… 682 7.0 x 13.5 (15.5) x 17.5 1.8 (750) (500) (800) (700) (400) 0.0075 752 0.0082 822 0.0091 912 0.01 40… 44… 42… 43… 45… 103 8.5 x 15.0 (17.0) x 17.5 2.5 (750) (500) (650) (550) (300) 0.011 113 0.012 123 0.013 133 10.0 x 16.5 (18.5) x 40… 44… 42… 43… 45… 3.3 0.015 153 17.5 (500) (450) (600) (500) (250) 0.016 163 Pitch = 22.5 ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch = 22.5 mm 0.018 183 40… 44… 42… 7.0 x 16.5 x 26.0 3 (200) (250) (550) 0.02 203 0.022 223 40… 44… 42… 8.5 x 18.0 x 26.0 4.2 0.024 243 (200) (250) (450) 0.027 273 0.03 303 0.033 333 40… 44… 42… 10.0 x 19.5 x 26.0 5.3 (200) (200) (350) 0.036 363 0.039 393 Pitch = 27.5 ± 0.4 mm; dt = 0.80 mm ± 0.08 mm Pitch = 27.5 mm 0.043 433 0.047 40… 44… 473 11.0 x 21.0 x 31.0 8 0.051 513 0.056 563 0.062 623 40… 44… 13.0 x 23.0 x 31.0 9.7 0.068 683 (100) (125) 0.075 753 0.082 823 40… 44… 15.0 x 25.0 x 31.0 12.6 0.091 913 (100) (125) 0.1 104 0.11 114 40… 44… 18.0 x 28.0 x 31.0 16.3 0.12 124 (100) (100) 0.13 134 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity Document Number: 28124 Revision: 08-Aug-2018 For technical questions, contact: dc-film@vishay.com www.vishay.com 195 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type SPECIFIC REFERENCE DATA (1600 Vdc) DESCRIPTION Tangent of loss angle: C  0.015 µF 0.015 µF  C  0.15 µF Rated voltage pulse slope (dU/dt)R: C  0.0056 µF 0.0056 µF  C 0.0075 µF 0.0075 µF  C  0.039 µF 0.039 µF  C  0.1 µF 0.1 µF  C  0.15 µF R between leads, for C  1 µF at 500 V, 1 min R between leads and case, 500 V, 1 min Ionization (AC) voltage (typical value) at 20 pC peak discharge Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s Withstanding (DC) voltage between leads and case Maximum aplication temperature VALUE at 10 kHz 5 x 10-4  5 x 10-4 at 100 kHz 15 x 10-4 20 x 10-4 8000 V/µs 15 000 V/µs 3100 V/µs 1800 V/µs 1200 V/µs 100 000 M 30 000 M  660 V 2560 V, 1 min 2840 V, 1 min 105 °C URdc = 1600 V; URac = 550 V; Up-p = 1600 V; C-tol. = ± 5 % C (µF) DIMENSIONS w x h (h’) x l (mm) MASS (g) (1) CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL Leads Leads Pitch = 7.5 mm (bent back) Original pitch 3.5 ± 0.3 25.0 ± 2.0 Ø 500 mm Ø 356 mm XX (SPQ) Pitch = 15 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm 0.0027 0.003 50… 5.0 x 11.0 (13.0) x 17.5 1.1 0.0033 (1250) 0.0036 0.0039 0.0043 50… 0.0047 6.0 x 12.0 (14.0) x 17.5 1.4 (1000) 0.0051 0.0056 0.0062 7.0 x 13.5 (15.5) x 17.5 1.8 0.0068 0.0075 0.0082 0.0091 8.5 x 15.0 (17.0) x 17.5 2.5 0.01 0.011 0.012 10.0 x 16.5 (18.5) x 17.5 3.3 0.013 0.015 Pitch = 22.5 ± 0.4 mm; dt = 0.80 mm ± 0.08 mm 0.016 7.0 x 16.5 x 26.0 3.0 0.018 0.02 0.022 0.024 8.5 x 18.0 x 26.0 4.2 0.027 0.03 0.033 10.0 x 19.5 x 26.0 5.3 0.036 0.039 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity www.vishay.com 196 XX (SPQ) XX (SPQ) Pitch = 15 mm XX XX (SPQ) (SPQ) Pitch = 7.5 mm (bent back) 54… (1000) 52… (1100) 53… (950) 55… (550) 54… (1000) 52… (900) 53… (800) 55… (450) 50… (750) 54… (500) 52… (800) 53… (700) 55… (400) 50… (750) 54… (500) 52… (650) 53… (550) 55… (300) 50… (500) 54… (450) 52… (600) 53… (500) 55… (250) C-VALUE ..YYY 272 302 332 362 392 432 472 512 562 622 682 752 822 912 103 113 123 133 153 Pitch = 22.5 mm 50… (200) 54… (250) 52… (550) - - 50… (200) 54… (250) 52… (450) - - 50… (200) 54… (200) 52… (350) - - For technical questions, contact: dc-film@vishay.com 163 183 203 223 243 273 303 333 363 393 Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Vishay BCcomponents URdc = 1600 V; URac = 550 V; Up-p = 1600 V; C-tol. = ± 5 % C (µF) DIMENSIONS w x h (h’) x l (mm) CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL Leads Leads Pitch = 7.5 mm (bent back) Original pitch 3.5 ± 0.3 25.0 ± 2.0 Ø 500 mm Ø 356 mm MASS (g) (1) XX (SPQ) XX (SPQ) Pitch = 27.5 ± 0.4 mm; dt= 0.80 mm ± 0.08 mm XX (SPQ) XX (SPQ) C-VALUE XX (SPQ) Pitch = 27.5 mm 0.043 0.047 0.051 433 11.0 x 21.0 x 31.0 50… (100) 8 473 54… (125) 513 0.056 563 0.062 0.068 623 13.0 x 23.0 x 31.0 50… (100) 9.7 54… (125) 683 0.075 753 - 0.082 0.091 ..YYY 15.0 x 25.0 x 31.0 50… (100) 12.6 823 54… (125) 913 0.1 104 0.11 114 0.12 0.13 18.0 x 28.0 x 31.0 50… (100) 16.3 124 54… (100) 134 0.15 154 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity SPECIFIC REFERENCE DATA (2000 Vdc) DESCRIPTION Tangent of loss angle: C  0.01 µF 0.01 µF  C  0.1 µF Rated voltage pulse slope (dU/dt)R: C  0.0036 µF 0.0036 µF  C 0.01 µF 0.01 µF  C  0.024 µF 0.024 µF  C  0.068 µF 0.068 µF  C  0.1 µF R between leads, for C  1 µF at 500 V, 1 min R between leads and case, 500 V, 1 min Ionization (AC) voltage (typical value) at 20 pC peak discharge Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s Withstanding (DC) voltage between leads and case Maximum application temperature Document Number: 28124 Revision: 08-Aug-2018 VALUE at 10 kHz 5 x 10-4  10 x 10-4 For technical questions, contact: dc-film@vishay.com at 100 kHz 15 x 10-4 18 x 10-4 11 000 V/µs 20 000 V/µs 4400 V/µs 2500 V/µs 1800 V/µs 100 000 M 30 000 M  750 V 3200 V, 1 min 2840 V, 1 min 105 °C www.vishay.com 197 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type URdc = 2000 V; URac = 700 V; Up-p = 2000 V; C-tol. = ± 5 % DIMENSIONS w x h (h’) x l (mm) C (µF) MASS (g) (1) CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL Leads Leads Pitch = 7.5 mm (bent back) Original pitch 3.5 ± 0.3 25.0 ± 2.0 Ø 500 mm Ø 356 mm XX (SPQ) Pitch = 15 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm XX (SPQ) XX (SPQ) Pitch = 15 mm XX XX (SPQ) (SPQ) Pitch = 7.5 mm (bent back) C-VALUE ..YYY 0.001 102 0.0011 112 0.0012 122 0.0013 132 0.0015 0.0016 5.0 x 11.0 (13.0) x 17.5 1.1 60… (1250) 64… (1000) 62… (1100) 63… (950) 65… (550) 152 162 0.0018 182 0.002 202 0.0022 222 0.0024 242 0.0027 0.003 0.0033 272 6.0 x 12.0 (14.0) x 17.5 1.4 60… (1000) 64… (1000) 62… (900) 63… (800) 65… (450) 0.0036 7.0 x 13.5 (15.5) x 17.5 1.8 0.0047 60… (750) 64… (500) 62… (800) 63… (700) 65… (400) 60… (750) 64… (500) 62… (650) 63… (550) 65… (300) 0.0051 0.0056 0.0062 332 362 0.0039 0.0043 302 392 432 472 512 8.5 x 15.0 (17.0) x 17.5 2.5 562 622 0.0068 682 0.0075 752 0.0082 0.0091 10.0 x 16.5 (18.5) x 17.5 3.3 60… (500) 64… (450) 62… (600) 63… (500) 65… (250) 0.01 0.011 7.0 x 16.5 x 26.0 3.0 0.013 0.015 0.016 8.5 x 18.0 x 26.0 4.2 0.018 0.02 0.022 10.0 x 19.5 x 26.0 5.3 0.024 Pitch = 22.5 mm 113 60… (200) 64… (250) 62… (550) - 60… (200) 64… (250) 62… (450) - 60… (200) 64… (200) 62… (350) - Pitch = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm - 123 133 153 - 163 183 203 - 223 243 Pitch = 27.5 mm 0.027 273 0.03 0.033 912 103 Pitch = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm 0.012 822 11.0 x 21.0 x 31.0 0.036 8.0 60… (100) 64… (125) 0.039 - 303 333 363 393 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity www.vishay.com 198 For technical questions, contact: dc-film@vishay.com Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type C (µF) DIMENSIONS w x h (h’) x l (mm) Vishay BCcomponents CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING LOOSE IN BOX REEL Leads Leads Pitch = 7.5 mm (bent back) Original pitch 3.5 ± 0.3 25.0 ± 2.0 Ø 500 mm Ø 356 mm MASS (g) (1) XX (SPQ) Pitch = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm XX (SPQ) XX (SPQ) Pitch = 27.5 mm XX (SPQ) C-VALUE XX (SPQ) 0.043 0.047 433 13.0 x 23.0 x 31.0 60… (100) 9.7 64… (125) 473 0.051 513 0.056 0.062 563 15.0 x 25.0 x 31.0 60… (100) 12.6 64… (125) 623 - 0.068 683 0.075 0.082 0.091 ..YYY 753 18.0 x 28.0 x 31.0 60… (100) 16.3 823 64… (100) 913 0.10 104 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity SPECIFIC REFERENCE DATA (2500 Vdc) DESCRIPTION VALUE Tangent of loss angle: at 10 kHz at 100 kHz C  0.015 µF 5 x 10-4 10 x 10-4 0.015 µF  C  0.056 µF 5x 15x 10-4 10-4 Rated voltage pulse slope (dU/dt)R: C  0.015 µF 13 000 V/µs 0.015 µF  C 0.043 µF 6000 V/µs 0.043 µF  C  0.056 µF 4200 V/µs R between leads, for C  1 µF at 500 V, 1 min 100 000 M R between leads and case, 500 V, 1 min 30 000 M Ionization (AC) voltage (typical value) at 20 pC peak discharge  1000 V Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s 3500 V, 1 min Withstanding (DC) voltage between leads and case 2840 V, 1 min Maximum application temperature Document Number: 28124 Revision: 08-Aug-2018 105 °C For technical questions, contact: dc-film@vishay.com www.vishay.com 199 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type URdc = 2500 V; URac = 900 V; Up=p = 2500 V; C-tol. = ± 5 % CATALOG NUMBER BFC2 383 XXYYY AND PACKAGING C (µF) DIMENSIONS wxhxl (mm) LOOSE IN BOX MASS (g) (1) Pitch = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm 0.001 0.0011 0.0012 0.0013 0.0015 0.0016 0.0018 0.002 0.0022 6.0 x 15.5 x 26.0 2.4 0.0024 0.0027 0.003 0.0033 0.0036 0.0039 0.0043 0.0047 0.0051 0.0056 0.0062 7.0 x 16.5 x 26.0 3.0 0.0068 0.0075 0.0082 0.0091 8.5 x 18.0 x 26.0 4.2 0.01 0.011 0.012 10.0 x 19.5 x 26.0 5.3 0.013 0.015 Pitch = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm 0.016 9.0 x 19.0 x 31.0 5.9 0.018 0.02 11.0 x 21.0 x 31.0 8.0 0.022 0.024 0.027 13.0 x 23.0 x 31.0 9.7 0.03 0.033 0.036 15.0 x 25.0 x 31.0 12.6 0.039 0.043 0.047 18.0 x 28.0 x 31.0 16.3 0.051 0.056 REEL C-VALUE Leads 3.5 ± 0.3 mm Leads 25.0 ± 2.0 mm H = 18.5 mm ..YYY XX (SPQ) XX (SPQ) XX (SPQ) 70… (200) 74… (250) 72… (600) 70… (200) 74… (250) 72… (550) 70… (200) 74… (250) 72… (450) 70… (200) 74… (200) 72… (350) 70… 74… 70… (100) 74… (125) 70… (100) 74… (125) 70… (100) 74… (125) 70… (100) 74… (100) - 102 112 122 132 152 162 182 202 222 242 272 302 332 362 392 432 472 512 562 622 682 752 822 912 103 113 123 133 153 163 183 203 223 243 273 303 333 363 393 433 473 513 563 Notes (1) Net weight for short lead products only • SPQ = Standard Packaging Quantity www.vishay.com 200 For technical questions, contact: dc-film@vishay.com Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Vishay BCcomponents MOUNTING Normal Use The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting on printed-circuit boards by means of automatic insertion machines. For detailed tape specifications refer to “Packaging Information” www.vishay.com/docs?28139 Specific Method of Mounting to Withstand Vibration and Shock In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the printed-circuit board:  For original pitch 15 mmthe capacitors shall be mechanically fixed by the leads  For larger pitches the capacitors shall be mounted in the same way and the body clamped  Space Requirements on Printed-Circuit Board The maximum length and width of film capacitors is shown in the drawing:  Eccentricity as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned  Product height with seating plane as given by “IEC 60717” as reference: hmax.  h + 0.3 mm bmax. = b + 0.3 mm Eccentricity Imax. = I + 0.3 mm Storage Temperature  Storage temperature: Tstg = - 25 °C to + 40 °C with RH maximum 80 % without condensation Ratings and Characteristics Reference Conditions Unless otherwise specified, all electrical values apply to an ambient free temperature of 23 °C ± 1 °C, an atmospheric pressure of 86 kPa to 106 kPa and a relative humidity of 50 % ± 2 %. For reference testing, a conditioning period shall be applied over 96 h ± 4 h by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. Document Number: 28124 Revision: 08-Aug-2018 For technical questions, contact: dc-film@vishay.com www.vishay.com 201 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type CHARACTERISTICS Capacitance as a function of ambient temperature (typical curve) (1 kHz) Impedance as a function of frequency (typical curve) 102 Impedance (Ω) 4 C/C (%) 1 kHz typical 2 101 max. 0 100 1.0 nF -2 10-1 -4 10-2 10 nF 100 nF 2.2 F min. -6 - 60 - 20 20 1.0 F 10-3 104 60 Tamb (°C) 100 105 106 107 f (Hz) 108 Max. DC and AC voltage as function of temperature factor 1.2 1.0 0.8 0.6 0.4 0.2 0.0 - 50 - 20 20 60 Tamb (°C) 100 103 103 AC voltage (V) Max. RMS voltage as a function of frequency AC voltage (V) Max. RMS voltage as a function of frequency 102 102 F 0n F 10 0 n F 22 0 n F 47 0 n F 0 n 10 00 22 F 0n F 1020 nnF 2 0 F 47 00 n nF 10 200 2 Tamb ≤ 85 °C, 250 Vdc 101 103 104 www.vishay.com 202 105 106 107 f (Hz) 108 101 102 85 °C ≤ Tamb 100 °C, 250 Vdc 103 For technical questions, contact: dc-film@vishay.com 104 105 106 f (Hz) 107 Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Max. RMS voltage as a function of frequency Max. RMS voltage as a function of frequency 10 103 AC voltage (V) AC voltage (V) 3 102 102 nF 47 0 nF F 10 0 n 22 0 nF F 47 0 n 0 10 nF 47 nF F 0 10 0 n F 22 0 n nF 47 00 10 101 103 Tamb ≤ 85 °C, 400 Vdc 104 85 °C < Tamb ≤ 100 °C, 400 Vdc 105 106 107 f (Hz) 108 101 102 Max. RMS voltage as a function of frequency 103 104 105 106 f (Hz) 107 Max. RMS voltage as a function of frequency AC voltage (V) 102 Tamb ≤ 85 °C, 630 Vdc 101 104 103 105 106 107 f (Hz) 108 101 102 Max. RMS voltage as a function of frequency nF 47 0 nFF 10 0 n F 22 0 n nF 47 00 10 102 nF 47 0 nFF 10 0 n F 22 0 n nF 47 00 10 10 AC voltage (V) 3 103 85 °C < Tamb ≤ 100 °C, 630 Vdc 103 104 105 106 f (Hz) 107 Max. RMS voltage as a function of frequency 103 AC voltage (V) AC voltage (V) 103 nF 4.7 nF 10 nF 22 7 nF F 4 n F 0 1020 nnF 2 70 4 102 Tamb ≤ 85 °C, 1000 Vdc 4 10 Document Number: 28124 Revision: 08-Aug-2018 5 10 6 10 7 10 8 f (Hz) 10 101 102 nF 4.7 nF 10 nF 22 nF F 4700 n nF 1 20 nF 2 70 4 102 101 103 Vishay BCcomponents 85 °C < Tamb ≤ 100 °C, 1000 Vdc 103 104 For technical questions, contact: dc-film@vishay.com 105 106 f (Hz) 107 www.vishay.com 203 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Max. RMS voltage as a function of frequency 103 AC voltage (V) AC voltage (V) 103 102 85 °C < Tamb ≤ 105 °C, 1400 Vdc Tamb ≤ 85 °C, 1400 Vdc 104 105 106 107 f (Hz) 108 101 102 Max. RMS voltage as a function of frequency 3 104 105 106 f (Hz) 107 AC voltage (V) AC voltage (V) 3 102 85 °C < Tamb ≤ 100 °C, 1600 Vdc Tamb ≤ 85 °C, 1600 Vdc 104 105 nF 4.70 nFnF 1 227 nFnF 4 0 10 nFF 4.70 n nF 1 227 nFnF 4 0 10 102 106 107 f (Hz) 108 101 102 Max. RMS voltage as a function of frequency 103 104 105 106 f (Hz) 107 Max. RMS voltage as a function of frequency 103 102 AC voltage (V) 102 Tamb ≤ 85 °C, 2000 Vdc 104 www.vishay.com 204 105 nF 1.0 nF 2.2.7 nFF 4 0 n nF 1 22 7 nF F 4 0n 10 nF F 1.0 n 2.27 nFF 4. 0 n nF 1 227 nF F 4 0n 10 AC voltage (V) 103 101 103 103 Max. RMS voltage as a function of frequency 10 10 101 103 nF 2.2.7 nF 4 0 nF F 1 n 227 nF F 4 0n 10 nF 2.2.7 nFF 4 0 n nF 1 227 nFnF 4 0 10 102 101 103 Max. RMS voltage as a function of frequency 106 107 f (Hz) 108 101 102 85 °C < Tamb ≤ 100 °C, 2000 Vdc 103 For technical questions, contact: dc-film@vishay.com 104 105 106 f (Hz) 107 Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Max. RMS voltage as a function of frequency Vishay BCcomponents Max. RMS voltage as a function of frequency 103 AC voltage (V) nF 1.0.2 nF 2 nF 4.7 nF 102 nFF 2 7n 4 102 102 85 °C < Tamb ≤ 105 °C, 2500 Vdc Tamb ≤ 85 °C, 2500 Vdc 101 103 104 105 nF 1.0 nF 2.2 nF 4.7 nF 10 nF 22 nF 47 AC voltage (V) 103 106 107 f (Hz) 108 101 102 104 105 106 f (Hz) 107 Max. allowed component temperature rise (T) as a function of the ambient temperature (Tamb) Insulation resistance as a function of ambient temperature 106 103 RC (s) ΔT (°C) 12 8 105 4 104 0 0 20 40 Document Number: 28124 Revision: 08-Aug-2018 60 80 100 Tamb (°C) - 50 - 20 For technical questions, contact: dc-film@vishay.com 20 60 Tamb (°C) 100 www.vishay.com 205 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Tangent of loss angle as a function of frequency (typical curve) Dissipation factor (x 10-4) 103 102 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 20 19 18 17 101 100 102 103 104 105 (Hz) 106 250 V C 0.091 µF, curve 8 C 0.015 µF, curve 9 C 0.022 µF, curve 10 C 0.027 µF, curve 11 C 0.033 µF, curve 12 C 0.056 µF, curve 15 C 0.082 µF, curve 16 C 1.2 µF, curve 18 C 1.61 µF, curve 19 C 2.21 µF, curve 20 400 V C 0.047 µF, curve 5 C 0.068 µF, curve 6 C 0.1 µF, curve 7 C 0.2 µF, curve8 C 0.24 µF, curve 12 C 0.36 µF, curve 13 C 0.43 µF, curve 14 C 56 µF, curve 16 C 1.1 µF, curve 17 630 V C 0.033 µF, curve 4 C 0.068 µF, curve 5 C 0.1 µF, curve 6 C 0.15 µF, curve 7 C 0.22 µF, curve 11 C 0.27 µF, curve 12 C 0.47 µF, curve 15 C 0.68 µF, curve 16 1000 V C 0.01 µF, curve 2 C 0.027 µF, curve 3 C 0.047 µF, curve 4 C 0.062 µF, curve 5 C 0.075 µF, curve 6 C 0.1 µF, curve 7 C 0.15 µF, curve 8 C 0.22 µF, curve 9 C 0.3 µF, curve 10 C 0.39 µF, curve 11 C 0.47 µF, curve 12 140 V C 0.0047 µF, curve 1 C 0.016 µF, curve 2 C 0.033 µF, curve 3 C 0.051 µF, curve 4 C 0.068 µF, curve 5 C 0.082 µF, curve 6 C 0.1 µF, curve 7 1600 V C 0.0047 µF, curve 3 C 0.0091 µF, curve 4 C 0.068 µF, curve 5 C 0.01 µF, curve 6 C 0.15 µF, curve 7 2000 V C 0.0047 µF, curve 2 C 0.033 µF, curve 3 C 0.1 µF, curve 4 2500 V C 0.0047 µF, curve 1 C 0.015 µF, curve 2 C 0.056 µF, curve 3 HEAT CONDUCTIVITY (G) AS A FUNCTION OF (ORIGINAL) PITCH AND CAPACITOR BODY THICKNESS IN mW/°C HEAT CONDUCTIVITY (mW/°C) Wmax. (mm) PITCH 15 mm PITCH 22.5 mm PITCH 27.5 mm 4.0 5.0 6.0 7.0 8.5 10.0 11.0 13.0 15.0 18.0 10 11 12 16 18 - 19 21 25 28 - 36 42 48 57 www.vishay.com 206 For technical questions, contact: dc-film@vishay.com Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Vishay BCcomponents POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of the free air ambient temperature. The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film Capacitors”. The component temperature rise (T) can be measured (see section “Measuring the component temperature” for more details) or calculated by T = P/G:  T = Component temperature rise (°C)  P = Power dissipation of the component (mW)  G = Heat conductivity of the component (mW/°C) MEASURING THE COMPONENT TEMPERATURE A thermocouple must be attached to the capacitor body as in: Thermocouple The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC). The temperature rise is given by T = TC - Tamb. To avoid radiation or convection, the capacitor should be tested in a wind-free box. APPLICATION NOTE AND LIMITING CONDITIONS These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference suppression capacitors conforming the standards must be used. To select the capacitor for a certain application, the following conditions must be checked: 1. The peak voltage (UP) shall not be greater than the rated DC voltage (URdc) 2. The peak-to-peak voltage (UP-P) shall not be greater than 22 x URac to avoid the ionisation inception level 3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URdc and divided by the applied voltage. For all other pulses following equation must be fulfilled: T 2 dU dU 2    --------  dt  U Rdc   --------  dt  rated  dt  0 T is the pulse duration. 4. The maximum component surface temperature rise must be lower than the limits (see graph max. allowed component temperature rise). 5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values mentioned in the table: “Heat Conductivity” Document Number: 28124 Revision: 08-Aug-2018 For technical questions, contact: dc-film@vishay.com www.vishay.com 207 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type 6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and surge voltages from the mains included). Voltage Conditions for 6 Above ALLOWED VOLTAGES Maximum continuous RMS voltage Maximum temperature RMS-overvoltage (< 24 h) Maximum peak voltage (VO-P) (< 2 s) Tamb  85 °C 85 °C < Tamb  105 °C URac URac 1.25 x URac 1.6 x URdc 1.25 x URac 1.1 x URdc EXAMPLE C = 4 nF - 1600 V used for the voltage signal shown in next drawing. UP-P = 1000 V; UP = 900 V; T1 = 12 µs; T2 = 64 µs; T3 = 4 µs The ambient temperature is 80 °C. In case of failure, the oscillation is blocked. Checking conditions: 1. The peak voltage UP = 900 V is lower than 1600 Vdc 2. The peak-to-peak voltage 1000 V is lower than 22 x 550 Vac = 1600 UP-P 3. The voltage pulse slope (dU/dt) = 1000 V/4 µs = 250 V/µs This is lower than 8000 V/µs (see specific reference data for each version) 4. The dissipated power is 35 mW as calculated with fourier terms and typical tgd. The temperature rise for Wmax. = 6.0 mm and pitch = 15 mm will be 35 mW/11 mW/°C = 3.2 °C This is lower than 10 °C temperature rise at 80 °C, according graph. 5. Oscillation is blocked 6. Not applicable Voltage Signal Voltage Up Up-p Time T3 T1 T2 www.vishay.com 208 For technical questions, contact: dc-film@vishay.com Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type Vishay BCcomponents INSPECTION REQUIREMENTS General Notes: Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-17 and Specific Reference Data”. Group C Inspection Requirements SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.1 Dimensions (detail) As specified in chapters “General Data” of this specification 4.3.1 Initial measurements Capacitance Tangent of loss angle: For C  1 µF at 100 kHz or for C > 1 µF at 10 kHz 4.3 Robustness of terminations Tensile: Load 10 N; 10 s Bending: Load 5 N; 4 x 90° 4.4 Resistance to soldering heat Method: 1A Solder bath: 280 °C ± 5 °C Duration: 10 s 4.14 Component solvent resistance Isopropylalcohol at room temperature Method: 2 Immersion time: 5 min ± 0.5 min Recovery time: Min. 1 h, max. 2 h 4.4.2 Final measurements Visual examination No visible damage Legible marking Capacitance C/C|  1 % of the value measured initially Tangent of loss angle Increase of tan    0.0005 for: C  100 nF or  0.001 for: 100 nF < C  470 nF or  0.0015 for: C  470 nF Compared to values measured in 4.3.1 No visible damage SUB-GROUP C1B OTHER PART OF SAMPLE OF SUB-GROUP C1 4.6.1 Initial measurements Capacitance Tangent of loss angle: For C  1 µF at 100 kHz or for C > 1 µF at 10 kHz 4.15 Solvent resistance of the marking Isopropylalcohol at room temperature  Method: 1 Rubbing material: cotton wool 4.6 Rapid change of temperature 4.7 Vibration Immersion time: 5.0 min ± 0.5 min A = - 55 °C B = + 105 °C 5 cycles Duration t = 30 min Visual examination Mounting: see section “Mounting” for more information Procedure B4 Frequency range: 10 Hz to 55 Hz Amplitude: 0.75 mm or Acceleration 98 m/s² (whichever is less severe) Total duration 6 h Document Number: 28124 Revision: 08-Aug-2018 No visible damage Legible marking No visible damage For technical questions, contact: dc-film@vishay.com www.vishay.com 209 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 Vishay BCcomponents AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type SUB-CLAUSE NUMBER AND TEST SUB-GROUP C1B OTHER PART OF SAMPLE OF SUB-GROUP C1 4.7.2 Final inspection 4.9 Shock 4.9.3 Final measurements CONDITIONS PERFORMANCE REQUIREMENTS Visual examination Mounting:  See section “Mounting” for more information Pulse shape: Half sine Acceleration: 490 m/s² Duration of pulse: 11 ms Visual examination Capacitance Tangent of loss angle No visible damage Insulation resistance SUB-GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB-GROUPS  C1A AND C1B 4.10 Climatic sequence 4.10.2 Dry heat 4.10.3 4.10.4 Damp heat cyclic Test Db, first cycle Cold Damp heat cyclic Test Db, remaining cycles 4.10.6.2 Final measurements No visible damage C/C|  1 % of the value measured in 4.6.1 Increase of tan    0.0005 for: C  100 nF or  0.001 for: 100 nF < C  470 nF or  0.0015 for: C  470 nF Compared to values measured in 4.6.1 As specified in section “Insulation Resistance” of this specification Temperature: + 105 °C Duration: 16 h Temperature: - 55 °C Duration: 2 h 4.10.6 Voltage proof = URdc for 1 min within 15 min after removal from testchamber Visual examination Capacitance Tangent of loss angle Insulation resistance No breakdown of flash-over No visible damage Legible marking For original pitch = 22.5 mm and 27.5 mm: C/C|  3 % of the value measured in  4.4.2 or 4.9.3 Increase of tan    0.0005 for: C  100 nF or  0.001 for: 100 nF < C  470 nF or  0.0015 for: C  470 nF Compared to values measured in 4.3.1 or 4.6.1  50 % of values specified in section “Insulation Resistance” of this specification SUB-GROUP C2 4.11 Damp heat steady state 4.11.1 Initial measurements 4.11.3 Final measurements 56 days, 40 °C, 90 % to 95 % RH  no load Capacitance Tangent of loss angle at 1 kHz Voltage proof = URdc for 1 min within 15 min after removal from testchamber Visual examination Capacitance Tangent of loss angle Insulation resistance www.vishay.com 210 For technical questions, contact: dc-film@vishay.com No breakdown of flash-over No visible damage Legible marking |C/C|  1 % of the value measured in 4.11.1. Increase of tan    0.0005 for: C  100 nF or  0.001 for: 100 nF < C  470 nF or  0.0015 for: C  470 nF Compared to values measured in 4.11.1  50 % of values specified in section “Insulation Resistance” of this specification Document Number: 28124 Revision: 08-Aug-2018 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not for New Designs - Alternative Device: New MMKP383 MMKP383 AC and Pulse Double Metallized Polypropylene Film Capacitors MMKP Radial Potted Type SUB-CLAUSE NUMBER AND TEST CONDITIONS Vishay BCcomponents PERFORMANCE REQUIREMENTS SUB-GROUP C3A 4.12.1 Endurance test at 50 Hz alternating voltage Duration: 2000 h 1.25 x URdc at 105 °C 4.12.1.1 Initial measurements Capacitance Tangent of loss angle: For C  1 µF at 100 kHz or for C > 1 µF at 10 kHz 4.12.1.3 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C|  5 % compared to values measured in 4.12.1.1 Tangent of loss angle Increase of tan    0.0005 for: C  100 nF or  0.001 for: 100 nF < C  470 nF or  0.0015 for: C  470 nF Compared to values measured in 4.12.1.1 Insulation resistance  50 % of values specified in section “Insulation Resistance” of this specification  For - 55 °C to + 20 °C: + 1 % |C/C|  3.75 % or  for 20 °C to 105 °C: - 6 % |C/C|  0 %  As specified in section “Capacitance” of this specification. As specified in section “Insulation Resistance” of this specification SUB-GROUP C4 4.2.6 Temperature charcteristics Initial measurements Intermediate measurements  Final measurements Capacitance  Capacitance at - 55 °C Capacitance at 20 °C Capacitance at + 105 °C Capacitance  Insulation resistance 4.13 Charge and discharge 10 000 cycles Charged to URdc Discharge resistance: U Rdc R = -------------------------------------------------------------5 x C x  2.5 x dU  dt  4.13.1 Initial measurements Capacitance Tangent of loss angle: For C  1 µF at 100 kHz or for C > 1 µF at 10 kHz 4.13.3 Final measurements Capacitance |C/C|  1 % compared to values measured in 4.13.1 Tangent of loss angle Increase of tan    0.0005 for: C  100 nF or  0.001 for: 100 nF < C  470 nF or  0.0015 for: C  470 nF Compared to values measured in 4.13.1 Insulation resistance  50 % of values specified in section “Insulation Resistance” of this specification Document Number: 28124 Revision: 08-Aug-2018 For technical questions, contact: dc-film@vishay.com www.vishay.com 211 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000