IL300-X009

IL300 www.vishay.com Vishay Semiconductors Linear Optocoupler, High Gain Stability, Wide Bandwidth FEATURES • Couples AC and DC signals 8 NC C 1 A 2 K1 • High gain stability, ± 0.005 %/°C typically 7 NC K2 C 3 6 C A 4 5 A • Low input-output capacitance • Isolation rated voltage 4420 VRMS • Internal insulation distance, > 0.4 mm • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 V D E LINKS TO ADDITIONAL RESOURCES APPLICATIONS 3D 3D • Power supply feedback voltage / current 3D Models Related Documents • Medical sensor isolation Models • Audio signal interfacing DESCRIPTION • Isolated process control transducers The IL300 linear optocoupler consists of an AlGaAs infrared emitter irradiating an output PIN photodiode and a feedback photodiode. The feedback photodiode captures a percentage of the emitter’s flux and generates a control signal (IP1) that can be used to keep the emitter output constant by adjusting the emitter forward current. This compensates for the emitter’s non-linear, time, and temperature characteristics. The output PIN photodiode produces an output signal (IP2) that is linearly related to the servo optical flux created by the emitter. • Digital telephone isolation AGENCY APPROVALS • UL / cUL 1577 • DIN EN 60747-5-5 (VDE 0884-5), available with option 1 • BSI • FIMKO • CQC The time and temperature stability of the input-output coupler gain (K3) is insured by using matched PIN photodiodes that accurately track the output flux of the emitter. ORDERING INFORMATION I L 3 0 0 - D PART NUMBER E F G - K3 BIN X 0 # # PACKAGE OPTION DIP-8 Option 6 7.62 mm 10.55 mm T TAPE AND REEL Option 7 > 0.7 mm AGENCY CERTIFIED / PACKAGE UL, cUL, BSI, FIMKO, CQC Option 9 > 0.18 mm K3 BIN 0.557 to 1.618 0.765 to 1.181 0.851 to 1.061 0.851 to 0.955 0.945 to 1.061 IL300 IL300-DEFG IL300-EF IL300-E IL300-F - IL300-DEFG-X006 - IL300-E-X006 - SMD-8, option 7 IL300-X007T(1) IL300-DEFG-X007T(1) IL300-EF-X007T(1) IL300-E-X007T IL300-F-X007T(1) SMD-8, option 9 IL300-X009T IL300-DEFG-X009T IL300-EF-X009T IL300-E-X009T IL300-F-X009T(1) 0.557 to 1.618 0.765 to 1.181 0.851 to 1.061 0.851 to 0.955 0.945 to 1.061 IL300-F-X001 DIP-8 DIP-8, 400 mil, option 6 UL, cUL, BSI, FIMKO, CQC, VDE (option 1) DIP-8 - IL300-DEFG-X001 - - DIP-8, 400 mil, option 6 IL300-X016 IL300-DEFG-X016 IL300-EF-X016 - IL300-F-X016 SMD-8, option 7 IL300-X017 IL300-DEFG-X017T(1) IL300-EF-X017T(1) - IL300-F-X017T Note (1) Also available in tubes, do not put “T” on the end Rev. 2.4, 16-May-2022 Document Number: 83622 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IL300 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Power dissipation Pdiss 100 mW Forward current IF 60 mA Surge current (pulse width < 10 μs) IPK 250 mA Reverse voltage VR 5 V Junction temperature Tj 125 °C OUTPUT Power dissipation Pdiss 50 mW Reverse voltage VR 50 V Junction temperature Tj 125 °C Ptot 150 mW Storage temperature Tstg -55 to +150 °C Operating temperature Tamb -55 to +100 °C COUPLER Total package dissipation at 25 °C Note • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Forward voltage IF = 10 mA VF - 1.4 1.5 V Reverse current VR = 5 V IR - 1 - μA VF = 0 V, f = 1 MHz Cj - 26 - pF Vdet = -15 V, IF = 0 A ID - 1 25 nA INPUT (LED EMITTER) Junction capacitance OUTPUT Dark current Open circuit voltage IF = 10 mA VD - 500 - mV Short circuit current IF = 10 mA ISC - 90 - μA VF = 0 V, f = 1 MHz Cj - 12 - pF - 1 - pF 0.005 0.009 0.015 Junction capacitance COUPLER Input-output capacitance K1, servo gain (IP1/IF) VF = 0 V, f = 1 MHz IF = 10 mA, Vdet = -15 V K1 photocurrent (1)(2) IF = 10 mA, Vdet = -15 V IP1 - 90 - K2, forward gain (IP2/IF) IF = 10 mA, Vdet = -15 V K2 0.005 0.009 0.015 Servo μA Forward current IF = 10 mA, Vdet = -15 V IP2 - 90 - μA K3, transfer gain (K2/K1) (1)(2) IF = 10 mA, Vdet = -15 V K3 0.56 1 1.65 K2/K1 Transfer gain stability IF = 10 mA, Vdet = -15 V, Tamb = 0 °C to 75 °C ΔK3/ΔTA - ± 0.005 ± 0.15 %/°C Transfer gain linearity IF = 2 mA to 10 mA ΔK3 - ± 0.25 - % Rev. 2.4, 16-May-2022 Document Number: 83622 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IL300 www.vishay.com Vishay Semiconductors ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT IF = 10 mA, MOD = ± 4 mA, RL = 50 Ω BW (-3 db) - 1.4 - MHz - -45 - ° PHOTOCONDUCTIVE OPERATION Frequency response Phase response at 200 kHz Vdet = -15 V Notes • Minimum and maximum values were tested requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements (1) Bin sorting: K3 (transfer gain) is sorted into bins that are ± 6 %, as follows: Bin D = 0.765 to 0.859 Bin E = 0.851 to 0.955 Bin F = 0.945 to 1.061 Bin G = 1.051 to 1.181 K3 = K2/K1. K3 is tested at IF = 10 mA, Vdet = -15 V (2) Bin categories: All IL300s are sorted into a K3 bin, indicated by an alpha character that is marked on the part. The bins range from “A” through “J”. The IL300 is shipped in tubes of 50 each. Each tube contains only one category of K3. The category of the parts in the tube is marked on the tube label as well as on each individual part (3) Category options: standard IL300 orders will be shipped from the categories that are available at the time of the order. Any of the ten categories may be shipped. For customers requiring a narrower selection of bins, the bins can be grouped together as follows: IL300-DEFG: order this part number to receive categories D, E, F, G only IL300-EF: order this part number to receive categories E, F only IL300-E: order this part number to receive category E only SWITCHING CHARACTERISTICS PARAMETER Rise time Fall time TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT IF = 10 mA, MOD = +2 mA, RL = 10 kΩ tr - 0.8 - μs tf - 0.8 - μs IF = 12 mA Input IF = 10 mA IF VDET VDET VOUT 90 % VOUT Output 10 % tr Fig. 1 - Test Circuit tf Fig. 2 - Switching Times COMMON MODE TRANSIENT IMMUNITY PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Common mode capacitance VF = 0 V, f = 1 MHz CCM - 1 - pF f = 60 Hz, RL = 2.2 kΩ CMRR - 100 - dB Common mode rejection ratio Rev. 2.4, 16-May-2022 Document Number: 83622 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IL300 www.vishay.com Vishay Semiconductors SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION Climatic classification SYMBOL VALUE According to IEC 68 part 1 UNIT 55 / 100 / 21 Comparative tracking index CTI 175 VISO 4420 VRMS Maximum transient isolation voltage VIOTM 10 000 Vpeak Maximum repetitive peak isolation voltage VIORM 890 Vpeak VIO = 500 V, Tamb = 25 °C RIO ≥ 1012 Ω VIO = 500 V, Tamb = 100 °C RIO ≥ 1011 Ω Output safety power PSO 400 mW Input safety current ISI 275 mA Safety temperature TS 175 °C ≥7 mm ≥7 mm ≥8 mm ≥8 mm ≥ 0.4 mm Maximum rated withstanding isolation voltage Isolation resistance t = 1 min Creepage distance DIP-8 Clearance distance Creepage distance DIP-8, 400 mil, option 6; SMD-8, option 7; SMD-8, option 9 Clearance distance Insulation thickness DTI Note • As per IEC 60747-5-5, § 7.4.3.8.2, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Axis Title Axis Title 10000 100 10000 300 100 1 10 0.1 1.0 1.2 1.4 1.6 200 1000 Tamb = 0 °C Tamb = 25 °C 1st line 2nd line 1000 2nd line IP1 - Servo Photocurrent (μA) Tamb = 25 °C 10 1st line 2nd line 2nd line IF - Forward Current (mA) Tamb = -55 °C Tamb = 100 °C 100 100 Tamb = 85 °C 10 0 0 5 10 15 20 25 VF - Forward Voltage (V) IF - Forward Current (mA) Fig. 3 - Forward Voltage vs. Forward Current Fig. 4 - Servo Photocurrent vs. Forward Current Rev. 2.4, 16-May-2022 Document Number: 83622 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IL300 www.vishay.com Vishay Semiconductors Axis Title 10000 Normalized to: IF = 10 mA, VD = -15 V, Tamb = 25 °C 7 6 Tamb = 25 °C 1000 Tamb = 0 °C 5 1st line 2nd line 2nd line NIP1 - Normalized Photodiode Current 8 4 Tamb = -55 °C Tamb = 100 °C 3 100 Tamb = 85 °C 2 1 0 0 10 20 30 40 50 10 IF - Forward Current (mA) Fig. 5 - Normalized Photodiode Current vs. Forward Current Axis Title 10000 0.015 Tamb = -55 °C Tamb = 0 °C 1000 0.010 1st line 2nd line 2nd line K1 - Servo Gain (IP1/IF) Tamb = 25 °C Tamb = 85°C Tamb = 100 °C 0.005 100 10 0.000 0 10 20 30 40 50 IF - Forward Current (mA) Fig. 6 - Servo Gain vs. Forward Current Axis Title 10000 Normalized to: IF = 10 mA, Tamb = 25 °C 1.03 1.02 Tamb = 25 °C 1.01 Tamb = 0 °C Tamb = -55 °C 1000 1st line 2nd line 2nd line NK3 - Normalized Transfer Gain (K2/K1) 1.04 1.00 0.99 Tamb = 100 °C 100 Tamb = 85 °C 0.98 0.97 10 0.96 0 10 20 30 40 50 IF - Forward Current (mA) Fig. 7 - Normalized Transfer Gain vs. Forward Current Rev. 2.4, 16-May-2022 Document Number: 83622 5 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IL300 www.vishay.com Vishay Semiconductors 0.95 ± 0.15 0.70 ± 0.15 0.86 ± 0.10 0.50 ± 0.10 1.27 ± 0.10 2.54 nom. 4 3 2 7.62 typ. 6.50 ± 0.1 6.00 ± 0.15 10.16 max. 9.75 ± 0.15 3.10 ± 0.15 3.55 ± 0.15 PACKAGE DIMENSIONS (in millimeters) 3° to 9 0.25 ± 0.05 ° 1 Pin one ID ISO method A 5 6 7 8 hm Option 6 Option 7 10.16 ± 0.2 7.62 typ. Option 9 9.78 ± 0.25 7.62 typ. 7.62 typ. 0.7 ± 0.2 3.55 ± 0.15 0.25 ± 0.05 8 min. 0.75 ± 0.2 8 min. 8.4 min. 0.25 ± 0.05 10.55 ± 0.4 10.05 ± 0.25 0.030 (0.76) 0.100 (2.54) 0.030 (0.76) R 0.010 (0.25) R 0.010 (0.25) 0.100 (2.54) 0.070 (1.78) 0.315 (8.00) min. 0.060 (1.52) 0.435 (11.05) 0.070 (1.78) 0.315 (8.00) min. 0.060 (1.52) 0.435 (11.05) PACKAGE MARKING IL300-F V YWW 68 Fig. 8 - Example of IL300-F-X001 Rev. 2.4, 16-May-2022 Document Number: 83622 6 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 IL300 www.vishay.com Vishay Semiconductors SOLDER PROFILES HANDLING AND STORAGE CONDITIONS ESD level: HBM class 2 Axis Title 10000 300 Floor life: unlimited Max. 260 °C 255 °C 240 °C 217 °C 2nd line Temperature (°C) 250 Conditions: Tamb < 30 °C, RH < 85 % 245 °C Moisture sensitivity level 1, according to J-STD-020 1000 200 1st line 2nd line Max. 30 s 150 Max. 120 s Max. 100 s 100 Max. ramp down 6 °C/s 100 Max. ramp up 3 °C/s 50 10 0 0 50 100 150 200 250 300 Time (s) 19841 Fig. 9 - Lead (Pb)-free Reflow Solder Profile According to J-STD-020 for SMD Devices Axis Title 300 10000 5s Lead temperature 200 235 °C to 260 °C First wave 1000 ca. 2 K/s ca. 200 K/s 150 Full line: typical Dotted lines: process limits Second wave 1st line 2nd line 2nd line Temperature (°C) 250 100 °C to 130 °C 100 100 2 K/s 50 ca. 5 K/s Forced cooling 10 0 0 50 100 150 200 250 Time (s) 948626 Fig. 10 - Wave Soldering Double Wave Profile According to J-STD-020 for DIP Devices Rev. 2.4, 16-May-2022 Document Number: 83622 7 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000