K3021P

Not for New Designs - Alternative Device: VO3021, VO3022, VO3023 K3020P, K3020PG Series www.vishay.com Vishay Semiconductors Optocoupler, Phototriac Output, Non-Zero Crossing, 400 VDRM FEATURES • 400 V blocking voltage • Wide range of trigger current 6 MT2 A 1 • 100 mARMS on-state current • Wide temperature range -55 °C to +100 °C 5 NC C 2 • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 4 MT1 NC 3 APPLICATIONS • Power TRIAC driver • Isolated AC load switch • Air condition • Heaters DESCRIPTION • White goods The K3020P, K3020PG series consists of a phototriac optically coupled to a gallium arsenide infrared-emitting diode in a 6-lead plastic dual inline package. • Industrial controls The non-zero crossing functionality enables full wave control. Featuring galvanic and electrical noise isolation, the output is able to directly switch AC loads or drive medium to high power TRIACs. AGENCY APPROVALS • Office equipment • UL • cUL • DIN EN 60747-5-5 (VDE 0884-5) • CQC: GB4943-1-2011 • CQC: GB8898-2011 • FIMKO ORDERING INFORMATION K 3 0 2 PART NUMBER X TRIGGER CURRENT BIN AGENCY CERTIFIED / PACKAGE VDE, cUL, BSI DIP-6 DIP-6, 400 mil P G PACKAGE OPTION DIP-6 G leadform 7.62 mm 10.16 mm TRIGGER CURRENT, IFT 5 mA 10 mA 15 mA 30 mA K3023P K3022P K3021P K3020P K3023PG K3022PG K3021PG K3020PG Note • Additional options may be possible, please contact sales office. Document Number: 83505 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.6, 06-Oct-2022 Not for New Designs - Alternative Device: VO3021, VO3022, VO3023 K3020P, K3020PG Series www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT INPUT Reverse voltage VR 5 V Forward current IF 80 mA Surge current P.W. < 10 μs IFSM 3 A Pdiss 100 mW Tj 125 °C Peak off-state voltage VDRM 400 V On-state RMS current ID(RMS) 100 mA Power dissipation Junction temperature OUTPUT Peak surge current tp ≤ 10 ms Power dissipation Junction temperature IFSM 1.5 A Pdiss 300 mW Tj 125 °C COUPLER Total power dissipation Ptot 350 mW Storage temperature range Tstg -55 to +150 °C Ambient temperature Tamb -55 to +100 °C Tsld 260 °C Lead soldering temperature 2 mm from case, t < 10 s Note • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage IF = 50 mA VF - 1.3 1.6 V Reverse voltage IR = 10 μA VR 5 - - V VR = 0 V, f = 1 MHz Cj - 50 - pF Forward peak off-state voltage (repetitive) IDRM = 100 nA VDRM (1) 400 - - V Peak on-state voltage Junction capacitance OUTPUT ITM = 100 mA VTM - 1.5 3 V Critical rate of rise of off-state voltage IF = 0 A, VD = 0.67 VDRM dV/dtcr - 10 - V/μs Critical rate of rise of on-state current commutation VD = 30 VRMS, ID = 15 mARMS dV/dtcrq 0.1 0.15 - V/μs mA COUPLER (2) Emitting diode trigger current Holding current VS = 3 V, RL = 150 Ω IF = 10 mA, VS ≥ 3 V K3020P IFT - 15 30 K3020PG IFT - 15 30 mA K3021P IFT - 8 15 mA K3021PG IFT - 8 15 mA K3022P IFT - 5 10 mA K3022PG IFT - 5 10 mA K3023P IFT - 3 5 mA K3023PG IFT - 3 5 mA IH - 200 - μA Notes • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. (1) Test voltage must be applied within dV/dt ratings. (2) I is defined as a minimum trigger current. FT Document Number: 83505 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.6, 06-Oct-2022 Not for New Designs - Alternative Device: VO3021, VO3022, VO3023 K3020P, K3020PG Series www.vishay.com Vishay Semiconductors SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL Climatic classification According to IEC 68 part 1 Pollution degree According to DIN VDE 0109 Comparative tracking index UNIT 2 Insulation group IIIa Maximum rated withstanding isolation voltage VALUE 55 / 100 / 21 CTI 175 According to UL1577, t = 1 min VISO 4420 VRMS Tested withstanding isolation voltage According to UL1577, t = 1 s VISO 5300 VRMS Maximum transient isolation voltage According to DIN EN 60747-5-5 VIOTM 8000 Vpeak Maximum repetitive peak isolation voltage According to DIN EN 60747-5-5 VIORM 890 Vpeak VIO = 500 V, Tamb = 25 °C RIO ≥ 1012 Ω VIO = 500 V, Tamb = 100 °C RIO ≥ 1011 Ω Isolation resistance Output safety power PSO 265 mW Input safety current ISI 130 mA Input safety temperature TS 150 °C ≥7 mm Creepage distance DIP-6 Clearance distance Creepage distance DIP-6, 400 mil Clearance distance Insulation thickness VIORM x 1.6 = VPR, 100 % sample test with tM = 10 s, partial discharge < 5 pC Input to output test voltage, method A ≥7 mm ≥8 mm ≥8 mm DTI ≥ 0.4 mm VPR 1424 Vpeak Note • As per IEC 60747-5-5, § 7.4.3.8.2, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Axis Title 400 10000 1000 1000 200 100 Input 100 IF - Forward Current (mA) Output 300 1st line 2nd line 2nd line Pdiss - Power Dissipation (mW) Total 100 10 1 0.1 10 0 -60 -40 -20 0 20 40 60 80 100 120 0 0.4 0.8 1.2 1.6 2.0 VF - Forward Voltage (V) Tamb - Ambient Temperature (°C) Fig. 1 - Total Power Dissipation vs. Ambient Temperature Fig. 2 - Forward Current vs. Forward Voltage Document Number: 83505 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.6, 06-Oct-2022 Not for New Designs - Alternative Device: VO3021, VO3022, VO3023 K3020P, K3020PG Series Vishay Semiconductors 100 1.5 1.4 1.3 VS = 3 V R L = 150 : 1.2 1.1 1.0 0.9 0.8 0.7 0.6 I DRM - Off-State Current (nA) I FTrel - Relative Threshold Forward Current www.vishay.com V DR = 100 V IF = 0 10 1 0.5 -30 -20 -10 0 10 20 30 40 50 60 70 80 20 Tamb - Ambient Temperature (°C) Fig. 3 - Relative Threshold Forward Current vs. Ambient Temperature Fig. 5 - Off-State Current vs. Ambient Temperature 250 200 1.4 1.2 IF = I FT I T = 100 mA 1.1 1.0 0.9 0.8 0.7 I TM - On-State Current (mA) VTMrel - Relative On-State Voltage 1.5 1.3 30 40 50 60 70 80 90 100 Tamb - Ambient Temperature (°C) 150 100 I FT = 15 mA 50 0 - 50 - 100 - 150 0.6 - 200 0.5 -30 -20 -10 0 10 20 30 40 50 60 70 80 Tamb - Ambient Temperature (°C) - 250 -2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 Fig. 4 - Relative On-State vs. Ambient Temperature V TM - On-State Voltage (V) Fig. 6 - On-State Current vs. On-State Voltage Document Number: 83505 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.6, 06-Oct-2022 Not for New Designs - Alternative Device: VO3021, VO3022, VO3023 K3020P, K3020PG Series www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS (in millimeters) DIP-6 9.00 max. 7.62 typ. 8.60 ± 0.10 6.50 ± 0.25 0.79 min. 3.10 ± 0.50 3.55 ± 0.25 0.90 min. 0.85 ± 0.10 0.50 ± 0.10 3° to 9° 0.25 ± 0.10 1.27 ± 0.10 2.54 typ. 6 5 4 1 2 3 Pin one I.D. DIP-6, 400 mil 10.16 typ. 9.00 max. 7.62 typ. 8.60 ± 0.10 6.50 ± 0.25 0.10 min. 3.05 ± 0.50 3.55 ± 0.25 0.90 min. 0.85 ± 0.10 0.50 ± 0.10 1.27 ± 0.10 2.54 typ. 6 5 4 1 2 3 0.25 ± 0.10 10.55 ± 0.40 Pin one I.D. Document Number: 83505 5 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.6, 06-Oct-2022 Not for New Designs - Alternative Device: VO3021, VO3022, VO3023 K3020P, K3020PG Series www.vishay.com Vishay Semiconductors PACKAGE MARKING K3020P V YWW H 68 Fig. 7 - Example of K3020P Notes • The “G” of the G leadform type is not marked on the body. • The VDE logo is only marked on ption1 parts. PACKAGING INFORMATION (in millimeters) DIP-6 528 ± 0.2 330 ± 0.5 260 ± 0.5 200 ± 0.5 150 ± 0.5 125 ± 0.5 – 1.0 30 ± 0.5 B VISHAY OPTOSEMICONDUCTOR MADE IN MALAYSIA ANTISTATIC Detail B Detail A A – 1.0 – 1.0 3 ± 0.5 – 1.0 380 ± 1 0.7 ± 0.5 13 x 10 = 130 12 ± 0.3 B 6.6 ± 0.3 Transparent rigid PVC 1 2.7 ± 0.2 R 0. 6° 4.4 ± 0.3 1.0 14 x 0. 5 11 ± 0.3 R 0.6 ± 0.1 10° A // 0.2 B Detail A Detail B 5.7 ± 0.15 17996 Section A - B Not to scale Document Number: 83505 6 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.6, 06-Oct-2022 Not for New Designs - Alternative Device: VO3021, VO3022, VO3023 K3020P, K3020PG Series www.vishay.com Vishay Semiconductors DIP-6, 400 mil 0.5 13.6 5.7 9 4.3 15.3 15912 SHIPPING INFORMATION With stopper pins tolerance: ± 0.5 length: 575 ± 5 HANDLING AND STORAGE CONDITIONS ESD level: HBM class 2 DEVICES PER TUBS TYPE UNITS/TUBE TUBES/BOX UNITS/BOX DIP-6 50 40 2000 Floor life: unlimited Conditions: Tamb < 30 °C, RH < 85 % Moisture sensitivity level 1, according to J-STD-020 SOLDER PROFILES Axis Title 300 10000 5s Lead temperature 200 235 °C to 260 °C First wave 1000 ca. 2 K/s ca. 200 K/s 150 Full line: typical Dotted lines: process limits Second wave 1st line 2nd line 2nd line Temperature (°C) 250 100 °C to 130 °C 100 100 2 K/s 50 ca. 5 K/s Forced cooling 10 0 0 50 100 150 200 250 Time (s) 948626 Fig. 8 - Wave Soldering Double Wave Profile According to J-STD-020 for DIP Devices Document Number: 83505 7 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Rev. 2.6, 06-Oct-2022 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000