MCT6

MCT6 Vishay Semiconductors Optocoupler, Phototransistor Output, Dual Channel FEATURES • Current transfer ratio, 50 % typical • Leakage current, 1.0 nA typical A 1 8 E • Two isolated channels per package C 2 7 C C 3 6 C • Compliant to RoHS Directive accordance to WEEE 2002/96/EC A 4 5 E and in AGENCY APPROVALS • UL1577, file no. E52744 system code H, double protection • DIN EN 60747-5-2 (VDE 0884)/DIN EN 60747-5-5 pending available with option 1 • CSA 93751 i179073 • BSI IEC 60950; IEC 60065 DESCRIPTION The MCT6 is a two channel optocoupler for high density applications. Each channel consists of an optically coupled pair with a gallium arsenide infrared LED and a silicon NPN phototransistor. Signal information, including a DC level, can be transmitted by the device while maintaining a high degree of electrical isolation between input and output. The MCT6 is especially designed for driving medium-speed logic, where it may be used to eliminate troublesome ground loop and noise problems. It can also be used to replace relays and transformers in many digital interface applications, as well as analog applications such as CRT modulation. ORDERING INFORMATION DIP M C T PART NUMBER 6 - X 0 0 # PACKAGE OPTION T TAPE AND REEL 7.62 mm Option 7 > 0.7 mm AGENCY CERTIFIED/PACKAGE Option 9 > 0.1 mm CTR  20 UL, CSA, BSI DIP-8 MCT6 SMD-8, option 7 MCT6-X007T (1) SMD-8, option 9 MCT6-X009T (1)  20 VDE, UL, CSA, BSI DIP-8 MCT6-X001 Notes • Additional options may be possible, please contact sales office. (1) Also available in tubes, do not put “T” on the end. Document Number: 83645 Rev. 1.6, 17-May-11 For technical questions, contact: optocoupleranswers@vishay.com www.vishay.com 1 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MCT6 Optocoupler, Phototransistor Output, Vishay Semiconductors Dual Channel ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT 60 mA 1.0 μs pulse, 300 pps IFM 3.0 A Pdiss 100 mW 1.3 mW/°C mA INPUT Rated forward current, DC Peak forward current, DC Power dissipation Derate linearly from 25 °C OUTPUT Collector current Collector emitter breakdown voltage Power dissipation IC 30 BVCEO 30 V Pdiss 150 mW 2.0 mW/°C 5300 VRMS Derate linearly from 25 °C COUPLER Isolation test voltage VISO Isolation resistance VIO = 500 V, Tamb = 25 °C RIO VIO = 500 V, Tamb = 100 °C RIO M Creepage distance  1012  1011   7.0 mm  7.0 mm Ptot 400 mW 5.33 mW/°C Storage temperature Tstg - 55 to + 150 °C Operating temperature Tamb - 55 to + 100 °C 10 s Clearance distance Total package dissipation Derate linearly from 25 °C Lead soldering time at 260 °C Note • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL Forward voltage IF = 20 mA Reverse current VR = 3.0 V MIN. TYP. MAX. UNIT VF 1.25 1.50 V IR 0.1 10 μA VF = 0 V Cj 25 pF Collector emitter breakdown voltage IC = 1.0 μA, IE = 10 μA BVCEO 30 65 V Emitter collector breakdown voltage IC = 10 A, IE = 10 μA BVECO 7.0 10 Collector emitter leakage current VCE = 10 V ICEO 1.0 Collector emitter capacitance VCE = 0 V CCE 8.0 IC = 2.0 mA, IF = 16 mA VCEsat Capacitance (input to output) f = 1.0 MHz CIO 0.5 pF Capacitance between channels f = 1.0 MHz 0.4 pF IC = 2.0 mA, VCC = 10 V, RL = 100  150 kHz INPUT Junction capacitance OUTPUT V 100 nA pF COUPLER Saturation voltage, collector emitter Bandwidth 0.40 V Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. Document Number: 83645 Rev. 1.6, 17-May-11 For technical questions, contact: optocoupleranswers@vishay.com www.vishay.com 2 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MCT6 Vishay Semiconductors Optocoupler, Phototransistor Output, Dual Channel CURRENT TRANSFER RATIO (Tamb = 25 °C, unless otherwise specified) PARAMETER DC current transfer ratio TEST CONDITION SYMBOL MIN. TYP. IF = 10 mA, VCE = 10 V CTRDC 20 50 MAX. UNIT % SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER Switching times, output transistor TEST CONDITION SYMBOL IC = 2.0 mA, RL = 100 , VCE = 5 V ton, toff MIN. TYP. MAX. UNIT 3.0 μs TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 1.5 1.4 Normalized to: VCE = 10 V, IF = 10 mA,TA = 25 °C Tamb = - 55 °C NCTR - Normalized CTR VF - Forward Voltage (V) 1.3 1.2 Tamb = 25 °C 1.1 1.0 0.9 Tamb = 85 °C 0.8 1 10 IF - Forward Current (mA) 100 0.5 NCTR(SAT) NCTR 10 100 iilct6_03 Fig. 1 - Forward Voltage vs. Forward Current 1.5 Fig. 3 - Normalized Non-Saturated and Saturated CTR vs. LED Current 1.5 Tamb = 25 °C 1.0 CTRCE(sat) VCE = 0.4 V 0.5 NCTR(SAT) NCTR NCTR - Normalized CTR Normalized to: VCE = 10 V, IF = 10 mA Normalized to: VCE = 10 V, IF = 10 mA Tamb = 25 °C 1.0 CTRCE(sat) VCE = 0.4 V Tamb = 70 °C 0.5 NCTR(SAT) NCTR 0.0 0.0 0.1 1 10 100 0.1 IF - LED Current (mA) 1 10 100 IF - LED Current (mA) iilct6_04 iilct6_02 Fig. 2 - Normalized Non-Saturated and Saturated CTR vs. LED Current www.vishay.com 3 1 IF - LED Current (mA) iilct6_01 NCTR - Normalized CTR TA = 50 °C 0.0 0.1 0.7 0.1 CTRCE(sat) VCE = 0.4 V 1.0 Fig. 4 - Normalized Non-Saturated and Saturated CTR vs. LED Current For technical questions, contact: optocoupleranswers@vishay.com Document Number: 83645 Rev. 1.6, 17-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MCT6 Optocoupler, Phototransistor Output, Vishay Semiconductors Dual Channel 1000 2.5 Normalized to: Tamb = 25 °C, IF = 10 mA VCC = 5 V, Vth = 1.5 V tpLH - Propagation (µs) NCTR - Normalized CTR VCE = 10 V, IF = 10 mA, Tamb = 25 °C CTRCE(sat) VCE = 0.4 V 1.0 Tamb = 85 °C 0.5 tpHL 2.0 100 10 1.5 tpLH NCTR(SAT) NCTR 0.0 0.1 1 10 1 0.1 100 1 tpHL - Propagation Delay (µs) 1.5 1.0 100 10 R L- Collector Load Resistor (kΩ) IF - LED Current (mA) iilct6_05 iilct6_08 Fig. 8 - Propagation Delay vs. Collector Load Resistor Fig. 5 - Normalized Non-Saturated and Saturated CTR vs. LED Current IF 35 ICE - Collector Current (mA) 30 25 50 °C 20 15 t PHL 70 °C 25 °C t PLH 85 °C VO 10 5 tS 50 % 0 0 10 20 30 40 50 60 IF - LED Current (mA) iilct6_06 iilct6_09 Fig. 6 - Collector Emitter Current vs. Temperature and LED Current tD tR tF Fig. 9 - Switching Timing I CEO - Collector Emitter (nA) 105 104 V CC = 5 V 103 102 IF = 10 mA Vce = 10 V 101 Typical 100 VO 10- 1 f = 10 kHz, -2 DF = 50 % 10 - 20 0 20 40 60 80 R L = 100 Ω 100 Tamb - Ambient Temperature (°C) iilct6_10 iilct6_07 Fig. 7 - Collector Emitter Leakage Current vs.Temperature Document Number: 83645 Rev. 1.6, 17-May-11 Fig. 10 - Switching Schematic For technical questions, contact: optocoupleranswers@vishay.com www.vishay.com 4 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MCT6 Vishay Semiconductors Optocoupler, Phototransistor Output, Dual Channel PACKAGE DIMENSIONS in millimeters Pin one ID 4 3 2 1 5 6 7 8 6.645 ± 0.165 ISO method A 9.77 ± 0.14 0.95 ± 0.19 7.62 typ. 0.79 4° typ. 3.555 ± 0.255 6.095 ± 0.255 1.27 10° 3.045 ± 0.255 0.70 ± 0.19 3° to 9° 0.51 ± 0.05 2.54 typ. 0.25 ± 0.05 i178006 Option 7 Option 9 7.62 typ. 9.53 10.03 7.62 ref. 0.7 4.6 4.1 0.102 0.249 8 min. 0.30 typ. 0.51 1.02 15° max. 8.4 min. 8 min. 10.3 max. 0.76 2.54 R 0.25 0.76 2.54 R 0.25 1.78 18450-8 8 min. 11.05 1.52 1.78 8 min. 11.05 1.52 PACKAGE MARKING MCT6 V WWY H 68 Notes • Only options 1 and 7 reflected in the package marking • The VDE logo is only marked on option 1 parts • Tape and reel suffix (T) is not part of the package marking www.vishay.com 5 For technical questions, contact: optocoupleranswers@vishay.com Document Number: 83645 Rev. 1.6, 17-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000