RCA1206100KFKEA

RCA e3 www.vishay.com Vishay Draloric Sulfur Resistant Thick Film Chip Resistors FEATURES • Superior resistance against sulfur containing atmosphere, according to ASTM B809-95 • Stability at different environmental conditions ΔR/R ≤ 1 % (1000 h rated power at 70 °C) • AEC-Q200 qualified • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 LINKS TO ADDITIONAL RESOURCES APPLICATIONS 3D 3D • Automotive 3D Models • ADAS The sulfur resistant, thick film chip resistors series is the perfect choice for most fields of harsh environment electronics operation, where reliability and stability are of major concern. Typical applications include automotive, ADAS, industrial, and commercial applications which operate in harsh environment. • Industrial • Commercial TECHNICAL SPECIFICATIONS DESCRIPTION Imperial size Metric size code RCA0402 e3 0402 RR1005M RCA0805 e3 0805 RR2012M RCA1210 e3 1210 RR3225M 0.063 W 0.10 W 50 V 75 V RCA1218 e3 1218 RR3246M 1 Ω to 2.2 MΩ; jumper (0 Ω) ± 5 %; ± 1 %; ± 0.5 % ± 200 ppm/K; ± 100 ppm/K; ± 50 ppm/K 0.125 W 0.25 W 0.5 W 1.0 W 150 V 200 V 200 V RCA2010 RCA2512 e3 e3 2010 2512 RR5025M RR6332M 1 Ω to 10 MΩ; jumper (0 Ω) 0.75 W 1.0 W 200 V 400 V 500 V 300 V 300 V 300 V 155 °C ϑF max. (1) Operating temperature range Maximum resistance change at P70 for resistance range, |ΔR/R| after: 1000 h Permissible voltage against ambient (insulation): 1 min, Uins Failure rate: FITobserved RCA1206 e3 1206 RR3216M 1 Ω to 10 MΩ; jumper (0 Ω) Resistance range Resistance tolerance Temperature coefficient Rated dissipation, P70 (1) Operating voltage, Umax. ACRMS/DC Permissible film temperature, RCA0603 e3 0603 RR1608M -55 °C to +155 °C ≤ 1.0 % 75 V 100 V 200 V 300 V 300 V ≤ 0.1 x 10-9/h Note (1) Please refer to APPLICATION INFORMATION below APPLICATION INFORMATION When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted film temperature is not exceeded. These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. Revision: 04-Jul-2022 Document Number: 20037 1 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCA e3 www.vishay.com Vishay Draloric TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE / SIZE RCA0402 e3 RCA0603 e3 RCA0805 e3 RCA1206 e3 RCA1210 e3 RCA1218 e3 RCA2010 e3 RCA2512 e3 TCR TOLERANCE RESISTANCE E-SERIES ± 200 ppm/K ±5% 1.0 Ω to 10 MΩ E24 ± 200 ppm/K ±1% 1.0 Ω to 9.76 Ω E24; E96 ± 100 ppm/K ±1% 10 Ω to 10 MΩ E24; E96 ± 100 ppm/K ± 0.5 % 10 Ω to 1.0 MΩ E24; E96 ± 50 ppm/K ± 0.5 %; ± 1 % 100 Ω to 1.0 MΩ E24; E96 Jumper, Imax. = 1.5 A ≤ 20 mΩ 0Ω - ± 200 ppm/K ±5% 1.0 Ω to 10 MΩ E24 ± 100 ppm/K ±1% 1.0 Ω to 10 MΩ E24; E96 ± 100 ppm/K ± 0.5 % 10 Ω to 10 MΩ E24; E96 E24; E96 ± 50 ppm/K ± 0.5 %; ± 1 % 100 Ω to 10 MΩ Jumper, Imax. = 2.0 A ≤ 20 mΩ 0Ω - ± 200 ppm/K ±5% 1.0 Ω to 10 MΩ E24 ± 100 ppm/K ±1% 1.0 Ω to 10 MΩ E24; E96 ± 100 ppm/K ± 0.5 % 10 Ω to 10 MΩ E24; E96 E24; E96 ± 50 ppm/K ± 0.5 %; ± 1 % 100 Ω to 10 MΩ Jumper, Imax. = 2.5 A ≤ 20 mΩ 0Ω - ± 200 ppm/K ±5% 1.0 Ω to 10 MΩ E24 ± 100 ppm/K ±1% 1.0 Ω to 10 MΩ E24; E96 ± 100 ppm/K ± 0.5 % 10 Ω to 10 MΩ E24; E96 ± 50 ppm/K ± 0.5 %; ± 1 % 100 Ω to 10 MΩ E24; E96 Jumper, Imax. = 3.5 A ≤ 20 mΩ 0Ω - ± 200 ppm/K ±5% 1.0 Ω to 10 MΩ E24 ± 100 ppm/K ±1% 1.0 Ω to 10 MΩ E24; E96 ± 100 ppm/K ± 0.5 % 10 Ω to 1.0 MΩ E24; E96 ± 50 ppm/K ± 0.5 %; ± 1 % 100 Ω to 1.0 MΩ E24; E96 Jumper, Imax. = 5.0 A ≤ 20 mΩ 0Ω - ± 200 ppm/K ±5% 1.0 Ω to 2.2 MΩ E24 ± 100 ppm/K ±1% 1.0 Ω to 2.2 MΩ E24; E96 ± 100 ppm/K ± 0.5 % 100 Ω to 2.2 MΩ E24; E96 ± 50 ppm/K ± 0.5 %; ± 1 % 100 Ω to 2.2 MΩ E24; E96 Jumper, Imax. = 7.0 A ≤ 20 mΩ 0Ω - ± 200 ppm/K ±5% 1.0 Ω to 10 MΩ E24 ± 100 ppm/K ±1% 1.0 Ω to 10 MΩ E24; E96 ± 100 ppm/K ± 0.5 % 10 Ω to 10 MΩ E24; E96 ± 50 ppm/K ± 0.5 %; ± 1 % 100 Ω to 10 MΩ E24; E96 Jumper, Imax. = 6.0 A ≤ 20 mΩ 0Ω - ± 200 ppm/K ±5% 1.0 Ω to 10 MΩ E24 ± 100 ppm/K ±1% 1.0 Ω to 10 MΩ E24; E96 ± 100 ppm/K ± 0.5 % 10 Ω to 10 MΩ E24; E96 ± 50 ppm/K ± 0.5 %; ± 1 % 100 Ω to 10 MΩ E24; E96 Jumper, Imax. = 7.0 A ≤ 20 mΩ 0Ω - Note • The temperature coefficient of resistance (TCR) is not specified for 0 Ω jumpers Revision: 04-Jul-2022 Document Number: 20037 2 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCA e3 www.vishay.com Vishay Draloric PACKAGING TYPE / SIZE RCA0402 e3 RCA0603 e3 RCA0805 e3 RCA1206 e3 RCA1210 e3 RCA1218 e3 RCA2010 e3 RCA2512 e3 CODE QUANTITY ED = ET7 EC = ET6 EE = EF4 EA = ET1 EB = ET5 EC = ET6 EA = ET1 EB = ET5 EC = ET6 EA = ET1 EB = ET5 EC = ET6 EA = ET1 EB = ET5 EC = ET6 EK = ET9 EF = E02 EG = E67 EH = E82 10 000 20 000 50 000 5000 10 000 20 000 5000 10 000 20 000 5000 10 000 20 000 5000 10 000 20 000 4000 4000 2000 4000 PACKAGING STYLE Paper tape according to IEC 60286-3, type 1a Blister tape according to IEC 60286-3, type 2a WIDTH PITCH 8 mm 2 mm 8 mm 4 mm 8 mm 4 mm 8 mm 4 mm 8 mm 4 mm 12 mm 12 mm 4 mm 4 mm 8 mm 4 mm 12 mm PACKAGING DIMENSIONS Ø 180 mm / 7" Ø 285 mm / 11.25" Ø 330 mm / 13" Ø 180 mm / 7" Ø 285 mm / 11.25" Ø 330 mm / 13" Ø 180 mm / 7" Ø 285 mm / 11.25" Ø 330 mm / 13" Ø 180 mm / 7" Ø 285 mm / 11.25" Ø 330 mm / 13" Ø 180 mm / 7" Ø 285 mm / 11.25" Ø 330 mm / 13" Ø 180 mm / 7" Ø 180 mm / 7" Ø 180 mm / 7" PART NUMBER AND PRODUCT DESCRIPTION Part Number: RCA080510K0FKEA Part Number: RCA08050000ZSEC R C A 0 8 0 5 1 0 K 0 F K E A TYPE / SIZE VALUE TOLERANCE TCR PACKAGING RCA0402 RCA0603 RCA0805 RCA1206 RCA1210 RCA1218 RCA2010 RCA2512 R = decimal K = thousand M = million 0000 = 0 Ω jumper D = ± 0.5 % F=±1% J=±5% Z = jumper H = ± 50 ppm/K K = ± 100 ppm/K N = ± 200 ppm/K S = jumper EA, EB, EC, ED, EE, EF, EG, EH, EK Product Description: RCA0805 100 10K 1 % ET1 e3 Product Description: RCA0805 0R0 ET6 e3 RCA0805 100 10K 1% TYPE / SIZE TCR RESISTANCE RCA0402 RCA0603 RCA0805 RCA1206 RCA1210 RCA1218 RCA2010 RCA2512 ± 50 ppm/K ± 100 ppm/K ± 200 ppm/K 10R = 10 Ω 10K = 10 kΩ 1M = 1 MΩ 0R0 = jumper Revision: 04-Jul-2022 ET1 e3 TOLERANCE PACKAGING LEAD (Pb)-FREE ± 0.5 % ±1% ±5% ET1, ET5, ET6, ET7, EF4, E02, E67, E82, ET9 e3 = pure tin termination finish Document Number: 20037 3 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCA e3 www.vishay.com DESCRIPTION Production is strictly controlled and follows an extensive set of instructions established for reproducibility. A cermet film layer and a glass-over are deposited on a high grade (Al2O3) ceramic substrate with its prepared inner contacts on both sides. A special laser is used to achieve the target value by smoothly fine trimming the resistive layer without damaging the ceramics. A special process is used to ensure resistor long term operation in harsh environment (sulfur atmosphere). The resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. The terminations receive a final pure tin on nickel plating. The result of the determined production is verified by an extensive testing procedure on 100 % of the individual chip resistors. Only accepted products are laid directly into the tape in accordance with IEC 60286-3 Type 1a and Type 2a (1). ASSEMBLY The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic soldering wave, reflow or vapor phase as shown in IEC 61760-1 (1). The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. The suitability of conformal coatings, potting compounds and their processes, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. The resistors are RoHS-compliant, the pure tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. Solderability is specified for 2 years after production or requalification. The permitted storage time is 20 years. The immunity of the plating against tin whisker growth has been proven under extensive testing. MATERIALS Vishay Draloric The products do not contain any of the banned substances as per IEC 62474, GADSL, or the SVHC list, see www.vishay.com/how/leadfree. Hence the products fully comply with the following directives: • 2000/53/EC End-of-Life Vehicle Directive (ELV) and Annex II (ELV II) • 2011/65/EU Restriction of the Use of Hazardous Substances Directive (RoHS) with amendment 2015/863/EU • 2012/19/EU Waste Electrical and Electronic Equipment Directive (WEEE) Vishay pursues the elimination of conflict minerals from its supply chain, see the Conflict Minerals Policy at www.vishay.com/doc?49037. APPROVALS The resistors are qualified according to AEC-Q200. Where applicable, the resistors are tested in accordance with EN 140401-802 which refers to EN 60115-1, EN 60115-8 and the variety of environmental test procedures of the IEC 60068 (1) series. RELATED PRODUCTS D/CRCW e3 series is not designed for sulfur-containing environment applications. For ordering D/CRCW e3 products please refer to latest edition of datasheet: www.vishay.com/doc?20035. For products with sulfur resistance, superior surge and pulse performance, please refer to datasheet: RCA-IF e3, Pulse Proof Thick Film Chip Resistors www.vishay.com/doc?20059. For products with sulfur resistance and high power rating, please refer to datasheet: RCA-HP e3, Pulse Proof High Power Thick Film Chip Resistors www.vishay.com/doc?20065. Vishay acknowledges the following systems for the regulation of hazardous substances: • IEC 62474, Material Declaration for Products of and for the Electrotechnical Industry, with the list of declarable substances given therein (2) • The Global Automotive Declarable Substance List (GADSL) (3) • The REACH regulation (1907/2006/EC) and the related list of substances with very high concern (SVHC) (4) for its supply chain Notes (1) The quoted IEC standards are also released as EN standards with the same number and identical contents (2) The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474 (3) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council and available at www.gadsl.org (4) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table Revision: 04-Jul-2022 Document Number: 20037 4 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCA e3 www.vishay.com Vishay Draloric FUNCTIONAL PERFORMANCE PERFORMANCE IN SULFUR-CONTAINING AMBIANCE HUMID SULFUR VAPOR TEST HUMID SULFUR VAPOR TEST (Accelerated) Reference specification ASTM B809-95 ASTM B809-95 accelerated conditions Test conditions (temperature, humidity) 60 °C ± 2 °C 85 % ± 4 % RH 90 °C ± 2 °C 74 % ± 7 % RH Sulfur (saturated vapor) Sulfur (saturated vapor) TEST NAME Aggressive agent Failure criteria in VI under magnification No silver sulfide growth at the interface No silver sulfide growth at the interface between termination and protective overcoat. between termination and protective overcoat. No signs of mechanical damage. No signs of mechanical damage. Failure criteria in electrical test Time before failure ≤ (± 1 % R + 0.05 Ω) ≤ (± 1 % R + 0.05 Ω) 8000 h 1000 h Single Pulse Axis Title 1000 10 1000 1st line 2nd line 100 2nd line ^ Pmax. - Pulse Load (W) 10000 RCA2512 RCA1218 RCA2010 RCA1210 RCA1206 RCA0805 RCA0603 RCA0402 1 100 0.1 0.01 0.000001 10 0.00001 0.0001 0.001 0.01 0.1 1 10 100 ti - Pulse Duration (s) Maximum pulse load, single pulse; applicable if P → 0 and n < 1000 and Uˆ = Uˆ max.; for permissible resistance change equivalent to 8000 h operation Continuous Pulse Axis Title 10000 RCA2512 RCA1218 RCA2010 RCA1210 RCA1206 RCA0805 RCA0603 RCA0402 100 10 1000 1st line 2nd line 2nd line ^ Pmax. - Continuous Pulse Load (W) 1000 1 100 0.1 0.01 0.000001 10 0.00001 0.0001 0.001 0.01 0.1 1 10 100 ti - Pulse Duration (s) Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑamb) and Uˆ = Uˆ max.; for permissible resistance change equivalent to 8000 h operation Revision: 04-Jul-2022 Document Number: 20037 5 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCA e3 www.vishay.com Vishay Draloric Pulse Voltage Axis Title 2000 10000 RCA2512 RCA2010 RCA1206, RCA1210, RCA1218 RCA0805 RCA0603 RCA0402 1800 1400 1000 1200 1st line 2nd line 2nd line ^ Umax. - Pulse Voltage (V) 1600 1000 800 100 600 400 200 10 0 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 ti - Pulse Duration (s) Maximum pulse voltage, single and continuous pulses; applicable if Pˆ = Pˆ max.; for permissible resistance change equivalent to 8000 h operation Derating Axis Title 1.2 RCA2512, RCA1218 RCA2010 RCA1210 RCA1206 RCA0805 RCA0603 RCA0402 0.8 1000 1st line 2nd line 2nd line P - Power Dissipation (W) 1.0 10000 0.6 100 0.4 0.2 10 0 -70 -60 -50 Revision: 04-Jul-2022 -40 -30 -20 -10 0 10 20 30 40 50 60 70 ϑamb - Ambient Temperature (°C) 80 90 100 110 120 130 140 150 160 Document Number: 20037 6 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCA e3 www.vishay.com Vishay Draloric TESTS AND REQUIREMENTS All executed tests are carried out in accordance with the following specifications: EN 60115-1, generic specification EN 60115-8 (successor of EN 140400), sectional specification EN 140401-802, detail specification IEC 60068-2-xx, test methods The parameters stated in the Test Procedures and Requirements table are based on the required tests and permitted limits of EN 140401-802. The table presents only the most important tests, for the full test schedule refer to the documents listed above. However, some additional tests and a number of improvements against those minimum requirements have been included. The testing also covers most of the requirements specified by EIA/IS-703 and JIS-C-5201-1. The tests are carried out under standard atmospheric conditions in accordance with IEC 60068-1, 4.3, whereupon the following values are applied: Temperature: 15 °C to 35 °C Relative humidity: 25 % to 75 % Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). A climatic category LCT / UCT / 56 is applied, defined by the lower category temperature (LCT), the upper category temperature (UCT), and the duration of exposure in the damp heat, steady state test (56 days). The components are mounted for testing on boards in accordance with EN 60115-8, 2.4.2 unless otherwise specified. TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 (1) TEST METHOD TEST REQUIREMENTS PERMISSIBLE CHANGE (ΔR) PROCEDURE SIZE 0402 Stability for product types: SIZE 0603 TO 2512 STABILITY CLASS 2 OR BETTER RCA e3 1 Ω to 10 MΩ 4.5 - Resistance - ± 5 %; ± 1 %; ± 0.5 % 4.8 - Temperature coefficient (20 / -55 / 20) °C and (20 / 155 / 20) °C ± 200 ppm/K; ± 100 ppm/K; ± 50 ppm/K 4.25.1 - Endurance at 70 °C U = P 70 x R ≤ Umax.; 1.5 h on; 0.5 h off - Endurance at upper category temperature 155 °C, 1000 h 4.24 78 (Cab) Damp heat, steady state (40 ± 2) °C; (93 ± 3) % RH; 56 days; 4.37 67 (Cy) Damp heat, steady state, accelerated (85 ± 2) °C; (85 ± 5) % RH; U = 0.1 x P 85 x R ; U ≤ 100 V; 1000 h 4.23 - Climatic sequence: - 70 °C; 1000 h 4.25.3 ± (1 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) 4.23.2 2 (Ba) Dry heat 125 °C; 16 h 4.23.3 30 (Db) Damp heat, cyclic 55 °C; ≥ 90 % RH; 24 h; 1 cycle 4.23.4 1 (Ab) Cold -55 °C; 2 h 4.23.5 13 (M) Low air pressure 1 kPa; 1 h; (25 ± 10) °C 55 °C; > 90 % RH 4.23.6 30 (Db) Damp heat, cyclic 24 h; 5 cycles - DC load 1 (Aa) Cold -55 °C; 2 h ± (0.25 % R + 0.05 Ω) ± (1 % R + 0.05 Ω) 4.23.7 - U= ± (1 % R + 0.05 Ω) P 70 x R ≤ Umax.; 1 min; 4.19 14 (Na) Rapid change of temperature 30 min at -55 °C and 30 min at 125 °C; 1000 cycles 4.13 - Short time overload U = 2.5 x P 70 x R ≤ 2 x Umax.; whichever is the less severe; 5 s ± (2 % R + 0.05 Ω) 4.27 - Single pulse high voltage overload 10 μs/700 μs Severity no. 4: U = 10 x P 70 x R or U ≤ 2 x Umax.; whichever is the less severe 10 pulses 10 μs / 700 μs ± (1 % R + 0.05 Ω) Revision: 04-Jul-2022 Document Number: 20037 7 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCA e3 www.vishay.com Vishay Draloric TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 (1) TEST METHOD TEST REQUIREMENTS PERMISSIBLE CHANGE (ΔR) PROCEDURE SIZE 0402 Stability for product types: SIZE 0603 TO 2512 STABILITY CLASS 2 OR BETTER RCA e3 1 Ω to 10 MΩ 4.39 - Periodic electric overload U = 15 x P 70 x R ≤ 2 x Umax.; whichever is the less severe; 0.1 s on; 2.5 s off; 1000 cycles ± (1 % R + 0.05 Ω) 4.38 - Electrostatic discharge (human body model) IEC 61340-3-1 (1)(2); 3 pos. + 3 neg. discharges; ESD voltage according to the size ± (1 % R + 0.05 Ω) Vibration Endurance by sweeping; 10 Hz to 2000 Hz; no resonance; amplitude ≤ 1.5 mm or ≤ 200 m/s2; 7.5 h ± (0.25 % R + 0.05 Ω) 4.22 6 (Fc) Solder bath method; Sn60Pb40 non-activated flux; (235 ± 5) °C; (2 ± 0.2) s Good tinning (≥ 95 % covered) no visible damage 4.17 58 (Td) Solderability 4.18 58 (Td) Resistance to soldering heat Solder bath method (260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 Ω) 4.29 45 (XA) Component solvent resistance Isopropyl alcohol; +50 °C; method 2 No visible damage 4.32 21 (Uu3) Shear (adhesion) RCA0402 and RCA0603: 9 N RCA0805 to RCA2512: 17.7 N No visible damage 4.33 21 (Uu1) Substrate bending Depth 2 mm; 3 times ± (0.25 % R + 0.05 Ω) no visible damage, no open circuit in bent position 4.7 - Voltage proof U = 1.4 x Uins; 60 s No flashover or breakdown - Flammability, needle flame test IEC 60695-11-5 (1); 10 s No burning after 30 s 4.35 Solder bath method; Sn96.5Ag3Cu0.5 or Sn99.3Cu0.7 non-activated flux; (245 ± 5) °C or (250 ± 5) °C (3 ± 0.3) s Notes (1) The quoted IEC standards are also released as EN standards with the same number and identical contents (2) This test is new with the 4th edition of IEC 60115-1 and with this European standard, and adopts the prior test of EN 60115-1+A11:2007.4.40 Revision: 04-Jul-2022 Document Number: 20037 8 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCA e3 www.vishay.com Vishay Draloric DIMENSIONS L T2 W H T1 DIMENSIONS AND MASS L (mm) W (mm) H (mm) T1 (mm) RCA0402 e3 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 RCA0603 e3 1.55 + 0.10 / - 0.05 0.85 ± 0.1 0.45 ± 0.05 RCA0805 e3 2.0 + 0.20 / - 0.10 1.25 ± 0.15 RCA1206 e3 3.2 + 0.10 / - 0.20 RCA1210 e3 3.2 ± 0.20 RCA1218 e3 3.2 + 0.10 / - 0.20 RCA2010 e3 RCA2512 e3 TYPE / SIZE T2 (mm) MASS (mg) 0.25 ± 0.10 0.2 ± 0.10 0.65 0.3 ± 0.20 0.3 ± 0.20 2 0.45 ± 0.05 0.3 + 0.20 / -0.10 0.3 ± 0.20 5.5 1.6 ± 0.15 0.55 + 0.05 0.45 ± 0.20 0.4 ± 0.20 10 2.5 ± 0.20 0.55 ± 0.05 0.45 ± 0.20 0.4 ± 0.20 16 4.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.20 0.4 ± 0.20 29.5 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.10 0.6 ± 0.20 0.6 ± 0.20 25.5 6.3 ± 0.20 3.15 ± 0.15 0.6 ± 0.10 0.6 ± 0.20 0.6 ± 0.20 40.5 SOLDER PAD DIMENSIONS X G Y Z RECOMMENDED SOLDER PAD DIMENSIONS WAVE SOLDERING TYPE / SIZE G (mm) Y (mm) X (mm) REFLOW SOLDERING Z (mm) G (mm) Y (mm) X (mm) Z (mm) RCA0402 e3 - - - - 0.45 0.60 0.60 1.65 RCA0603 e3 0.65 1.10 1.25 2.85 0.75 0.75 1.00 2.25 RCA0805 e3 0.90 1.30 1.60 3.50 1.00 0.95 1.45 2.90 RCA1206 e3 1.40 1.40 1.95 4.20 1.50 1.05 1.80 3.60 RCA1210 e3 1.80 1.45 2.95 4.70 1.70 1.10 2.80 3.90 RCA1218 e3 1.80 1.30 5.10 4.40 1.90 1.10 4.90 4.10 RCA2010 e3 3.40 1.65 2.85 6.70 3.50 1.45 2.80 6.40 RCA2512 e3 4.60 1.60 3.65 7.80 4.75 1.45 3.50 7.65 Notes • The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g in standards IEC 61188-5-x (1) or in publication IPC-7351. Still, the given solder pad dimensions will be found adequate for most general applications (1) The quoted IEC standards are also released as EN standards with the same number and identical contents Revision: 04-Jul-2022 Document Number: 20037 9 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000