RCV201010M0FKEF

RCV e3 www.vishay.com Vishay Draloric High Voltage (Up to 2 kV) Thick Film Chip Resistors FEATURES • High operating voltage (up to 2 kV) • Low voltage coefficient of resistance (VCR): 25 ppm/V • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS LINKS TO ADDITIONAL RESOURCES • E-meter 3D 3D • Inverters for industrial drives, aircons, and white good 3D Models • AC power supplies The RCV e3 high voltage thick film chip resistors series are the perfect choice for modern electronics with high voltage requirements. Typical applications include E-meter, AC power supplies, lighting ballasts and inverters for industrial drives, aircons, and white good. • Lighting ballasts TECHNICAL SPECIFICATIONS DESCRIPTION RCV0805 e3 Imperial size Metric size code RCV1206 e3 RCV2010 e3 0805 1206 2010 RR2012M RR3216M RR5025M Resistance range 100 kΩ to 10 MΩ Resistance tolerance ± 5 %; ± 1 % Temperature coefficient ± 200 ppm/K; ± 100 ppm/K Voltage coefficient lcl of resistance chart Rated dissipation, P70 (1) Operating voltage, Umax. ACRMS/DC Permissible film temperature, ϑF max. 25 ppm/V 0.125 W 0.25 W 0.75 W 400 V 500 V 2000 V (1) 155 °C Operating temperature range -55 °C to +155 °C Max. resistance change at P70 for resistance range, |ΔR/R| after: 1000 h ≤ 1.0 % ≤ 1.0 % ≤ 2.0 % Notes • Application-specific safety requirements may set limitations to the applicability of the specified voltage (1) Please refer to APPLICATION INFORMATION below APPLICATION INFORMATION When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted film temperature is not exceeded. These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime. Revision: 13-Jun-2022 Document Number: 20054 1 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCV e3 www.vishay.com Vishay Draloric TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE / SIZE TCR TOLERANCE RESISTANCE E-SERIES ± 200 ppm/K ±5% 100 kΩ to 10 MΩ E24 ± 100 ppm/K ±1% 100 kΩ to 10 MΩ E24; E96 ± 200 ppm/K ±5% 100 kΩ to 10 MΩ E24 ± 100 ppm/K ±1% 100 kΩ to 10 MΩ E24; E96 ± 200 ppm/K ±5% 100 kΩ to 10 MΩ E24 ± 100 ppm/K ±1% 100 kΩ to 10 MΩ E24; E96 RCV0805 e3 RCV1206 e3 RCV2010 e3 PACKAGING TYPE / SIZE RCV0805 e3 RCV1206 e3 RCV2010 e3 PACKAGING STYLE WIDTH PACKAGING DIMENSIONS CODE QUANTITY EA = ET1 5000 Ø 180 mm / 7" EB = ET5 10 000 Ø 285 mm / 11.25" EC = ET6 20 000 Paper tape according to IEC 60286-3, type 1a PITCH Ø 330 mm / 13" 8 mm 4 mm EA = ET1 5000 EB = ET5 10 000 Ø 285 mm / 11.25" EC = ET6 20 000 Ø 330 mm / 13" EF = E02 4000 Blister tape according to IEC 60286-3, type 2a Ø 180 mm / 7" 12 mm 4 mm Ø 180 mm / 7" PART NUMBER AND PRODUCT DESCRIPTION Part Number: RCV1206100KFKEA R C V 1 2 0 6 1 0 0 K F K E A TYPE / SIZE RESISTANCE TOLERANCE TCR PACKAGING RCV0805 RCV1206 RCV2010 K = thousand M = million F=±1% J=±5% K = ± 100 ppm/K N = ± 200 ppm/K EA, EB, EC, EF Product Description: RCV1206 100 100K 1 % ET1 e3 RCV1206 100 100K 1% ET1 e3 TYPE / SIZE TCR RESISTANCE TOLERANCE PACKAGING LEAD (Pb)-FREE RCV0805 RCV1206 RCV2010 ± 100 ppm/K ± 200 ppm/K 100K = 100 kΩ 1M = 1 MΩ 10M = 10 MΩ 100M = 100 MΩ ±1% ±5% ET1, ET5, ET6, E02 e3 = pure tin termination finish Revision: 13-Jun-2022 Document Number: 20054 2 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCV e3 www.vishay.com DESCRIPTION Production is strictly controlled and follows an extensive set of instructions established for reproducibility. A cermet film layer and a glass-over are deposited on a high grade (Al2O3) ceramic substrate. Specially designed inner contacts are deposited on both sides. A special laser is used to achieve the target value by smoothly fine trimming the resistive layer without damaging the ceramics. The resistor elements are covered by a protective coating designed for electrical, mechanical, and climatic protection. The terminations receive a final pure tin on nickel plating. The result of the determined production is verified by an extensive testing procedure on 100 % of the individual chip resistors. Only accepted products are laid directly into the tape in accordance with IEC 60286-3 type 1a and 2a (1). ASSEMBLY The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic soldering using wave, reflow or vapor phase as shown in IEC 61760-1 (1). The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters, and aqueous solutions. The suitability of conformal coatings, potting compounds and their processes, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. The resistors are RoHS-compliant, the pure tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. Solderability is specified for 2 years after production or requalification. The permitted storage time is 20 years. The immunity of the plating against tin whisker growth has been proven under extensive testing. Vishay Draloric Hence the products fully comply with the following directives: • 2000/53/EC End-of-Life Vehicle Directive (ELV) and Annex II (ELV II) • 2011/65/EU Restriction of the Use of Hazardous Substances Directive (RoHS) with amendment 2015/863/EU • 2012/19/EU Waste Electrical and Electronic Equipment Directive (WEEE) Vishay pursues the elimination of conflict minerals from its supply chain, see the Conflict Minerals Policy at www.vishay.com/doc?49037. APPROVALS Where applicable, the resistors are tested in accordance with EN 140401-802 which refers to EN 60115-1, EN 60115-8 and the variety of environmental test procedures of the IEC 60068 (1) series. RELATED PRODUCTS For high voltage thin film products, please refer to latest edition of TNPV e3, High Voltage Thin Film Chip Resistors datasheet, www.vishay.com/doc?28881. For products with professional specification, please refer to latest edition of MMA0204 HV, MMB0207 HV, Professional High Voltage Thin Film MELF Resistors datasheet, www.vishay.com/doc?28880. MATERIALS Vishay acknowledges the following systems for the regulation of hazardous substances: • IEC 62474, Material Declaration for Products of and for the Electrotechnical Industry, with the list of declarable substances given therein (2) • The Global Automotive Declarable Substance List (GADSL) (3) • The REACH regulation (1907/2006/EC) and the related list of substances with very high concern (SVHC) (4) for its supply chain The products do not contain any of the banned substances as per IEC 62474, GADSL, or the SVHC list, see www.vishay.com/how/leadfree. Notes (1) The quoted IEC standards are also released as EN standards with the same number and identical contents (2) The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474 (3) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council and available at www.gadsl.org (4) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table Revision: 13-Jun-2022 Document Number: 20054 3 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCV e3 www.vishay.com Vishay Draloric DERATING Axis Title 10000 RCV2010 0.8 0.6 1000 0.5 1st line 2nd line 2nd line P - Power Dissipation (W) 0.7 0.4 RCV1206 0.3 0.2 100 RCV0805 0.1 10 0 -70 -50 -30 -10 10 30 50 70 90 110 130 150 ϑamb - Ambient Temperature (°C) NOMINAL OPERATING VOLTAGE Axis Title 2200 10000 RCV2010 1800 1600 1000 1400 1st line 2nd line 2nd line Permissible Operating Voltage (V) 2000 1200 1000 800 100 RCV1206 600 400 RCV0805 200 0 100 000 1 000 000 10 10 000 000 Resistance Value (Ω) The permissible operating voltage Umax. equals the rated voltage. For ambient temperatures above 70 °C power derating must be considered TESTS AND REQUIREMENTS All executed tests are carried out in accordance with the following specifications: EN 60115-1, generic specification EN 60115-8 specification (successor of EN 140400), sectional The tests are carried out under standard atmospheric conditions in accordance with IEC 60068-1, 4.3, whereupon the following values are applied: Temperature: 15 °C to 35 °C Relative humidity: 25 % to 75 % EN 140401-802, detail specification Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar) IEC 60068-2-xx, test methods A climatic category LCT / UCT / 56 is applied, defined by the lower category temperature (LCT), the upper category temperature (UCT), and the duration of exposure in the damp heat, steady state test (56 days). The parameters stated in the “Test Procedures and Requirements” table are based on the required tests and permitted limits of EN 140401-802. The table presents only the most important tests, for the full test schedule refer to the documents listed above. However, some additional tests and a number of improvements against those minimum requirements have been included. The testing also covers most of the requirements specified by EIA/IS-703 and JIS-C-5201-1. Revision: 13-Jun-2022 Document Number: 20054 4 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCV e3 www.vishay.com Vishay Draloric TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60082-2 (1) TEST METHOD REQUIREMENTS PERMISSIBLE CHANGE (ΔR) PROCEDURE STABILITY CLASS 1 OR BETTER TEST Stability for product types: RCV e3 4.5 - STABILITY CLASS 2 OR BETTER 100 kΩ to 10 MΩ Resistance - ±1% ±5% ± 100 ppm/K ± 200 ppm/K 4.8 - Temperature coefficient At (20 / -55 / 20) °C and (20 / 155 / 20) °C 4.25.1 - Endurance at 70 °C U = P 70 x R or U = Umax. whichever is the less severe; 1.5 h on; 0.5 h off 70 °C; 1000 h RCV0805, RCV1206: ± (1 % R + 0.05 Ω) RCV2010: ± (2 % R + 0.1 Ω) 4.25.3 - Endurance at upper category temperature 155 °C; 1000 h ± (2 % R + 0.1 Ω) 78 (Cab) Damp heat, steady state (40 ± 2) °C; 56 days; (93 ± 3) % RH - Climatic sequence: 4.24 4.23 4.23.2 2 (Bb) Dry heat 125 °C; 16 h 4.23.3 30 (Db) Damp heat, cyclic 55 °C; 24 h; ≥ 90 % RH; 1 cycle ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) ± (1 % R + 0.05 Ω) ± (2 % R + 0.1 Ω) 4.23.4 1 (Ab) Cold -55 °C: 2 h 4.23.5 13 (M) Low air pressure 8.5 kPa; 2 h; (25 ± 10) °C 4.23.6 30 (Db) Damp heat, cyclic 55 °C; 5 days; > 90 % RH; 5 cycles 4.23.7 - DC load U = P 70 x R ≤ Umax.; 1 min 1 (Aa) Cold -55 °C; 2 h ± (0.5 % R + 0.05 Ω) Rapid change of temperature 30 min. at -55 °C and 30 min. at 125 °C; RCV0805, RCV1206: 1000 cycles RCV2010: 100 cycles ± (1 % R + 0.05 Ω) no visible damage 4.19 14 (Na) U = 2.5 x P 70 x R ≤ 2 x Umax.; whichever is the less severe; 5 s 4.13 - Short time overload Style Duration Maximum UOL RCV0805 1s 800 RCV1206 2s 1000 RCV2010 5s 3000 RCV0805, RCV1206: ± (0.25 % R + 0.05 Ω) RCV2010: ± (2.0 % R + 0.05 Ω) Severity no. 4: U = 10 x P 70 x R or U = 2 x Umax.; whichever is the less severe; 10 pulses ± (2 % R + 0.1 Ω) no visible damage 4.27 - Single pulse high voltage overload 10 μs / 700 μs 4.39 - Periodic electric overload U = 15 x P 70 x R or U = 2 x Umax.; whichever is the less severe; 0.1 s on; 2.5 s off; 1000 cycles ± (2 % R + 0.05 Ω) no visible damage ± (1 % R + 0.05 Ω) ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) no visible damage no visible damage 4.38 - Electrostatic discharge (human body model) IEC 61340-3-1 (1); 3 positive + 3 negative discharges; RCV0805: 1000 V RCV1206: 2000 V RCV2010: 12 kV 4.22 6 (Fc) Vibration Endurance by sweeping f = 10 Hz to 2000 Hz; no resonance; A ≤ 1.5 mm ≤ 200 m/s2; 7.5 h Solder bath method, SnPb40; non-activated flux (235 ± 5) °C; (2 ± 0.2) s Good tinning (≥ 95 % covered); no visible damage 4.17 58 (Td) Solderability 4.18 58 (Td) Resistance to soldering heat Soldering bath method; (260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω) 4.29 45 (XA) Component solvent resistance Isopropyl alcohol; +50 °C; method 2 No visible damage Revision: 13-Jun-2022 Solder bath method, Sn96.5Ag3Cu0.5; non-activated flux (245 ± 5) °C; (3 ± 0.3) s Document Number: 20054 5 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 RCV e3 www.vishay.com Vishay Draloric TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60082-2 (1) TEST METHOD REQUIREMENTS PERMISSIBLE CHANGE (ΔR) PROCEDURE STABILITY CLASS 1 OR BETTER TEST Stability for product types: 100 kΩ to 10 MΩ RCV e3 4.32 21 (Uu3) Shear (adhesion) STABILITY CLASS 2 OR BETTER 17.7 N No visible damage 4.33 21 (Uu1) Substrate bending Depth 2 mm; 3 times RCV0805, RCV1206: ± (0.25 % R + 0.05 Ω) RCV2010: ± (1 % R + 0.05 Ω) no visible damage, no open circuit in bent position 4.7 - Voltage proof U = 1.4 x Uins; 60 s No flashover or breakdown - Flammability, needle flame test IEC 60695-11-5 (1); 10 s No burning after 30 s 4.35 Note (1) The quoted IEC standards are also released as EN standards with the same number and identical contents DIMENSIONS L T2 W H T1 DIMENSIONS AND MASS TYPE / SIZE L (mm) W (mm) H (mm) T1 (mm) T2 (mm) MASS (mg) RCV0805 e3 2.0 + 0.20 / - 0.10 1.25 ± 0.15 0.45 ± 0.05 0.3 + 0.20 / - 0.10 0.3 ± 0.20 5.5 RCV1206 e3 3.2 + 0.10 / - 0.20 1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.20 0.4 ± 0.20 10 RCV2010 e3 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.10 0.6 ± 0.20 0.45 ± 0.20 25.5 G X SOLDER PAD DIMENSIONS Y Z RECOMMENDED SOLDER PAD DIMENSIONS WAVE SOLDERING REFLOW SOLDERING TYPE / SIZE G (mm) Y (mm) X (mm) Z (mm) G (mm) Y (mm) X (mm) Z (mm) RCV0805 e3 0.90 1.30 1.60 3.50 1.00 0.95 1.45 2.90 RCV1206 e3 1.40 1.40 1.95 4.20 1.50 1.05 1.80 3.60 RCV2010 e3 3.60 1.65 2.85 6.90 3.70 1.20 2.70 6.10 Note • Utilization of the full specified operating voltage may require special considerations on the creepage and clearance distance between conductors at different potential levels Revision: 13-Jun-2022 Document Number: 20054 6 For technical questions, contact: thickfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000