SFH6206AGB

SFH620AA, SFH620AGB www.vishay.com Vishay Semiconductors Optocoupler, Phototransistor Output, AC Input, 5300 VRMS FEATURES A/C 1 4 C C/A 2 3 E • High current transfer ratios - at 5 mA: 50 to 600 % - at 1.0 mA: 45 % typical (> 13) • Low CTR degradation • Good CTR linearity depending on forward current • Isolation test voltage, 5300 VRMS • High collector emitter voltage, VCEO = 70 V • Low saturation voltage • Fast switching times • Temperature stable • Low coupling capacitance • End stackable, 0.100" (2.54 mm) spacing • High common mode interference immunity (unconnected base) • SMD option, see SFH620A, SFH6206 datasheet • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 i179062-1 DESCRIPTION The SFH620AA, SFH620AGB features a high current transfer ratio, low coupling capacitance and high isolation voltage. These couplers have a GaAs infrared emitting diode emitter, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a plastic DIP-4 package. The coupling devices are designed for signal transmission between two electrically separated circuits. The couplers are end-stackable with 2.54 mm lead spacing. This version complies with IEC 60950 (DIN VDE 0805) for reinforced insulation up to an operation voltage of 400 VRMS or DC. AGENCY APPROVALS • • • • UL1577, file no. E52744 system code H, double protection CSA 93751 BSI IEC 60950; IEC 60065 VDE 0884-5, DIN EN 60747-5-5, available with option 1 ORDERING INFORMATION S F H 6 2 0 A x x - PART NUMBER X 0 0 DIP-4 1 PACKAGE OPTION 7.62 mm CTR (%) AGENCY CERTIFIED/PACKAGE UL, CSA, BSI DIP-4 VDE, UL, CSA, BSI ± 5 mA 50 to 600 100 to 600 SFH620AA SFH620AGB 50 to 600 100 to 600 - SFH620AGB-X001 DIP-4 ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT tp 1.0 μs IF ± 60 mA IFSM ± 2.5 A Pdiss 100 mW Collector emitter voltage VCE 70 V Emitter collector voltage VEC 7 V INPUT DC forward current Surge forward current Total power dissipation OUTPUT Collector current Power dissipation Rev. 1.8, 19-Nov-14 tp 1.0 ms IC 50 mA IC 100 mA Pdiss 150 mW Document Number: 83676 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620AA, SFH620AGB www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT VISO 5300 VRMS Creepage distance 7 mm Clearance distance 7 mm 0.4 mm COUPLER Isolation test voltage between emitter and detector Insulation thickness between emitter and detector Comparative tracking index per  DIN IEC 112/VDE 0303 part 1 Isolation resistance VIO = 500 V, Tamb = 25 °C CTI 175 RIO 1012   RIO 1011 Storage temperature Tstg -55 to +150 °C Ambient temperature Tamb -55 to +100 °C Junction temperature Tj 100 °C Tsld 260 °C Soldering temperature (1) VIO = 500 V, Tamb = 100 °C max. 10 s, dip soldering distance to seating plane  1.5 mm Notes • Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP). ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. 1.65 UNIT INPUT Forward voltage Capacitance IF = ± 60 mA VF 1.25 VR = 0 V, f = 1 MHz CO 50 pF Rthja 750 K/W Thermal resistance V OUTPUT Collector emitter capacitance VCE = 5 V, f = 1 MHz CCE 6.8 pF Rthja 500 K/W VCEsat 0.25 CC 0.2 SFH620AA ICEO 10 100 nA SFH620AGB ICEO 10 100 nA Thermal resistance COUPLER Collector emitter saturation voltage IF = ± 10 mA, IC = 2.5 mA Coupling capacitance Collector emitter leakage current VCE = 10 V 0.4 V pF Note • Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. CURRENT TRANSFER RATIO (Tamb = 25 °C, unless otherwise specified) PARAMETER IC/IF Rev. 1.8, 19-Nov-14 TEST CONDITION IF = ± 5 mA, VCE = 5 V PART SFH620AA SFH620AGB SYMBOL CTR MIN. TYP. MAX. UNIT 50 600 % 100 600 % Document Number: 83676 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620AA, SFH620AGB www.vishay.com Vishay Semiconductors R L = 1.9 Ω I F = 5 mA VCC = 5 V IC 47 Ω isfh620aa_0 Fig. 1 - Switching Times (Typical Values) Linear Operation (Saturated) SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL Turn-on time IF = ± 5 mA, RL = 1.9 k, VCC = 5 V ton MIN. TYP. 2 MAX. UNIT μs Turn-off time IF = ± 5 mA, RL = 1.9 k, VCC = 5 V toff 25 μs SAFETY AND INSULATION RATINGS PARAMETER TEST CONDITION SYMBOL MIN. Climatic classification (according to IEC 68 part 1) TYP. MAX. UNIT 55/100/21 Comparative tracking index CTI 175 VIOTM 10000 VIORM 890 399 V V PSO 400 mW ISI 275 mA TSI 175 °C Creepage distance standard DIP-4 7 mm Clearance distance standard DIP-4 7 mm per IEC 60950 2.10.5.1 0.4 mm Insulation thickness, reinforced rated Note • As per IEC 60747-5-5, this optocoupler is suitable for “safe electrical insulation” only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 30 103 IF = 14 mA IC (%) IF IF = 10 mA, VCC = 5 V IC (mA) IF = 12 mA 3 2 102 20 IF = 10 mA IF = 8 mA 1 IF = 6 mA 10 IF = 4 mA IF = 1 mA 101 - 25 isfh620a_01 0 0 25 TA (°C) 50 75 Fig. 2 - Current Transfer Ratio (CTR) vs. Temperature Rev. 1.8, 19-Nov-14 0 isfh620a_02 5 IF = 2 mA 10 VCE (V) 15 Fig. 3 - Output Characteristics (Typ.) Collector Current vs. Collector Emitter Voltage Document Number: 83676 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620AA, SFH620AGB www.vishay.com Vishay Semiconductors 1.2 200 VF = f (IF) Ptot (mW) VF (V) 25 °C 50 °C 75 °C 1.1 150 Transistor 100 1.0 Diode 50 0.9 10-1 100 101 IF (mA) isfh620a_03 0 102 0 25 50 Fig. 4 - Diode Forward Voltage (Typ.) vs. Forward Current 75 100 TA (°C) isfh620a_06 Fig. 7 - Permissible Power Dissipation vs. Ambient Temperature 120 Ptot = f (TA) 20 f = 1 MHz 90 IF (mA) C (pF) 15 60 10 30 5 CCE 0 0 0 10-2 10-1 100 101 Ve (V) isfh620a_04 102 Fig. 5 - Transistor Capacitance (Typ.) vs. Collector Emitter Voltage IF (mA) 104 103 D=0 0.005 0.01 0.02 D= tp T 0.05 0.1 tp isfh620a_07 25 50 75 100 TA (°C) Fig. 8 - Permissible Diode Forward Current vs. Ambient Temperature IF T Pulse cycle D = parameter 0.2 102 0.5 DC 101 10-5 isfh620a_05 10-4 10-3 10-2 10-1 tp (s) 100 101 Fig. 6 - Permissible Pulse Handling Capability Forward Current vs. Pulse Width Rev. 1.8, 19-Nov-14 Document Number: 83676 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 SFH620AA, SFH620AGB www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 6.48 6.81 Pin 1 identification 4.55 4.83 ISO method A 0.76 7.62 typ. 0.79 typ. 1.14 1.27 typ. 3.30 3.81 5.84 6.35 10° 4° typ. 2.79 3.30 0.508 0.89 0.46 0.56 0° to 15° 0.2 0.3 1.27 2.54 i178027-8 PACKAGE MARKING (example of SFH620AGB-X001) YWW H 68 SFH620AGB V X001 Note • The VDE logo is only marked on option1 parts. Rev. 1.8, 19-Nov-14 Document Number: 83676 5 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000