TSOP13140

Datasheet Values Refer to PCN-OPT-1225-2022-REV-HS1 TSOP131.., TSOP133.., TSOP135.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems DESCRIPTION This IR receiver series is optimized for short burst remote control systems in different environments. The customer can chose between different IC settings (AGC variants), to find the optimum solution for his application. The higher the AGC, the better noise is suppressed, but the lower the code compatibility. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. These components have not been qualified to automotive specifications. 23051 FEATURES • Individual IC settings to reach maximum performance • Immunity against noise (lamps, LCD TV, Wi-Fi) • Low supply current • Photo detector and preamplifier in one package • Supply voltage: 2.0 V to 5.5 V • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 LINKS TO ADDITIONAL RESOURCES Product Page Marking Packages Holders Bends and Cuts DESIGN SUPPORT TOOLS • 3D models • Window size calculator APPLICATIONS • Infrared remote control systems BLOCK DIAGRAM VS 30 kΩ OUT Input AGC Band pass Demodulator GND PIN Control circuit 16833-22 Rev. 1.7, 28-Sep-2022 1 Document Number: 82805 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1225-2022-REV-HS1 TSOP131.., TSOP133.., TSOP135.. www.vishay.com Vishay Semiconductors MECHANICAL DATA ORDERING CODE Pinning for TSOP13...: 1 = OUT, 2 = GND, 3 = VS TSOP13... - 1800 pieces in bags APPLICATION CIRCUIT 17170-14 R1 IR receiver VS + VS C1 Circuit Transmitter with TSALxxxx µC OUT 1 VO GND 2 3 GND 23197 R1 and C1 recommended in case there are strong ripple or spikes on the supply line. PARTS TABLE BASIC NOISE SUPPRESSION (AGC1) ENHANCED NOISE SUPPRESSION (AGC3) MAXIMIZED NOISE SUPPRESSION (AGC5) 30 kHz TSOP13130 TSOP13330 TSOP13530 33 kHz TSOP13133 TSOP13333 TSOP13533 AGC Carrier frequency (1)(5) TSOP13536 TSOP13538 36 kHz TSOP13136 TSOP13336 38 kHz TSOP13138 TSOP13338 (2)(4) 40 kHz TSOP13140 TSOP13340 TSOP13540 56 kHz TSOP13156 TSOP13356 (3) TSOP13556 Package Minimold Pinning 1 = OUT, 2 = GND, 3 = VS Dimensions (mm) 5.4 W x 6.35 H x 4.9 D Mounting Leaded Application Remote control (1) Best choice for Special options RCMM (2) RECS-80 Code (3) r-map (4) XMP (5 MCIR • Narrow optical filter: www.vishay.com/doc?81590 • Wide optical filter: www.vishay.com/doc?82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION Supply voltage SYMBOL VALUE UNIT VS -0.3 to +6 V mA Supply current IS 3 Output voltage VO -0.3 to (VS + 0.3) V Output current IO 5 mA Junction temperature Tj 100 °C Storage temperature range Tstg -25 to +85 °C Operating temperature range Tamb -25 to +85 °C Tamb ≤ 85 °C Ptot 10 mW t ≤ 10 s, 1 mm from case Tsd 260 °C Power consumption Soldering temperature Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability Rev. 1.7, 28-Sep-2022 2 Document Number: 82805 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1225-2022-REV-HS1 TSOP131.., TSOP133.., TSOP135.. www.vishay.com Vishay Semiconductors ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Ev = 0, VS = 3.3 V ISD 0.25 0.35 0.45 mA Ev = 40 klx, sunlight ISH - 0.45 - mA VS 2.0 - 5.5 V Transmission distance Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA d - 39 - m Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 VOSL - - 100 mV Test signal: RC5 code Ee min. - 0.05 0.1 mW/m2 Test signal: XMP code Ee min. - 0.1 0.2 mW/m2 tpi - 3.0/f0 < tpo < tpi + 3.5/f0, test signal see Fig. 1 Ee max. 30 - - W/m2 Angle of half transmission distance ϕ1/2 - ± 45 - ° Supply current Supply voltage Minimum irradiance Maximum irradiance Directivity TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Ee Optical Test Signal (IR diode TSAL6200, N = 6 pulses, f = f0, T = 10 ms) Optical Test Signal Ee t tpi (1) 600 µs t 600 µs T t = 60 ms tpi ≥ 6/f0 Output Signal VO (2) (3) VOH VOL 4/f0 < td < 10/f0 tpi - 3.0/f0 < tpo < tpi + 3.5/f0 td (2) VOH VOL t tpo (3) t on 14337-5 Fig. 1 - Output Delay and Pulse-Width Axis Title 10000 2nd line ton, toff - Output Pulse Width (ms) 1000 1st line 2nd line 2nd line tpo - Output Pulse Width (ms) 0.25 0.20 Input burst length 100 0.10 λ = 950 nm, optical test signal, Fig. 1 0 0.1 10 1000 10000 0.8 Output pulse width 0.05 t t off Fig. 3 - Test Signal Axis Title 0.30 0.15 94 8134 Output Signal, (see Fig. 4) VO 10 100 000 ton 0.7 0.6 1000 0.5 toff 1st line 2nd line (1) 0.4 0.3 100 0.2 0.1 λ = 950 nm, optical test signal, Fig. 3 0 0.1 1 10 100 1000 10 10 000 Ee - Irradiance (mW/m2) Ee - Irradiance (mW/m2) Fig. 2 - Pulse-Width vs. Irradiance in Dark Ambient Fig. 4 - Pulse-Width vs. Irradiance in Dark Ambient Rev. 1.7, 28-Sep-2022 3 Document Number: 82805 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1225-2022-REV-HS1 TSOP131.., TSOP133.., TSOP135.. www.vishay.com Vishay Semiconductors Axis Title Axis Title 1.0 10000 1.2 10000 f = 38 kHz, Ee = 2 mW/m2 AGC3, AGC5 AGC1 0.6 100 0.4 f = f0 ± 5 % 0.2 AGC1: ∆f (3 dB) = f0/7 AGC3, AGC5: ∆f (3 dB) = f0/10 0.9 1.1 0.7 0.5 0.4 0.3 AGC5 10 0 0 20 40 60 80 100 120 140 f/f0 - Relative Frequency Burst Length (Number of Cycles/Burst) Fig. 5 - Frequency Dependence of Responsivity Fig. 8 - Maximum Envelope Duty Cycle vs. Burst Length Axis Title Axis Title 2nd line Ee min. - Threshold Irradiance (mW/m2) Correlation with ambient light sources: 10 W/m2 = 1.4 klx (std. ilum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) 1.5 Wavelength of ambient illumination: λ = 950 nm 1000 1 100 0.5 0 0.01 10 0.1 1 10 0.3 10000 0.2 1000 0.1 100 1st line 2nd line 10000 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 100 AGC 3 0.2 1.3 2 10 0 -30 100 -10 10 30 50 70 90 Ee - Ambient DC Irradiance (W/m2) Tamb - Ambient Temperature (°C) Fig. 6 - Sensitivity in Bright Ambient Fig. 9 - Sensitivity vs. Ambient Temperature Axis Title Axis Title 10000 1.0 0.7 0.6 1000 0.5 1st line 2nd line f = f0 f = 30 kHz 0.4 f = 10 kHz f = 100 Hz 0.3 100 0.2 0.1 0 1 10 100 10000 0.9 0.8 0.7 1000 0.6 1st line 2nd line 2nd line S(λ)rel. - Relative Spectral Sensitivity 0.8 2nd line Ee min. - Threshold Irradiance (mW/m2) 1000 AGC1 0.6 0.1 10 0 0.7 0.8 1st line 2nd line 2nd line Maximum Envelope Duty Cycle 1000 0.8 1st line 2nd line 2nd line Ee min./Ee - Relative Responsivity 0.9 1.0 0.5 0.4 100 0.3 0.2 0.1 0 10 1000 750 850 950 1050 10 1150 ∆VS RMS - AC Voltage on DC Supply Voltage (mV) λ - Wavelength (nm) Fig. 7 - Sensitivity vs. Supply Voltage Disturbances Fig. 10 - Relative Spectral Sensitivity vs. Wavelength Rev. 1.7, 28-Sep-2022 4 Document Number: 82805 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1225-2022-REV-HS1 TSOP131.., TSOP133.., TSOP135.. www.vishay.com Axis0° Title 10° Vishay Semiconductors 20° Axis Title 30° 50° 0.8 60° 70° 0.7 80° 10000 0.3 1000 1st line 2nd line 0.9 2nd line 2nd line 40° 1.0 2nd line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 0.4 0.2 100 0.1 10 0 0.6 0.4 0.2 0 0.2 0.4 1 0.6 2 3 4 5 drel. - Relative Transmission Distance VS - Supply Voltage (V) Fig. 11 - Directivity Fig. 12 - Sensitivity vs. Supply Voltage Rev. 1.7, 28-Sep-2022 5 6 Document Number: 82805 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1225-2022-REV-HS1 TSOP131.., TSOP133.., TSOP135.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver’s output. Some examples which are suppressed are: • DC light (e.g. from tungsten bulbs sunlight) • Continuous signals at any frequency • Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 13 or Fig. 14). • 2.4 GHz and 5 GHz Wi-Fi 10000 7 5 1000 1st line 2nd line 2nd line IR Signal Amplitude 6 4 3 100 2 1 10 0 0 5 10 15 20 Time (ms) 16920 Fig. 13 - IR Emission from Fluorescent Lamp With Low Modulation Axis Title 10000 40 1000 0 1st line 2nd line 2nd line IR Signal Amplitude 20 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 14 - IR Emission from Fluorescent Lamp With High Modulation TSOP131.. TSOP133.. TSOP135.. Minimum burst length 6 cycles/burst 6 cycles/burst 6 cycles/burst After each burst of length A gap time is required of 6 to 68 cycles ≥ 7 cycles 6 to 36 cycles ≥ 8 cycles 6 to 19 cycles ≥ 8 cycles 68 cycles 36 cycles 19 cycles For bursts greater than a minimum gap time in the data stream is needed of > 1 x burst length > 10 x burst length > 10 x burst length Maximum number of continuous short bursts/second 2100 2100 2100 RCMM code Yes Preferred Yes XMP code Yes Preferred Yes r-map code Yes Preferred Yes Fig. 13 Fig. 13 and Fig. 14 Fig. 13 and Fig. 14 Suppression of interference from fluorescent lamps Note • For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP132.., TSOP134.., TSOP136.. Rev. 1.7, 28-Sep-2022 6 Document Number: 82805 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1225-2022-REV-HS1 TSOP131.., TSOP133.., TSOP135.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 5 Cavity number Marking area 5.4 R2.5 15.2 ± 0.3 (0.95) (5.05) 7.6 6.35 2.25 (1.1) (3 x) 0.85 max. 0.95 1 2 3 (3 x) 0.6 ± 0.1 (3 x) 0.3 ± 0.1 2.54 nom. 2.54 nom. Technical drawings according to DIN specifications R2.5 Not indicated tolerances ± 0.2 Drawing-No.: 6.550-5335.01-4 Issue: 2; 02.07.19 Rev. 1.7, 28-Sep-2022 7 Document Number: 82805 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1225-2022-REV-HS1 TSOP131.., TSOP133.., TSOP135.. www.vishay.com Vishay Semiconductors BULK PACKAGING Standard shipping for minimold is in conductive plastic bags. The packing quantity is determined by weight and the number of components per carton may vary by a maximum of ± 0.3 %. ORDERING INFORMATION Examples: TSOP13338 TSOP13356VI1 TSOP13338SS1F For more information, see: www.vishay.com/doc?80076 PACKAGING QUANTITY • 300 pieces per bag (each bag is individually boxed) • 6 bags per carton Rev. 1.7, 28-Sep-2022 8 Document Number: 82805 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000