VR37000001205JR500

VR25, VR37, VR68 www.vishay.com Vishay BCcomponents High Ohmic / High Voltage Metal Glaze Leaded Resistors FEATURES • UL approved (UL1676, file no: E171160) • Meet the safety requirements of: - IEC 62368-1 - CQC (China) • AEC-Q200 qualified (VR25, VR37) • High pulse loading capability (maximum 10 kV) • Radial version available for VR25 • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS LINKS TO ADDITIONAL RESOURCES • Where high resistance, high stability, and high reliability at high voltage are required 3D 3D 3D Models • High humidity environment A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to the end-caps. The resistors are coated with a light blue lacquer which provides electrical, mechanical, and climatic protection. This coating is not resistant to aggressive fluxes and cleaning solvents. The encapsulation is resistant to all cleaning solvents in accordance with IEC 60068-2-45. • White goods • Power supplies • Automotive electronics TECHNICAL SPECIFICATIONS DESCRIPTION DIN size Resistance range (1) Resistance tolerance Temperature coefficient Rated dissipation, P70 Operating voltage, Umax. ACRMS/DC Operating temperature range Permissible film temperature Thermal resistance (Rth) Insulation voltage: 1 min.; Uins Maximum noise (white noise) Max. resistance change at rated dissipation for resistance range, |ΔR/R| max., after 1000 h VR25 0207 100 kΩ to 22 MΩ 140 K/W VR37 0309 100 kΩ to 33 MΩ ± 10 %; ± 5 %; ± 1 % ≤ ± 200 ppm/K 0.5 W 3500 V -55 °C to +155 °C 155 °C 120 K/W 5 μV/V 700 V 2.5 μV/V 2.5 μV/V 1.5 % 1.5 % 1.5 % 0.25 W 1600 V VR68 0718 100 kΩ to 68 MΩ 1.0 W 10 000 V 70 K/W Note (1) Ohmic values (other than resistance range) are available on request SAFETY REQUIREMENTS AND QUALIFICATIONS DESCRIPTION Safety requirements / qualifications Revision: 02-Jun-2022 VR25, VR37 AEC-Q200 VR37 VR68 UL1676 qualification (file no: E171160) for ohmic range 510 kΩ to 11 MΩ; IEC 62368-1; CQC Document Number: 28907 1 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VR25, VR37, VR68 www.vishay.com Vishay BCcomponents TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE TCR TOLERANCE RESISTANCE E-SERIES ±1% 100 kΩ to 15 MΩ E24; E96 E24; E96 VR25 ±5% 100 kΩ to 22 MΩ ± 10 % 15 MΩ to 22 MΩ E24 ±1% 100 kΩ to 33 MΩ E24; E96 ±5% 100 kΩ to 33 MΩ E24 ±1% 100 kΩ to 68 MΩ E24; E96 ±5% 100 kΩ to 68 MΩ E24 ≤ ± 200 ppm/K VR37 VR68 PACKAGING TYPE CODE QUANTITY VR25 VR37 VR68 WIDTH PITCH 53 mm 5 mm 75 mm x 31 mm x 260 mm 53 mm 5 mm 76 mm x 105 mm x 265 mm Taped according to IEC 60286-2 fan-folded in a box - 12.7 mm 48 mm x 253 mm x 330 mm Taped according to IEC 60286-1 on a reel 53 mm 5 mm 93 mm x 300 mm x 298 mm 1000 Taped according to IEC 60286-1 fan-folded in a box 53 mm 5 mm 72 mm x 60 mm x 258 mm R5 5000 Taped according to IEC 60286-1 on a reel 53 mm 5 mm 90 mm x 375 mm x 375 mm AC 500 Taped according to IEC 60286-1 fan-folded in a box 66 mm 10 mm 82 mm x 111 mm x 256 mm RD 750 Taped according to IEC 60286-1 on a reel 66 mm 10 mm 105 mm x 315 mm x 305 mm A1 1000 A5 5000 N4 4000 R5 5000 A1 PACKAGING STYLE Taped according to IEC 60286-1 fan-folded in a box PACKAGING DIMENSIONS PART NUMBER AND PRODUCT DESCRIPTION PART NUMBER: VR25000001003FA100 V R 2 5 0 0 0 0 0 1 0 0 3 F A 1 0 0 TYPE / SIZE VARIANT TCR RESISTANCE TOLERANCE (1) PACKAGING SPECIAL VR25000 = VR25 VR37000 = VR37 VR68000 = VR68 0 = neutral 0 = standard 3 digit value 1 digit multiplier MULTIPLIER 3 = *103 4 = *104 5 = *105 F=±1% J=±5% K = ± 10 % A1 AC A5 RD R5 N4 00 = standard PRODUCT DESCRIPTION: VR25 1 % A1 100K VR25 1% A1 100K TYPE / SIZE TOLERANCE PACKAGING RESISTANCE VR25 VR37 VR68 ±1% ±5% ± 10 % A1 AC A5 RD R5 N4 100K = 100 kΩ 15M = 15 MΩ Note (1) See table “Temperature Coefficient and Resistance Range” for selecting correct ohmic value - tolerance combination Revision: 02-Jun-2022 Document Number: 28907 2 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VR25, VR37, VR68 www.vishay.com DESCRIPTION Production is strictly controlled and follows an extensive set of instructions established for reproducibility. A homogeneous film of metal glaze is deposited on a high grade ceramic body and conditioned to achieve the desired temperature coefficient. Plated steel termination caps are firmly pressed on the metalized rods. Mostly, a special laser is used to achieve the target value by smoothly cutting a helical groove in the resistive layer without damaging the ceramics. Connecting wires of electrolytic copper plated with 100 % pure matte tin are welded to the termination caps. The resistor elements are covered by a light blue protective coating designed for electrical, mechanical, and climatic protection. Four or five color code rings designate the resistance value and tolerance in accordance with IEC 60062. Yellow and gray are used instead of gold and silver because metal particles in the lacquer could affect high-voltage properties. The result of the determined production is verified by an extensive testing procedure performed on 100 % of the individual resistors. Only accepted products are stuck directly on the adhesive tapes in accordance with IEC 60286-1 or for the radial versions in accordance with IEC 60286-2. MATERIALS Vishay acknowledges the following systems for the regulation of hazardous substances: Vishay BCcomponents Hence the products fully comply with the following directives: • 2000/53/EC End-of-Life Vehicle Directive (ELV) and Annex II (ELV II) • 2011/65/EU Restriction of the Use of Hazardous Substances Directive (RoHS) with amendment 2015/863/EU • 2012/19/EU Waste Electrical and Electronic Equipment Directive (WEEE) Vishay pursues the elimination of conflict minerals from its supply chain, see the Conflict Minerals Policy at www.vishay.com/doc?49037. ASSEMBLY The resistors are suitable for processing on automatic insertion equipment and cutting and bending machines. Excellent solderability is proven, even after extended storage. They are suitable for automatic soldering using wave or dipping. The resistors are completely lead (Pb)-free, the pure matte tin plating provides compatibility with lead (Pb)-free and lead-containing soldering processes. The immunity of the plating against tin whisker growth, in compliance with IEC 60068-2-82, has been proven under extensive testing. The encapsulant is resistant to cleaning solvent specified in IEC 60115-1. The suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. • IEC 62474, Material Declaration for Products of and for the Electrotechnical Industry, with the list of declarable substances given therein (1) APPROVALS • The Global Automotive Declarable Substance List (GADSL) (2) • UL1676 (510 kΩ to 11 MΩ); file no: E171160 • The REACH regulation (1907/2006/EC) and the related list of substances with very high concern (SVHC) (3) for its supply chain • CQC, China The products do not contain any of the banned substances as per IEC 62474, GADSL, or the SVHC list, see www.vishay.com/how/leadfree. These resistors meet the safety requirements of: • IEC 62368-1 RELATED PRODUCTS For a correlated range of Metal Film Resistors see the datasheet: “High Ohmic / High Voltage Metal Film Leaded Resistors”, www.vishay.com/doc?30260 For product that offers high power dissipation and metal oxide film technology see the datasheet: “High Power Metal Oxide Leaded Resistors”, www.vishay.com/doc?20128 Notes (1) The IEC 62474 list of declarable substances is maintained in a dedicated database, which is available at http://std.iec.ch/iec62474 (2) The Global Automotive Declarable Substance List (GADSL) is maintained by the American Chemistry Council, and available at www.gadsl.org (3) The SVHC list is maintained by the European Chemical Agency (ECHA) and available at http://echa.europa.eu/candidate-list-table Revision: 02-Jun-2022 Document Number: 28907 3 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VR25, VR37, VR68 www.vishay.com Vishay BCcomponents FUNCTIONAL PERFORMANCE Power in % Derating 100 80 60 40 20 0 -55 0 50 100 70 125 155 Ambient Temperature in °C Hot-Spot Temperature Rise (ΔT) as a Function of Dissipated Power ΔT (K) 35 ΔT (K) 30 60 50 25 40 20 30 15 20 10 10 5 0 0 0.05 0.10 0.15 0.20 P (W) 0 0.25 0.1 0 VR25 0.2 0.3 0.4 P (W) 0.5 VR37 ΔT (K) 70 60 50 40 30 20 10 0 0 0.2 0.4 0.6 0.8 P (W) 1.0 VR68 Revision: 02-Jun-2022 Document Number: 28907 4 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VR25, VR37, VR68 www.vishay.com Vishay BCcomponents Maximum allowed peak pulse voltage in accordance with IEC 62368-1, G.10); 50 discharges from a 1 nF capacitor charged to Ûmax.; 12 discharges/min (drift ΔR/R ≤ 2 %) Ûmax. (kV) 8 7 6 5 4 -2 10 10-1 1 Rn (MΩ) 10 102 10 102 10 102 VR25 11 Ûmax. (kV) 10 9 8 7 6 5 4 -2 10 10-1 1 Rn (MΩ) VR37 11 Ûmax. (kV) 10 9 8 7 6 5 4 -2 10 10-1 1 Rn (MΩ) VR68 Revision: 02-Jun-2022 Document Number: 28907 5 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VR25, VR37, VR68 www.vishay.com Vishay BCcomponents Temperature Rise (ΔT) at the Lead End (Soldering Point) as a Function of Dissipated Power at Various Lead Lengths after Mounting ΔT (K) 35 30 5 mm 10 mm 25 15 mm 20 15 10 5 0 0 0.025 0.05 0.075 0.10 0.125 P (W) 0.15 0.175 0.20 0.225 0.25 VR25 ΔT (K) 40 35 30 5 mm 10 mm 15 mm 25 20 15 10 5 0 0 0.1 0.2 0.3 0.4 0.5 P (W) VR37 ΔT (K) 50 10 mm 40 30 15 mm 20 10 0 0 0.2 0.4 0.6 0.8 1.0 P (W) VR68 Revision: 02-Jun-2022 Document Number: 28907 6 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VR25, VR37, VR68 www.vishay.com Vishay BCcomponents TESTS PROCEDURES AND REQUIREMENTS All tests are carried out in accordance with the following specifications: Temperature: 15 °C to 35 °C EN 60115-1, generic specification Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar) IEC 60068-2-xx, test methods A climatic category LCT/ UCT / 56 is applied, defined by the lower category temperature (LCT = -55 °C), the upper category temperature (UCT = 155 °C), and the duration of exposure in the damp heat, steady state test (56 days). The components are mounted for testing on printed circuit boards in accordance with IEC 60115-1, 5.5 unless otherwise specified. The table presents only the most important tests, for the full test schedule refer to the documents listed above. However, some additional tests and a number of improvements against those minimum requirements have been included. The tests are carried out under standard atmospheric conditions in accordance with IEC 60068-1, 4.3, whereupon the following values are applied: Relative humidity: 25 % to 75 % TESTS PROCEDURES AND REQUIREMENTS IEC 60115-1 IEC 60068-2 CLAUSE TEST METHOD TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (ΔRmax.) 12.1 Insulation resistance Umax. DC = 500 V during 1 min; V-block method Rins min.: 10 000 MΩ 12.2 Voltage proof URMS = Uins; 60 s No breakdown or flashover 6.2 Temperature coefficient At (20 / -55 / 20) °C and (20 / 155 / 20) °C ≤ ± 200 ppm/K 6.6 Current noise IEC 60195 VR25: max. 5 μV/V VR37: max. 2.5 μV/V VR68: max. 2.5 μV/V 8.1 Short term overload Room temperature; 2.5 x P 70 x R ; (voltage not more than 2 x limiting voltage); 10 cycles; 5 s ON and 45 s OFF ΔR max.: ± 2 % R Robustness of terminations Tensile, bending, and torsion No damage ΔR max.: ± 0.5 % R 21 (Ua1) 21 (Ub) 21 (Uc) 9.5 +235 °C; 2 s; solder bath method; SnPb40 Good tinning (≥ 95 % covered); +245 °C; 3 s; solder bath method; SnAg3Cu0.5 no damage (before aging) 11.1 20 (Ta) Solderability 11.2 20 (Tb) Resistance to soldering heat Unmounted components (260 ± 5) °C; (10 ± 1) s ΔR max.: ± 0.5 % R 10.1 14 (Na) Rapid change of temperature 30 min at -55 °C and 30 min at +155 °C; 5 cycles ΔR max.: ± 0.5 % R 9.9 27 (Ea) Bump 3 x 1500 bumps in 3 directions; 40 g No damage ΔR max.: ± 0.5 % R 9.11 6 (Fc) Vibration 10 sweep cycles per direction; 10 Hz to 2000 Hz; 1.5 mm or 200 m/s2 No damage ΔR max.: ± 0.5 % R 10.3 10.3.4.2 +235 °C; 2 s; solder bath method; SnPb40 Good tinning (≥ 95 % covered); +245 °C; 3 s; solder bath method; SnAg3Cu0.5 no damage (after aging) Climatic sequence: 2 (Bb) Dry heat 16 h; 155 °C 10.3.4.3 30 (Db) Damp heat (accelerated) 1st cycl 24 h; 25 °C to 55 °C; 90 % to 100 % RH 10.3.4.4 1 (Ab) Cold 2 h; -55 °C 10.3.4.5 13 (M) Low air pressure 2 h; 8.5 kPa; 15 °C to 35 °C 10.3.4.6 30 (Db) Damp heat remaining cyclic 5 days; 55 °C; 95 % to 100 % RH; 5 cycles DC load Apply rated power for 1 min 10.3.4.7 Revision: 02-Jun-2022 Rins min.: 1 GΩ ΔR max.: ± 1.5 % R Document Number: 28907 7 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VR25, VR37, VR68 www.vishay.com Vishay BCcomponents TESTS PROCEDURES AND REQUIREMENTS TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (ΔRmax.) Damp heat (steady state) 56 days; 40 °C; 90 % to 95 % RH; loaded with 0.01 P70 (steps: 0 V to 100 V) ΔR max.: ± 1.5 % R 7.1 Endurance (at 70 °C) 1000 h; loaded with P70 or Umax.; 1.5 h ON and 0.5 h OFF ΔR max.: ± 1.5 % R 12.3 Active flammability “cheese-cloth test” Steps of: 5 / 10 / 16 / 25 / 40 x P70 duration 5 min VR25: no flaming of gauze cylinder VR68: no flaming of gauze cylinder 12.4 Passive flammability “needle-flame test” Application of test flame for 20 s No ignition of product; no ignition of under-layer; burning time less than 30 s IEC 60115-1 IEC 60068-2 CLAUSE TEST METHOD 10.4 78 (Cab) DIMENSIONS D d L1 L2 DIMENSIONS - Leaded resistor types, mass, and relevant physical dimensions TYPE Ø Dmax. (mm) L1 max. (mm) L2 max. (mm) Ø d (mm) MASS (mg) VR25 2.5 6.5 7.5 0.58 ± 0.05 212 VR37 4.0 9.0 12.0 0.70 ± 0.03 457 VR68 6.8 18.0 19.0 0.78 ± 0.05 1690 VR25 WITH RADIAL TAPING Lead Spacing (F = 4.8 mm), Size 0207 P2 P DIMENSIONS in millimeters H1 H H0 L L1 W0 W F α P0 P1 Pitch of components P 12.7 ± 1.0 Lead spacing F 4.8 + 0.7 / - 0.0 Width of carrier tape W 18.0 ± 0.5 Body to hole center H 19.5 ± 1.0 Height for cutting (max.) L 11 Height for bending H0 16.5 ± 0.5 Component height (max.) H1 29 D0 α α = 30° to 40° a a Revision: 02-Jun-2022 Document Number: 28907 8 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VR25, VR37, VR68 www.vishay.com Vishay BCcomponents HISTORICAL 12NC INFORMATION • The resistors have a 12-digit numeric code starting with Last Digit of 12NC Indicating Resistance Decade - 2322 241 refers to VR25 RESISTANCE DECADE LAST DIGIT - 2322 242 refers to VR37 100 kΩ to 976 kΩ 4 - 2322 244 refers to VR68 1 MΩ to 9.76 MΩ 5 ≥ 10 MΩ 6 • The subsequent first digit for 1 % tolerance products (E24 and E96 series) or 2 digits for 5 % (E24 series) and 10 % (E12 series) indicate the resistor type and packing • The remaining digits indicate the resistance value: - The first 3 digits for 1 % or 2 digits for 5 % and 10 % tolerance products indicate the resistance value Historical 12NC Example • The 12NC for a VR25, resistor value 7.5 MΩ, 5 % tolerance, supplied on a bandoleer of 1000 units in ammopack, is: 2322 241 13755. • The 12NC for a VR37, resistor value 7.5 MΩ, 5 % tolerance, supplied on a bandoleer of 1000 units in ammopack, is: 2322 242 13755. - The last digit indicates the resistance decade • The 12NC for a VR68, resistor value 7.5 MΩ, 5 % tolerance, supplied on a bandoleer of 500 units in ammopack, is: 2322 244 13755. 12NC CODING FOR VR25, VR37, VR68 - Resistor type and packaging VR25 CODING STARTS WITH 2322 241 ..... VR37 CODING STARTS WITH 2322 242 ..... VR68 CODING STARTS WITH 2322 244 ..... TYPE TOLERANCE (%) BANDOLIER IN AMMOPACK RADIAL TAPED 4000 UNITS VR25 VR37 VR68 BANDOLIER ON REEL STRAIGHT LEADS 52 mm 52 mm 66.7 mm 52 mm 66.7 mm 1000 UNITS 5000 UNITS 500 UNITS 5000 UNITS 750 UNITS ±1 0.... 8.... 7.... - 6.... - ±5 36... 13... 53... - 23... - ± 10 38... 12... 52... - 22... - ±1 - 8.... - - 6.... - ±5 - 13... - - 23... - ±1 - - - 8.... - 6.... ±5 - - - 13... - 23... Revision: 02-Jun-2022 Document Number: 28907 9 For technical questions, contact: filmresistorsleaded@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2022 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2022 1 Document Number: 91000