XC6136N49BMR-G

XC6136 Series ETR02042-004 Ultra-Low Power (88nA) Voltage Detector ■GENERAL DESCRIPTION The XC6136 series is ultra-low power voltage detector with high accuracy detection, manufactured using CMOS process and laser trimming technologies. The device is available in both CMOS and N-channel open drain output configurations. Also detect logic is available in both RESETB (Active Low) and RESET (Active High). Ultra-small low height package USPQ-4B05 and standard packages SSOT-24 and SOT-25 which are ideally suited for small design of portable devices and high densely mounting applications. UVLO circuit is implemented in order to suppress the floating of RESETB pin (undefined operation) when VIN voltage is lower than the minimum operating voltage. ■ FEATURES ■APPLICATIONS Ultra-Low Power ● Energy Harvesting ● Wearable devices High Accuracy ● Smart meter ● Microprocessor logic reset circuitry ● System battery life and charge voltage monitors ● Power-on reset circuits Temperature Characteristics Hysteresis width ● Power failure Detection Detect voltage range Operating voltage range Output type Output logic Undefined operation Protection (CMOS Output only) Packages Environment friendly ■TYPICAL APPLICATION CIRCUIT XC6136 Series RESETB /RESET VIN RPull(*1) ：91nA TYP.(＠detect, VDF=1.2V, VIN=1.1V) ：88nA TYP.(＠release, VDF=1.2V, VIN=1.32V) ：±0.8% (VDF≦3.0V, Ta=25℃) ±1.0% (3.1V≦VDF, Ta=25℃) ：±2.5% (VDF≦3.0V, Ta=-40℃~ 105℃) ±2.7% (3.1V≦VDF, Ta=-40℃~ 105℃) ：±50ppm/℃ (TYP.) ：TYPE:A/C VDF×5.0% (TYP.) TYPE:B/D 2mV ~ 28mV (TYP.) ：1.2V ~ 5.0V (0.1Vstep) ：1.1V ~ 6.0V ：CMOS Nch open drain ：RESETB (Active Low) RESET (Active High) ：Output pin Voltage 0.38V (MAX：Ta=-40℃ ~ 105℃) ＠Power supply Input pin Voltage＜ operating voltage (MIN.) ：USPQ-4B05, SSOT-24, SOT-25 ：EU RoHS Compliant, Pb Free ■TYPICAL PERFORMANCE CHARACTERISTICS VIN RESETB /RESET INPUT VIN2 μ processor VIN1 VSS (*1) VSS Unused for the CMOS output products 1/18 XC6136 Series ■BLOCK DIAGRAMS (1) XC6136C Series A/B type (RESETB OUTPUT:CMOS output/Active Low) VIN RSEN=RA+RB+RC + RA M2 UVLO RESETB - RB M1 VREF RC VSS * Diodes inside the circuits are ESD protection diodes and parasitic diodes. (2) XC6136C Series C/D type (RESET OUTPUT:CMOS output /Active High) VIN RSEN=RA+RB+RC + RA M2 UVLO RESET - RB M1 VREF RC VSS * Diodes inside the circuits are ESD protection diodes and parasitic diodes. 2/18 XC6136 Series ■BLOCK DIAGRAMS (3) XC6136N Series A/B type (RESETB OUTPUT: Nch open drain output /Active Low) VIN RSEN=RA+RB+RC + RA UVLO RESETB - RB M1 VREF RC VSS * Diodes inside the circuits are ESD protection diodes and parasitic diodes (4) XC6136N Series C/D type (RESET OUTPUT: Nch open drain output /Active High) VIN RSEN=RA+RB+RC + RA UVLO RESET - RB M1 VREF RC VSS * Diodes inside the circuits are ESD protection diodes and parasitic diodes 3/18 XC6136 Series ■PRODUCT CLASSIFICATION ●Ordering Information XC6136①②③④⑤⑥-⑦(*1) DESIGNATOR ITEM ① Output Configuration ②③ Detect Voltage ④ Type ⑤⑥-⑦(*1) PKG SYMBOL C N 12 ~ 50 A B C D DESCRIPTION CMOS output Nch open drain output e.g. 1.2V → ②=1, ③=2 Refer to Selection Guide 9R-G USPQ-4B05 (5,000pcs/Reel) NR-G MR-G SSOT-24 (3,000pcs/Reel) SOT-25 (3,000pcs/Reel) (*2) (*1) The “-G” suffix denotes Halogen and Antimony free as well as being fully EU RoHS compliant. (*2) SOT-25 uses Cu bonding wires. ●Selection Guide (*1) TYPE RESETB/RESET OUTPUT HYSTERESIS A Active Low VDF×5.0% (TYP) B ↑ 2mV ~ 28mV (TYP) (*1) C Active High VDF×5.0% (TYP) D ↑ 2mV ~ 28mV (TYP) (*1) Refer to SPEC TABLE. ■ PIN CONFIGURATION ●Type : A/B VSS 3 VIN 4 2 1 NC RESETB USPQ-4B05 (BOTTOM VIEW) VIN RESETB 4 3 1 2 NC SSOT-24VSS (TOP VIEW) ●Type : C/D VSS 3 VIN 4 2 1 NC RESET USPQ-4B05 (BOTTOM VIEW) VIN RESET 4 3 1 NC 2 VSS SSOT-24 (TOP VIEW) NC NC 5 4 1 2 RESETB VIN 3 VSS SOT-25 (TOP VIEW) NC NC 5 4 1 2 V RESET IN 3 VSS SOT-25 (TOP VIEW) *The dissipation pad for the USPQ-4B05 package should be solder-plated in reference mount pattern and metal masking so as to enhance mounting strength and heat release. If the pad needs to be connected to other pins, it should be connected to V SS (No. 3) pin. 4/18 XC6136 Series ■PIN ASSIGNMENT PIN NUMBER USPQ-4B05 SSOT-24 SOT-25 1 3 1 2 3 4 1 2 4 4,5 3 2 (*1) Type A,B (Refer to the ④ in Ordering Information table.) (*2) Type C,D (Refer to the ④ in Ordering Information table.) PIN NAME FUNCTION RESETB RESET NC VSS VIN Reset Output (Active Low) (*1) Reset Output (Active High) (*2) No Connection Ground Power Input ■ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Input Voltage VIN Output Voltage Output Current XC6136C(*2) XC6136N(*3) VRESETB VRESET IRBOUT IROUT XC6136C(*2) XC6136N(*3) RATINGS UNITS -0.3 ~ 7.0 V VSS - 0.3 ~ VIN + 0.3 or 7.0 (*1) VSS - 0.3 ~ 7.0 V V ±50 50 mA 100 USPQ-4B05 550 (40mm x 40mm Standard board) (*4) 150 Power Dissipation (Ta=25℃) SSOT-24 Pd 500 (40mm x 40mm Standard board) (*4) 680 (JESD51-7 board) (*4） mW 250 600 (40mm x 40mm Standard board) (*4) SOT-25 760 (JESD51-7 board) (*4） Operating Ambient Temperature Topr -40 ~ 105 ℃ Storage Temperature Tstg -55 ~ 125 ℃ * All voltages are described based on the VSS. (*1) The maximum value should be either VIN+0.3V or 7.0V in the lowest. (*2) CMOS output (*3) Nch open drain output (*4) The power dissipation figure shown is PCB mounted and is for reference only. Please refer to PACKAGING INFORMATION for the mounting condition. 5/18 XC6136 Series ■ELECTRICAL CHARACTERISTICS -40℃≦Ta≦105℃(*5) Ta=25℃ PARAMETER SYMBOL CONDITIONS UNITS CIRCUIT MIN. Operating Voltage VIN MIN Voltage Holding the VINL Detection(*3) 1.1 VIN=VSEN VDF(T)(*1)=1.2V~3.0V Detect Voltage VDF VDF(T)(*1)=3.1V~5.0V Temperature ΔVDF/ Characteristics (ΔTopr・VDF) TYP. -40℃≦Topr≦105℃ VDF(T) ×0.992 VDF(T) ×0.990 - VDF(T) VDF(T) MAX. MIN. 6.0 1.1 0.4 - VDF(T) VDF(T) ×1.008 ×0.975 VDF(T) VDF(T) ×1.010 ×0.973 ±50 - - TYP. VDF(T) VDF(T) MAX. 6.0 V 0.4 V VDF(T) ×1.025 VDF(T) ×1.027 ±50 - Hysteresis Width VDF VDF VDF VDF VDF VDF (TYPE: A/C) ×0.032 ×0.05 ×0.068 ×0.03 ×0.05 ×0.07 VHYS Hysteresis Width - (TYPE: B/D) E-1(*2) - E-2(*2) V V ① ppm/℃ V V Supply Current1 E-4( *2) (TYPE:A/B) CMOS output Supply Current1 (TYPE:C/D) Iss1 VIN=VDF×0.9 - E-3( *2) - E-5( *2) CMOS output Supply Current1 E-6( *2) (TYPE:A/B/C/D) Nch open drain output nA Supply Current2 ② E-8( *2) (TYPE:A/B) CMOS output Supply Current2 (TYPE:C/D) Iss2 VIN=VDF×1.1 - E-7( *2) - E-9( *2) CMOS output Supply Current2 E-10( *2) (TYPE:A/B/C/D) Nch open drain output Peak of Undefined Operation(*4) (TYPE:A/B) VUNO VIN