TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TOSHIBA Bipolar Linear Integrated Circuit
Silicon Monolithic
TA78L005AP,TA78L006AP,TA78L007AP,TA78L075AP,TA78L008AP,
TA78L009AP,TA78L010AP,TA78L012AP,TA78L132AP,
TA78L015AP,TA78L018AP,TA78L020AP,TA78L024AP
Three-Terminal Positive Regulators
5 V, 6 V, 7 V, 7.5 V, 8 V, 9 V, 10 V, 12 V, 13.2 V, 15 V, 18 V, 20 V, 24 V
Features
z Suitable for TTL, C2MOS power supply.
z Internal overcurrent protection..
z Internal overheating protection.
z Maximum output current of 150 mA (Tj = 25°C).
z Available in a plastic TO-92MOD package.
Pin Assignment
Marking side
Weight: 0.36 g (typ.)
2
3
1
OUT
GND
IN
Marking
TA78L
Part No. (or abbreviation code)
***AP
Lot No.
(weekly code)
Note 1
Note 1: A line under a Lot No. identifies the indication of product Labels.
Not underlined: [[Pb]]/INCLUDES > MCV
Underlined: [[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]]
Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS
compatibility of Product. The RoHS is the Directive 2002/95/EC of the European Parliament and of the Council of 27
January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
The product(s) in this document (“Product”) contain functions intended to protect the Product from
temporary small overloads such as minor short-term overcurrent or overheating. The protective functions do not
necessarily protect Product under all circumstances. When incorporating Product into your system, please
design the system (1) to avoid such overloads upon the Product, and (2) to shut down or otherwise relieve the
Product of such overload conditions immediately upon occurrence. For details, please refer to the notes
appearing below in this document and other documents referenced in this document.
1
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
Equivalent Circuit
Absolute Maximum Ratings (Ta = 25°C)
Characteristics
Symbol
Rating
Unit
TA78L005AP
TA78L006AP
TA78L007AP
TA78L075AP
TA78L008AP
35
TA78L009AP
Input voltage
TA78L010AP
VIN
V
TA78L012AP
TA78L132AP
TA78L015AP
TA78L018AP
40
TA78L020AP
TA78L024AP
Output current
I OUT
0.15
A
PD
800
mW
Operating temperature
Topr
−30 to 85
°C
Storage temperature
Tstg
−55 to 150
°C
Junction temperature
Tj
150
°C
Rth (j-a)
156
°C/W
Power dissipation
Thermal resistance
(Ta = 25°C)
Note 2: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly
even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute
maximum ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
2
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L005AP
Electrical Characteristics
(Unless otherwise specified, VIN = 10 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
4.8
5.0
5.2
V
7.0 V ≤ VIN ≤ 20 V
―
55
150
8.0 V ≤ VIN ≤ 20 V
―
45
100
1.0 mA ≤ IOUT ≤ 100 mA
―
11
60
1.0 mA ≤ IOUT ≤ 40 mA
―
5.0
30
7.0 V ≤ VIN ≤ 20 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
4.75
―
5.25
1.0 mA ≤ IOUT ≤ 70 mA
4.75
―
5.25
Tj = 25°C
―
3.1
6.0
Tj = 125°C
―
―
5.5
8.0 V ≤ VIN ≤ 20 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
40
―
μVrms
―
12
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
8.0 V ≤ VIN ≤ 18 V, Tj = 25°C
41
49
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−0.6
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
3
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L006AP
Electrical Characteristics
(Unless otherwise specified, VIN = 11 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
5.76
6.0
6.24
V
8.1 V ≤ VIN ≤ 21 V
―
50
150
9.0 V ≤ VIN ≤ 21 V
―
45
110
1.0 mA ≤ IOUT ≤ 100 mA
―
12
70
1.0 mA ≤ IOUT ≤ 40 mA
―
5.5
35
8.1 V ≤ VIN ≤ 21 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
5.7
―
6.3
1.0 mA ≤ IOUT ≤ 70 mA
5.7
―
6.3
Tj = 25°C
―
3.1
6.0
Tj = 125°C
―
―
5.5
9.0 V ≤ VIN ≤ 20 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
40
―
μVrms
―
14
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
9.0 V ≤ VIN ≤ 19 V, Tj = 25°C
39
47
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−0.7
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
4
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L007AP
Electrical Characteristics
(Unless otherwise specified, VIN = 12 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
6.72
7.0
7.28
V
9.2 V ≤ VIN ≤ 22 V
―
50
160
10 V ≤ VIN ≤ 22 V
―
45
115
1.0 mA ≤ IOUT ≤ 100 mA
―
13
75
1.0 mA ≤ IOUT ≤ 40 mA
―
6.0
40
9.2 V ≤ VIN ≤ 22 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
6.65
―
7.35
1.0 mA ≤ IOUT ≤ 70 mA
6.65
―
7.35
Tj = 25°C
―
3.1
6.5
Tj = 125°C
―
―
6.0
10 V ≤ VIN ≤ 22 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
50
―
μVrms
―
17
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
10 V ≤ VIN ≤ 20 V, Tj = 25°C
37
46
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−0.75
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
5
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L075AP
Electrical Characteristics
(Unless otherwise specified, VIN = 13 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
7.21
7.5
7.79
V
9.8 V ≤ VIN ≤ 23 V
―
40
170
10.5 V ≤ VIN ≤ 23 V
―
40
120
1.0 mA ≤ IOUT ≤ 100 mA
―
14
80
1.0 mA ≤ IOUT ≤ 40 mA
―
6.5
40
9.8 V ≤ VIN ≤ 23 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
7.125
―
7.875
1.0 mA ≤ IOUT ≤ 70 mA
7.125
―
7.875
Tj = 25°C
―
3.1
6.5
Tj = 125°C
―
―
6.0
10.5 V ≤ VIN ≤ 23 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
60
―
μVrms
―
19
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
11 V ≤ VIN ≤ 21 V, Tj = 25°C
37
45
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−0.75
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
6
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L008AP
Electrical Characteristics
(Unless otherwise specified, VIN = 14 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
7.7
8.0
8.3
V
10.5 V ≤ VIN ≤ 23 V
―
20
175
11 V ≤ VIN ≤ 23 V
―
12
125
1.0 mA ≤ IOUT ≤ 100 mA
―
15
80
1.0 mA ≤ IOUT ≤ 40 mA
―
7.0
40
10.5 V ≤ VIN ≤ 23 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
7.6
―
8.4
1.0 mA ≤ IOUT ≤ 70 mA
7.6
―
8.4
Tj = 25°C
―
3.1
6.5
Tj = 125°C
―
―
6.0
11 V ≤ VIN ≤ 23 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
60
―
μVrms
―
20
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
12 V ≤ VIN ≤ 23 V, Tj = 25°C
37
45
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−0.8
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
7
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L009AP
Electrical Characteristics
(Unless otherwise specified, VIN = 15 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
8.64
9.0
9.36
V
11.4 V ≤ VIN ≤ 24 V
―
80
200
12 V ≤ VIN ≤ 24 V
―
20
160
1.0 mA ≤ IOUT ≤ 100 mA
―
17
90
1.0 mA ≤ IOUT ≤ 40 mA
―
8.0
45
11.4 V ≤ VIN ≤ 24 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
8.55
―
9.45
1.0 mA ≤ IOUT ≤ 70 mA
8.55
―
9.45
Tj = 25°C
―
3.2
6.5
Tj = 125°C
―
―
6.0
12 V ≤ VIN ≤ 24 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
65
―
μVrms
―
21
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
12 V ≤ VIN ≤ 24 V, Tj = 25°C
36
44
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−0.85
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
8
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L010AP
Electrical Characteristics
(Unless otherwise specified, VIN = 16 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
9.6
10
10.4
V
12.5 V ≤ VIN ≤ 25 V
―
80
230
13 V ≤ VIN ≤ 25 V
―
30
170
1.0 mA ≤ IOUT ≤ 100 mA
―
18
90
1.0 mA ≤ IOUT ≤ 40 mA
―
8.5
45
12.5 V ≤ VIN ≤ 25 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
9.5
―
10.5
1.0 mA ≤ IOUT ≤ 70 mA
9.5
―
10.5
Tj = 25°C
―
3.2
6.5
Tj = 125°C
―
―
6.0
13 V ≤ VIN ≤ 25 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
70
―
μVrms
―
22
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
13 V ≤ VIN ≤ 24 V, Tj = 25°C
36
43
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−0.9
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
9
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L012AP
Electrical Characteristics
(Unless otherwise specified, VIN = 19 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
11.5
12
12.5
V
14.5 V ≤ VIN ≤ 27 V
―
120
250
16 V ≤ VIN ≤ 27 V
―
100
200
1.0 mA ≤ IOUT ≤ 100 mA
―
20
100
1.0 mA ≤ IOUT ≤ 40 mA
―
10
50
14.5 V ≤ VIN ≤ 27 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
11.4
―
12.6
1.0 mA ≤ IOUT ≤ 70 mA
11.4
―
12.6
Tj = 25°C
―
3.2
6.5
Tj = 125°C
―
―
6.0
16 V ≤ VIN ≤ 27 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
80
―
μVrms
―
24
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
15 V ≤ VIN ≤ 25 V, Tj = 25°C
36
41
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−1.0
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
10
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L132AP
Electrical Characteristics
(Unless otherwise specified, VIN = 21 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
12.67
13.2
13.73
V
16 V ≤ VIN ≤ 28 V
―
125
270
17 V ≤ VIN ≤ 28 V
―
105
225
1.0 mA ≤ IOUT ≤ 100 mA
―
22
120
1.0 mA ≤ IOUT ≤ 40 mA
―
11
60
16 V ≤ VIN ≤ 28 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
12.54
―
13.86
1.0 mA ≤ IOUT ≤ 70 mA
12.54
―
13.86
Tj = 25°C
―
3.2
6.5
Tj = 125°C
―
―
6.0
17 V ≤ VIN ≤ 28 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
90
―
μVrms
―
28
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
17 V ≤ VIN ≤ 27 V, Tj = 25°C
34
41
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−1.2
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
11
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L015AP
Electrical Characteristics
(Unless otherwise specified, VIN = 23 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
14.4
15
15.6
V
17.5 V ≤ VIN ≤ 30 V
―
130
300
20 V ≤ VIN ≤ 30 V
―
110
250
1.0 mA ≤ IOUT ≤ 100 mA
―
25
150
1.0 mA ≤ IOUT ≤ 40 mA
―
12
75
17.5 V ≤ VIN ≤ 30 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
14.25
―
15.75
1.0 mA ≤ IOUT ≤ 70 mA
14.25
―
15.75
Tj = 25°C
―
3.3
6.5
Tj = 125°C
―
―
6.0
20 V ≤ VIN ≤ 30 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
90
―
μVrms
―
30
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
18.5 V ≤ VIN ≤ 28.5 V, Tj = 25°C
34
40
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−1.3
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
12
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L018AP
Electrical Characteristics
(Unless otherwise specified, VIN = 27 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
17.3
18
18.7
V
21.4 V ≤ VIN ≤ 33 V
―
32
325
22 V ≤ VIN ≤ 33 V
―
27
275
1.0 mA ≤ IOUT ≤ 100 mA
―
30
170
1.0 mA ≤ IOUT ≤ 40 mA
―
15
75
21.4 V ≤ VIN ≤ 33 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
17.1
―
18.9
1.0 mA ≤ IOUT ≤ 70 mA
17.1
―
18.9
Tj = 25°C
―
3.3
6.5
Tj = 125°C
―
―
6.0
22 V ≤ VIN ≤ 33 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
150
―
μVrms
―
45
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
23 V ≤ VIN ≤ 33 V, Tj = 25°C
32
38
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−1.5
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
13
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L020AP
Electrical Characteristics
(Unless otherwise specified, VIN = 29 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
19.2
20
20.8
V
23.5 V ≤ VIN ≤ 35 V
―
33
330
24 V ≤ VIN ≤ 35 V
―
28
285
1.0 mA ≤ IOUT ≤ 100 mA
―
33
180
1.0 mA ≤ IOUT ≤ 40 mA
―
17
90
23.5 V ≤ VIN ≤ 35 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
19.0
―
21.0
1.0 mA ≤ IOUT ≤ 70 mA
19.0
―
21.0
Tj = 25°C
―
3.3
6.5
Tj = 125°C
―
―
6.0
24 V ≤ VIN ≤ 35 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
170
―
μVrms
―
49
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
25 V ≤ VIN ≤ 35 V, Tj = 25°C
31
37
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−1.7
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
14
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L024AP
Electrical Characteristics
(Unless otherwise specified, VIN = 33 V, IOUT = 40 mA, CIN = 0.33 μF, COUT = 0.1 μF,
0°C ≤ Tj ≤ 125°C)
Symbol
Test
Circuit
Output voltage
VOUT
1
Tj = 25°C
Line regulation
Reg·line
1
Tj = 25°C
Load regulation
Reg·load
1
Tj = 25°C
Output voltage
VOUT
1
Characteristics
Quiescent current
Test Condition
Min
Typ.
Max
Unit
23
24
25
V
27.5 V ≤ VIN ≤ 38 V
―
35
350
28 V ≤ VIN ≤ 38 V
―
30
300
1.0 mA ≤ IOUT ≤ 100 mA
―
40
200
1.0 mA ≤ IOUT ≤ 40 mA
―
20
100
27.5 V ≤ VIN ≤ 38 V,
Tj = 25°C 1.0 mA ≤ IOUT ≤ 40 mA
22.8
―
25.2
1.0 mA ≤ IOUT ≤ 70 mA
22.8
―
25.2
Tj = 25°C
―
3.5
6.5
Tj = 125°C
―
―
6.0
28 V ≤ VIN ≤ 38 V
―
―
1.5
1.0 mA ≤ IOUT ≤ 40 mA
―
―
0.1
―
200
―
μVrms
―
56
―
mV/kh
mV
mV
V
mA
IB
1
Quiescent current change
ΔIB
1
Tj = 25°C
Output noise voltage
VNO
2
Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz
ΔVOUT/Δt
1
Ripple rejection
R.R.
3
f = 120 Hz,
29 V ≤ VIN ≤ 39 V, Tj = 25°C
31
35
―
dB
Dropout voltage
VD
1
Tj = 25°C
―
1.7
―
V
TCVO
1
IOUT = 5 mA
―
−2.0
―
mV/°C
Long term stability
Average temperature
coefficient of output voltage
―
15
mA
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
Test Circuit 1/Standard Application
Test Circuit 2
VNO
Test Circuit 3
R.R.
16
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
17
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
TA78L005AP
18
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
Usage Precautions
Destruction of the IC may occur if high voltage in excess of the IC output voltage (typ. value) is applied to the IC
output terminal. In this case, connect a Zener diode between the output terminal and GND to prevent any
application of excessive voltage.
• Low voltage
Do not apply voltage to the Product that is lower than the minimum operating voltage, or the Product’s
protective functions will not operate properly and the Product may be permanently damaged.
• Overcurrent Protection
The overcurrent protection circuits in the Product are designed to temporarily protect Product from minor
overcurrent of brief duration. When the overcurrent protective function in the Product activates,
immediately cease application of overcurrent to Product. Improper usage of Product, such as application of
current to Product exceeding the absolute maximum ratings, could cause the overcurrent protection circuit
not to operate properly and/or damage Product permanently even before the protection circuit starts to
operate.
• Overheating Protection
The thermal shutdown circuits in the Product are designed to temporarily protect Product from minor
overheating of brief duration. When the overheating protective function in the Product activates,
immediately correct the overheating situation. Improper usage of Product, such as the application of heat
to Product exceeding the absolute maximum ratings, could cause the overheating protection circuit not to
operate properly and/or damage Product permanently even before the protection circuit starts to operate.
19
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
Package Dimensions
20
2009-09-30
TA78L005,006,007,075,008,009,10,12,132,15,18,20,24AP
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively “Product”) without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the
Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of
all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes
for Product and the precautions and conditions set forth in the “TOSHIBA Semiconductor Reliability Handbook” and (b) the
instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their
own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such
design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,
diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating
parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR
APPLICATIONS.
• Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring
equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document.
Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or
reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious
public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used
in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling
equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric
power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this
document.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product
or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of
noncompliance with applicable laws and regulations.
21
2009-09-30
工商网监
湘ICP备2023018690号
