TC74LVX374FT

TC74LVX374F/FT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74LVX374F,TC74LVX374FT Octal D-Type Flip-Flop with 3-State Output The TC74LVX374F/FT is a high-speed CMOS octal D-flip flop fabricated with silicon gate CMOS technology. Designed for use in 3-V systems, it achieves high-speed operation while maintaining the CMOS low power dissipation. This device is suitable for low-voltage and battery operated systems. This 8-bit D-type flip-flop is controlled by a clock input (CK) and an output enable input ( OE ). When the OE input is high, the eight outputs are in a high-impedance state. An input protection circuit ensures that 0 to 5.5V can be applied to the input pins without regard to the supply voltage. This device can be used to interface 5V to 3V systems and two supply systems such as battery back up. This circuit prevents device destruction due to mismatched supply and input voltages. TC74LVX374F TC74LVX374FT Features • • • • • • • High-speed: fmax = 160 MHz (typ.) (VCC = 3.3 V) Low power dissipation: ICC = 4 μA (max) (Ta = 25°C) Input voltage level: VIL = 0.8 V (max) (VCC = 3 V) VIH = 2.0 V (min) (VCC = 3 V) Power-down protection is provided on all inputs ∼ Balanced propagation delays: tpLH − tpHL Low noise: VOLP = 0.8 V (max) Pin and function compatible with 74HC374 Weight SOP20-P-300-1.27A TSSOP20-P-0044-0.65A : 0.22 g (typ.) : 0.08 g (typ.) 1 2007-10-17 TC74LVX374F/FT Pin Assignment (top view) IEC Logic Symbol OE CK (1) (11) EN C1 OE Q0 D0 D1 Q1 Q2 D2 D3 Q3 1 2 3 4 5 6 7 8 9 20 19 18 17 16 15 14 13 12 11 VCC Q7 D7 D6 Q6 Q5 D5 D4 Q4 CK D0 D1 D2 D3 D4 D5 D6 D7 (3) (4) (7) (8) (13) (14) (17) (18) 1D (2) (5) (6) (9) (12) (15) (16) (19) Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 GND 10 Truth Table Inputs Outputs D X X L H Z Qn L H OE H L L L CK X X: Don’t care Z: High impedance Qn: No change System Diagram D0 3 D D1 4 D D2 7 D D3 8 D D4 13 D D5 14 D D6 17 D D7 18 D CK 11 CK Q CK Q CK Q CK Q CK Q CK Q CK Q CK Q OE 1 2 Q0 5 Q1 6 Q2 9 Q3 12 Q4 15 Q5 16 Q6 19 Q7 2 2007-10-17 TC74LVX374F/FT Absolute Maximum Ratings (Note) Characteristics Supply voltage range DC input voltage DC output voltage Input diode current Output diode current DC output current DC VCC/ground current Power dissipation Storage temperature Symbol VCC VIN VOUT IIK IOK IOUT ICC PD Tstg Rating −0.5 to 7.0 −0.5 to 7.0 −0.5 to VCC + 0.5 −20 ±20 ±25 ±75 Unit V V V mA mA mA mA mW °C 180 −65 to 150 Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Operating Ranges (Note) Characteristics Supply voltage Input voltage Output voltage Operating temperature Input rise and fall time Symbol VCC VIN VOUT Topr dt/dv Rating 2.0 to 3.6 0 to 5.5 0 to VCC −40 to 85 Unit V V V °C ns/V 0 to 100 Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. 3 2007-10-17 TC74LVX374F/FT Electrical Characteristics DC Characteristics Characteristics Symbol Test Condition VCC (V) 2.0 H-level Input voltage L-level VIL ⎯ ⎯ Ta = 25°C Min 1.5 2.0 2.4 ⎯ ⎯ ⎯ Ta = −40 to 85°C Max ⎯ ⎯ ⎯ Unit Typ. ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Min 1.5 2.0 2.4 ⎯ ⎯ ⎯ Max ⎯ ⎯ ⎯ VIH 3.0 3.6 2.0 3.0 3.6 0.5 0.8 0.8 ⎯ ⎯ ⎯ 0.5 0.8 0.8 ⎯ ⎯ ⎯ V H-level Output voltage L-level VOH IOH = −50 μA VIN = VIH IOH = −50 μA or VIL IOH = −4 mA VIN = VIH IOL = 50 μA or VIL IOL = 4 mA VIN = VIH or VIL VOUT = VCC or GND VIN = 5.5 V or GND VIN = VCC or GND IOL = 50 μA 2.0 3.0 3.0 2.0 3.0 3.0 3.6 3.6 3.6 1.9 2.9 2.58 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 2.0 3.0 ⎯ 1.9 2.9 2.48 ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ 0 0 ⎯ ⎯ ⎯ ⎯ 0.1 0.1 0.36 ±0.25 ±0.1 0.1 0.1 0.44 ±2.5 ±1.0 V VOL 3-state output Off-state current Input leakage current Quiescent supply current IOZ IIN ICC μA μA μA 4.0 40.0 Timing Requirements (input: tr = tf = 3 ns) Characteristics Minimum pulse width (CK) Minimum set-up time Symbol tW (H) tW (L) ts Test Condition VCC (V) ⎯ Ta = 25°C Limit 7.5 5.0 6.5 4.5 2.0 2.0 Ta = −40 to 85°C Limit 8.0 5.5 6.5 4.5 2.0 2.0 Unit 2.7 3.3 ± 0.3 2.7 3.3 ± 0.3 2.7 3.3 ± 0.3 ns ⎯ ns Minimum hold time th ⎯ ns 4 2007-10-17 TC74LVX374F/FT AC Characteristics (input: tr = tf = 3 ns) Characteristics Symbol Test Condition VCC (V) CL (pF) tpLH ⎯ Ta = 25°C Min ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ Ta = −40 to 85°C Max 16.3 19.8 10.6 14.1 14.5 18.0 9.3 12.8 18.5 13.2 ⎯ ⎯ ⎯ ⎯ Unit Typ. 8.5 11.0 6.7 9.2 7.6 10.1 5.9 8.4 11.5 9.6 115 60 160 95 ⎯ ⎯ Min 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 50 40 85 55 ⎯ ⎯ ⎯ ⎯ ⎯ Max 19.5 23.0 12.5 16.0 17.5 21.0 11.0 14.5 22.0 15.0 ⎯ ⎯ ⎯ ⎯ 2.7 15 50 15 50 15 50 15 50 50 50 15 50 15 50 50 50 (Note 2) Propagation delay time (CK-Q) ns tpHL 3.3 ± 0.3 tpZL Output enable time tpZH tpLZ tpHZ RL = 1 kΩ 2.7 ns 3.3 ± 0.3 2.7 3.3 ± 0.3 2.7 Output disable time RL = 1 kΩ ns 60 45 100 60 ⎯ ⎯ ⎯ ⎯ Maximum clock frequency fmax ⎯ MHz 3.3 ± 0.3 tosLH tosHL CIN COUT CPD ⎯ Output to output skew Input capacitance Output capacitance Power dissipation capacitance (Note 1) 2.7 3.3 ± 0.3 1.5 1.5 10 ⎯ ⎯ 1.5 1.5 10 ⎯ ⎯ ns pF pF pF 4 6 32 (Note 3) ⎯ Note 1: Parameter guaranteed by design. (tosLH = |tpLHm − tpLHn|, tosHL = |tpHLm − tpHLn|) Note 2: Parameter guaranteed by design. Note 3: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption. Average operating current can be obtained by the equation: ICC (opr) = CPD･VCC･fIN + ICC/8 (per F/F) And the total CPD when n pcs. of Flip Flop operate can be gained by the following equation: CPD (total) = 20 + 12･n 5 2007-10-17 TC74LVX374F/FT Noise Characteristics (Ta = 25°C, input: tr = tf = 3 ns, CL = 50 pF) Characteristics Quiet output maximum dynamic VOL Quiet output minimum dynamic VOL Minimum high level dynamic input voltage VIH Maximum low level dynamic input voltage VIL Symbol VOLP VOLV VIHD VILD Test Condition ⎯ ⎯ ⎯ ⎯ VCC (V) 3.3 3.3 3.3 3.3 Typ. 0.5 −0.5 ⎯ ⎯ Limit 0.8 −0.8 Unit V V V V 2.0 0.8 Input Equivalent Circuit INPUT 6 2007-10-17 TC74LVX374F/FT Package Dimensions Weight: 0.22 g (typ.) 7 2007-10-17 TC74LVX374F/FT Package Dimensions Weight: 0.08 g (typ.) 8 2007-10-17 TC74LVX374F/FT RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN GENERAL • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 9 2007-10-17