TMV1212DEN

DC/DC Converters TMV-EN Series,  Watt Features ◆ Isolation test voltage 6’000 Vpk ◆ With reinforced insulation, rated for 250 Vrms working voltage CB Scheme UL 60950-1 ◆ Physical clearance of isolation barrier 2.0 mm min. ◆ Certified to IEC/EN/UL 60950- Safety Standards ◆ ◆ ◆ ◆ ◆ Safety barrier 00% production test Low coupling capacity Single-in-line package (SIP) Lead-free design, RoHS compliant 3-year product warranty The TMV-EN series is a range of 1 W DC/DC converters with high I/O-isolation. This product features an isolation barrier which is approved for supplementary an reinforced insulation. SMD construction and a special designed toroidal transformer made it possible to built these converters in a standard SIP package with a very small footprint. These features making the TMV-EN series an economical solution in many DC/DC converter applications requiring safety agency approval. Models Order code TMV 0505EN TMV 052EN TMV 055EN TMV 0505DEN TMV 052DEN TMV 055DEN TMV 205EN TMV 22EN TMV 25EN TMV 205DEN TMV 22DEN TMV 25DEN 2 VDC ±0 % 5 VDC ±0 % Input voltage Output voltage 5 VDC 12 VDC 15 VDC ± 5 VDC ±12 VDC ±15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ±12 VDC ±15 VDC Output current max. 200 mA 80 mA 65 mA ±100 mA ± 40 mA ± 30 mA 200 mA 80 mA 65 mA ±100 mA ± 40 mA ± 30 mA Efficiency typ. 65 % 65 % 65 % 65 % 71 % 72 % 65 % 65 % 65 % 65 % 73 % 74 % http://www.tracopower.com Page  of 3 DC/DC Converters TMV-EN Series Input Specifications Input current no load/full load Surge voltage (1 sec. max.) Reverse voltage protection Reflected input ripple current Input filter 5 Vin models: 55 mA/300 mA typ. 12 Vin models: 30 mA/125 mA typ. 5 Vin models: 9 V max. 12 Vin models: 18 V max. 0.3 A max. can be reduced by ext. 1–3.3 µF polyester film capacitor internal capacitor ±3 % ±1 % max. ±1.2 %/1% change Vin 1‘000 Mohm 300 VACrms IEC/EN 60950-1, UL 60950-1 CSA C22.2 No. 60950-1-03 – CB report – CSA certification – Operating – Case temperature – Storage w ww.tracopower.com/products/tmv-en_cb.pdf w ww.tracopower.com/products/tmv-en_csa.pdf –40 °C to +85 °C +105 °C max. –40 °C to +125 °C 4 %/K above 70 °C 95 % rel H max. ±0.02 %/K typ. >2’000’000 h @ 25 °C 50 kHz typ. (frequency modulation) ±30 % max. – Input variation – Load variation 20 – 100 %  Watt Output Specifications Voltage set accuracy Voltage balance ( dual output models) Regulation Ripple and noise (20 MHz Bandwidth) Temperature coefficient Short circuit protection Capacitive load Isolation /Safety Isolation voltage Isolation capacity (input/output) Isolation resistance (input/output) Working voltage (rated) Safety standards Safety approvals General Specifications Temperature ranges Derating Humidity (non condensing) Temperature coefficient Reliability, calculated MTBF ( MIL-HDBK-217E) Switching frequency Frequency change over line and load All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TMV-EN Series Physical Specifications Case material Package weight Soldering temperature non-conducting FR4 ( UL 94V-0 rated) 4.0 g (0.14 oz) max. 265°C / 10 sec  Watt Outline Dimensions Pin-Out 12.5 (0.49) Pin  2 5 6 7 Single +Vin (Vcc) –Vin (GND) –Vout No pin +Vout Dual +Vin (Vcc) –Vin (GND) –Vout Common +Vout 0.5 (0.02) ± 0.5 3.5 2.54 (0.16) 4.0 7.62 (0.3) 2.54 2.54 (0.1) (0.1) 0.5 (0.02) (0.14 (0.1) ±0.02) 22.0 (0.87) 0.5 (0.02) 0.25 (0..01) 5.5 (0.22) Bottom view 1 2 5 6 7 7.5 (0.3) 0.5 (0.02) Specifications can be changed any time without notice. Rev. 11/07.1 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · info@traco.ch · www.tracopower.com 2 (0.08) () = inches Tolerances ±0.25 (0.01) pins ±0.05 (0.002) Page 3 of 3