855742

Data Sheet Features • • • • • • • For broadband applications Typical 3dB bandwidth of 3.8 MHz High attenuation Single-ended operation Ceramic Surface Mount Package (SMP) Small size Replaces Sawtek Part 851549 (BW 3dB=3.5MHz) Part Number 855742 70 MHz SAW Filter • Package Surface Mount 15.3 x 6.50 x 1.50 mm Pin Configuration Bottom View 1 2 3 4 5 1.50 NOM. 1.65 MAX. 0.64 10 15.3 1.80 1.91 R0.51 6.50 2.31 1.02 9 8 7 6 Pin No. 5 10 1,6 2,3,4,7,8,9 Description Output Input Ground Case ground Dimensions shown are nominal in millimeters All tolerances are ±0.15mm except overall length and width +0.15mm/-0.10mm Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 0.5 - 1.0µm, over a 2 - 6µm Ni plating Subject to change or obsolescence without notice Rev A 01-Feb-2002 Page 1 of 5 Data Sheet Operating Temperature Range: (2) 0 to +70 oC Part Number 855742 70 MHz SAW Filter Electrical Specifications (1) Parameter (3) Center Frequency Minimum Insertion Loss Lower 1 dB Bandedge(4) Upper 1 dB Bandedge Lower 3 dB Bandedge(4) Upper 3 dB Bandedge Lower 40 dB Bandedge(4) Upper 40 dB Bandedge Amplitude Variation 68.6 - 71.4 MHz Phase Linearity 68.6 - 71.4 MHz Group Delay Variation 68.6 - 71.4 MHz Absolute Delay Relative Attenuation(4) 10 - 30 MHz 30 - 66.7 MHz 73.3 - 110 MHz 110 - 200 MHz Source Impedance: (5) Load Impedance: (5) Substrate Material Temperature Coefficient of Frequency Notes: 1. 2. 3. 4. 5. Minimum 71.4 71.8 67 50 44 40 50 - Typical 70 19 68.35 71.68 68.12 71.92 67.31 72.75 0.6 3.5 84 2.03 58 49 46 60 50 50 LiTaO3 -23 Maximum 22 68.6 68.2 73 1 6 150 - Unit MHz dB MHz MHz MHz MHz MHz MHz dB p-p deg p-p nsec µsec dB dB dB dB Ω Ω ppm/oC - All specifications are based on the test circuit shown below In production, devices will be tested at room temperature to a guardbanded specification to ensure electrical compliance over temperature Electrical margin has been built into the design to account for the variations due to temperature drift and manufacturing tolerances All attenuation measurements are measured relative to minimum insertion loss This is the optimum impedance in order to achieve the performance shown Test Circuit: Actual matching values may vary due to PCB layout and parasitics 120nH 12pF 10 5 270nH 50Ω 82nH 50 Ω Single-ended 50Ω 33pF 1,2,3,4 6,7,8,9 Subject to change or obsolescence without notice Rev A 01-Feb-2002 Page 2 of 5 Data Sheet Part Number 855742 70 MHz SAW Filter Typical Performance (at +25oC) Subject to change or obsolescence without notice Rev A 01-Feb-2002 Page 3 of 5 Data Sheet Actual matching values may vary due to PCB layout and parasitics 120nH 12pF 10 5 82nH Part Number 855742 70 MHz SAW Filter Matching Schematics 50 Ω Single-ended 50Ω 33pF 1,2,3,4 6,7,8,9 270nH 50Ω Marking PCB Footprint 8.84 SAWTEK 855742 XXXXXX ID dot Date code 6.70 2.00 1.22 .69 The date code consists of: JJJ = Julian day, Y = last digit of year, M = manufacturing site code This footprint represents a recommendation only Dimensions shown are nominal in millimeters Tape and Reel 2.7 24.8 Ø330 ID dot 0.3 2.0 4.0 Ø1.5 A 1.75 11.5 16.0 Ø102 Ø20.2 Ø13.0 Direction of travel 24 2.0 2.3 Section A-A 7.1 12.0 Ø1.5 A Dimensions shown are nominal in millimeters Packaging quantity: 2000 units/reel Subject to change or obsolescence without notice Rev A 01-Feb-2002 Page 4 of 5 Data Sheet Maximum Ratings Parameter Operating Temperature Range Storage Temperature Range Part Number 855742 70 MHz SAW Filter Symbol T Tstg Minimum 0 -40 Typical +25 - Maximum +70 +85 Unit o o C C Warnings • • Electrostatic Sensitive Device (ESD) Avoid ultrasonic exposure Links to Additional Technical Information PCB Layout Tips S-Parameters Qualification Flowchart Soldering Profile Other Technical Information Contact Information PO Box 609501 Orlando, FL 32860-9501 USA Subject to change or obsolescence without notice Phone: +1 (407) 886-8860 Fax: +1 (407) 886-7061 Email: custservice@sawtek.com Web: www.sawtek.com Rev A Or contact one of our worldwide Network of sales offices, Representatives or distributors 01-Feb-2002 Page 5 of 5