PD110-41

110 WATT DC TO DC CONVERTERS DESCRIPTION T he PD110 series of DC/DC converters provide up to 110 watts of continuous output power. Available in three standard input range of 10-20 VDC, 18-36 VDC and 36-72 VDC, they are ideal for a variety of applications including telecoms, portable equipment and vehicle mounted instrumentation. All units are available in compact “open PCB” or “enclosed” mechanical formats. P D110 SERIES F E ATU R E S ‧ ‧ ‧ ‧ ‧ ‧ Low cost Small size, light weight 100﹪ burn-in Overvoltage protection Overcurrent protection Three wide input ranges: 1 0-20 VDC, 18-36 VDC and 36-72 VDC I N P U T S P E C I F I C ATI O N S Input voltage： 1 0 t o 2 0 V D C （ P D 11 0 “ L ” s e r i e s ） 1 8 t o 3 6 V D C（ P D 11 0 “ M ” s e r i e s ） 3 6 t o 7 2 V D C （ P D 11 0 “ H ” s e r i e s ） 15A（ rms） for 12VDC 9.4A（ rms） for 24VDC 4.7A（ rms） for 48VDC E N V I R O N M E N TA L S P E C I F I C ATI O N S Operating temperature： St o r a g e t e m p e r a t u r e ： Relative humidity： Derating： 0℃ to +70℃ -40℃ to +85℃ 5﹪ to 95﹪ non-condensing Derate from 100﹪ at +50℃ linearly to 50﹪ at +70℃ Input current： O UTPUT SPECIFICATIONS O utput voltage/current ： Total output power ： R ipple and noise ： O vervoltage protection ： S ee rating chart 110 watts maximum 1 ﹪ peak to peak max. s et at 112 - 132 ﹪ of its nominal output voltage A ll outputs protected to short circuit conditions A ll outputs ±0.04 ﹪ / ℃ m aximum M aximum excursion of 4 ﹪ or b etter on all models, recovering to 1 ﹪ of final value within 500us after a 25 ﹪ step load change G ENERAL SPECIFICATIONS S witching frequency ： E fficiency ： L ine regulation ： W ithstand voltage ： M TBF ： 5 0KHz ±5KHz 7 0 ﹪ minimum at full load ± 0.5 ﹪ maximum at full load 1 000VDC from input to output 4 00,000 hours minimum at full load at 25 ℃ ambient, calculated per MIL-HDBK-217F O vercurrent protection ： Temperature coefficient ： Transient response ： Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● sales@trumpower.com ● w ww.TRUMPower.com DC TO DC CONVERTERS OUTPUT VOLTAGE/CURRENT RATING CHART (3) Model PD110-10 PD110-12 PD110-13 PD110-14 PD110-16 PD110-23 PD110-31 PD110-32 PD110-40 PD110-41 PD110-42 PD110-45-1 PD110-45-2 PD110-46 Output #1 Vnom. Imin. Imax. Tol. 5V 0A 22A 3% 12V 0A 9.0A 2% 15V 0A 7.5A 2% 24V 0A 4.5A 2% 30V 0A 3.6A 2% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% Vnom. Output #2(1) Imin. Imax. Ipeak (N/A) (N/A) (N/A) (N/A) (N/A) 0A 5A 9.0A 0A 5A 9.0A 0A 4A 7.5A 0A 5A 9.0A 0A 4A 7.5A 0A 5A 9.0A 0A 5A 9.0A 0A 3A 5.0A 0A 4A 7.5A Tol. Vnom. Output #3 Imin. Imax. (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) 0A 1A 0A 1A 0A 1A 0A 1A 0A 1A 0A 1A 0A 1A 0A 1A PD110 SERIES Tol. Output #4 Vnom. Imin. Imax. (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) -5V 0A 1A +24V 0A 1A +12V 0A 1A +24V 0A 1.5A +12V 0A 1A -5V 0A 1A Tol. Maximum Output Power (2) 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W +12V +12V +15V +12V +15V +12V +12V +24V +15V 3% 3% 3% 3% 3% 3% 3% 3% 3% -12V -15V -12V -15V -12V -12V -12V -15V 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 4% 10% 4% 4% Notes: (1) Peak output current with 10% maximum duty cycle for less than 60 seconds. (2) PD110”M” & “H” series are suitable only for 110 watts maximum at 20 CFM forced air cooling or 80 watts maximum at convection cooling. PD110”L” series are suitable only for 90 watts maximum at 20 CFM forced air cooling or 70 watts maximum at convection cooling. (3) Suffix codes for input range, mechanical format and connector are as follows. PD110-X1X2X3X4X5, “X1X2” is the model code from the above table, “X3” is the input range (L=10-20 VDC, M=18-36 VDC, H=36-72 VDC), “X4” is the mechanical format (A=open PCB, B=L-bracket, C=enclosed) and “X5” is the input and output connector code (Blank=Molex KK type, T=miniature terminal block), e.g. PD110-31MCT (18-36 VDC input range, enclosed format and miniature terminal blocks). MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inch [mm] 2. Tolerance 0.02 [0.5] maximum 3. Molex KK type connectors: Input connector mates with Molex housing 09-50-3051 and Molex 2878 series crimp terminal. Output connector mates with Molex housing 09-50-3131 and Molex 2878 series crimp terminal. 4. Miniature terminal blocks: Input terminals allow wires up to 2mm2 (AWG #14). Output terminals allow wires up to 2mm2 (AWG #14). 5. Weight: 640grams (PCB format) 6. See the mechanical details of L-bracket and enclosed formats in page 7-2. PIN CHART MINI. TERMINAL MOLEX CONNECTOR 1 1,2,3 OUTPUT #1 2 4,5 RETURN 3 6,7 RETURN 4 8,9 OUTPUT #1 10 N.C. N.C. N.C. N.C. 5 11 N.C. N.C. OUTPUT #3 OUTPUT #3 12 KEY KEY KEY KEY 6 13 N.C. N.C. N.C. OUTPUT #4 MODEL PD110-10 PD110-13 PD110-16 PD110-23 PD110-31 PD110-12 PD110-14 PD110-32 OUTPUT COMMON COMMON OUTPUT #1 RETURN RETURN #2 OUTPUT COMMON COMMON OUTPUT #1 RETURN RETURN #2 PD110-40 PD110-41 OUTPUT COMMON COMMON OUTPUT PD110-42 PD110-45-1 #1 RETURN RETURN #2 PD110-45-2 PD110-46 Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● sales@trumpower.com ● w ww.TRUMPower.com