RGP20K

RGP20A THRU RGP20M 2.0 AMPS. Glass Passivated Junction Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 2.0 Amperes Features High temperature metallurgically bonded constructed Plastic material used carries Underwriters Laboratory Classification 94V-0 Glass passivated cavity-free junction Capable of meeting environmental standards of MIL-S-19500 2.0 amperes operation at TA=55oC with no thermal runaway Typical IR less than 0.2 uA High temperature soldering guaranteed: 350℃/10seconds/.375”(9.5mm) lead length at 5 lbs., 2.3 kg tension DO-201 Mechanical Data Cases: JEDEC DO-201 molded plastic over glass body Lead: Plated Axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting position: Any Weight: 0.03 ounce, 0.8 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol RGP RGP Type Number 20A 20B Maximum Recurrent Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current .375” (9.5mm) Lead Length @TA = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 2.0A Maximum Full Load Reverse Current, Full Cycle Average 0.375”(9.3mm) Lead Length at TA=55oC Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=125℃ Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range RGP RGP RGP RGP RGP Units 20D 20G 20J 20K 20M 200 140 200 400 280 400 2.0 80.0 1.3 100 5.0 200 600 420 600 800 1000 560 700 800 1000 V V V A A V uA uA uA nS pF ℃/W ℃ I(AV) IFSM VF HTIR IR Trr Cj RθJA TJ ,TSTG 150 250 30 40 -65 to + 175 500 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1.0 MHz and Applied VR=4.0 Volts 3. Mount on Cu-Pad Size 10mm x 10mm on P.C.B. - 578 - RATINGS AND CHARACTERISTIC CURVES (RGP20A THRU RGP20M) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT. (A) 2.0 10 FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT. (A) 1.5 RESISTIVE OR INDUCTIVE LOAD 1.0 1 0.5 0.375" (9.5mm) LEAD LENGTH 0 25 50 75 100 o 125 150 175 AMBIENT TEMPERATURE. ( C) 0.1 PEAK FORWARD SURGE CURRENT. (A) 100 FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT TA=550C 8.3ms Single Half Sine Wave JEDEC Method Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.01 .4 .6 .8 1.0 1.2 1.4 1.6 0 FORWARD VOLTAGE. (V) FIG.6- TYPICAL REVERSE CHARACTERISTICS 20 10 1 10 NUMBER OF CYCLES AT 60Hz 100 Tj=125 0C 10 INSTANTANEOUS REVERSE CURRENT. ( A) Tj=100 0C 1 FIG.4- TYPICAL JUNCTION CAPACITANCE 100 JUNCTION CAPACITANCE.(pF) Tj=25 0C f=1.0MHz Vsig=50mVp-p Tj=75 0C 0.1 Tj=25 0C 10 5 1 10 REVERSE VOLTAGE. (V) 100 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) - 579 -