SF16S

SF11S - SF18S 1.0 AMP. Super Fast Rectifiers A-405 Features H igh efficiency, low VF H igh current capability H igh reliability H igh surge current capability L ow power loss. F or use in low voltage, high frequency inventor, free wheeling, and polarity protection application M echanical Data C ases: Molded plastic E poxy: UL 94V-0 rate flame retardant L ead: Pure tin plated, lead free., solderable per MIL-STD-202, Method 208 guaranteed P olarity: Color band denotes cathode H igh temperature soldering guaranteed: 260 oC/10 seconds/.375”,(9.5mm) lead lengths at 5 lbs., (2.3kg) tension W eight: 0.22 gram Dimensions in inches and (millimeters) M aximum Ratings and Electrical Characteristics R ating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% S ymbol SF SF SF SF SF SF SF SF U nits T ype Number 11S 12S 13S 14S 15S 16S 17S 18S M aximum Recurrent Peak Reverse Voltage M aximum RMS Voltage M aximum DC Blocking Voltage M aximum Average Forward Rectified Current .375 (9.5mm) Lead Length o @T A = 5 5 C P eak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) M aximum Instantaneous Forward Voltage @ 1.0A M aximum DC Reverse Current @T A=25 oC at Rated DC Blocking Voltage @ T A=100 oC M aximum Reverse Recovery Time (Note 1) T ypical Junction Capacitance (Note 2) T ypical Thermal Resistance V RRM V RMS V DC I(AV) IFSM VF IR T rr Cj R θJA 50 35 50 100 70 100 150 105 150 200 140 200 300 210 300 400 280 400 500 350 500 600 420 600 V V V A A 1 .0 30 0 .95 5 .0 100 35 30 1 00 -65 to +125 -65 to +150 15 o 1.3 1.7 V uA uA nS pF C/W o C o C O perating Temperature Range TJ S torage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A N otes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Mount on Cu-Pad Size 5mm x 5mm on PCB. Version: A06 RATINGS AND CHARACTERISTIC CURVES (SF11S THRU SF18S) FIG.1- MAXIMUM AVERAGE FORWARD CURRENT DERATING 1.5 FIG.2- TYPICAL REVERSE CHARACTERISTICS 1000 AVERAGE FORWARD CURRENT. (A) 1.0 INSTANTANEOUS REVERSE CURRENT. ( A) Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length 100 0.5 Tj=100 0C 10 0 0 25 50 75 100 125 O 150 175 Tj=25 0C 1 AMBIENT TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 35 PEAK FORWARD SURGE CURRENT. (A) 30 25 20 15 10 5 0 0.1 8.3ms Single Half Sine Wave JEDEC Method 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL FORWARD CHARACTERISTICS 100 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz INSTANTANEOUS FORWARD CURRENT. (A) FIG.4- TYPICAL JUNCTION CAPACITANCE 140 120 100 80 60 40 JUNCTION CAPACITANCE.(pF) 1 SF 11S ~S SF1 F1 0.1 4S 5S~ SF1 8S SF 11 S~ SF 14 S 10 6S F1 ~S 5S S 1 18 SF SF S~ 17 SF 20 0.01 0.4 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.1 0.5 1 2 5 10 20 50 100 200 500 1000 0.6 REVERSE VOLTAGE. (V) 0.8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) 1.6 1.8 FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE +0.5A DUT (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr (+) 50Vdc (approx) (-) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06