SF3001PT_1

SF3001PT - SF3006PT 30.0 AMPS. Glass Passivated Super Fast Rectifiers TO-3P/TO-247AD Features Dual rectifier construction, positive center-tap Plastic package has Underwriters Laboratory Flammability Classifications 94V-0 Glass passivated chip junctions Superfast recovery time, high voltage Low forward voltage, high current capability Low thermal resistance Low power loss, high efficiency High temperature soldering guaranteed : o 260 C / 10 seconds, 0.16”(4.06mm) lead lengths at 5 lbs., (2.3kg) tesion Mechanical Data Cases: JEDEC TO-3P/TO-247AD molded plastic Terminals: Pure tin plated, lead free. solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting position: Any Weight: 0.2 ounce, 5.6 grams Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at Tc=100 oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @15.0A Maximum D.C. Reverse Current @ Tc=25 oC at Rated DC Blocking Voltage @ Tc=100 oC Maximum Reverse Recovery Time(Note2) TJ=25 oC Symbol VRRM VRMS VDC I(AV) IFSM VF IR SF SF SF SF SF SF 3001PT 3002PT 3003PT 3004PT 3005PT 3006PT Units V V V A A 50 35 50 100 70 100 150 105 150 30 300 0.95 10.0 500 35 200 140 200 300 210 300 400 280 400 1.3 V uA uA nS o Trr Cj 175.0 Typical Junction Capacitance (Note 1) RθJC 2.5 Typical Thermal Resistance (Note 3) -55 to +150 TJ Operating Junction Temperature Range TSTG -55 to +150 Storage Temperature Range 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0V D.C. Notes: 2. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Recover to 0.25A. 3. Mounted on 4” x 6” x 0.25” Al-Plate. pF C/W o C o C Version: A06 RATINGS AND CHARACTERISTIC CURVES (SF3001PT THRU SF3006PT) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT. (A) FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG 1000 36 30 24 12 6 0 INSTANTANEOUS REVERSE CURRENT MICRO AMPERES 100 TJ=100 0C TJ=75 0C 10 0 50 100 o 150 CASE TEMPERATURE. ( C) TJ=25 0C PEAK FORWARD SURGE CURRENT. (A) 300 250 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 1 0.1 8.3ms Single Half Sine Wave JEDEC Method Tj=Tj max. 200 150 100 50 0 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 40 SF3001PT-04PT 1 2 5 10 20 50 100 INSTANTANEOUS FORWARD CURRENT. (A) 20 10 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG 1000 500 CAPACITANCE.(pF) 4 SF3005PT-06PT 1 125 0C 25 0C 200 100 50 20 10 0.1 Tj=25oC f=1MHz Vsig=50mVp-p 0.4 Pulse Width=300 s 2% Duty Cycle 0.1 1 5 10 50 100 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.5 FORWARD VOLTAGE. (V) REVERSE VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A DUT (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A (+) 50Vdc (approx) (-) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06