SFD603G

SFD601G THRU SFD608G 6.0 AMPS. Glass Passivated Super Fast Rectifiers Voltage Range 50 to 600 Volts Current 6.0 Amperes Features .250(6.55) .246(6.45) DPAK .211(5.36) .207(5.26) .093(2.35) .089(2.25) .013(0.54) .011(0.48) Ultrafast Recovery Low forward voltage drop High current capability High reliability High surge current capability Marking .274(6.95) .270(6.85) .250(6.55) .246(6.45) .043(1.10) .035(0.90) 05 .384(9.75) .364(9.25) 05 Mechanical Data .024(0.60) 30 5 .112(2.85) .092(2.35) .059(1.45) .039(0.95) Case: Epoxy molded Epoxy: UL 94V-O rate flame retardant Terminals: Leads solderable per MIL-STD202, Method 208 guaranteed Polarity: As marked High temperature soldering guaranteed: 260oC/10 seconds. Weight: 0.4 grams .031(0.80) .013(0.54) .011(0.48) .053(1.30) .045(1.10) .211(5.36) .207(5.26) .165(4.20) .149(3.80) 1 2 3 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol SFD SFD SFD SFD Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current @TC = 137℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @3.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ Maximum Reverse Recovery Time(Note1) Typical Thermal Resistance (Note 3) Typical Junction Capacitance (Note 2) Operating Temperature Range Storage Temperature Range SFD SFD SFD SFD 601G 602G 603G 604G 605G 606G 607G 608G Units V V V A A VRRM VRMS VDC I(AV) IFSM VF IR Trr RθJC Cj TJ TSTG 50 35 50 100 150 200 300 400 500 600 70 105 140 210 280 350 420 100 150 200 300 400 500 600 6.0 50 1.1 5.0 200 35 9.0 50 30 1.3 1.7 V µA µA nS ℃/W pF ℃ ℃ -65 to +150 -65 to +150 Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C. 3. Thermal Resistance from Junction to Case. - 258 - RATINGS AND CHARACTERISTIC CURVES (SFD601G THRU SFD608G) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT. (A) 10 8 6 4 2 0 FIG.3- TYPICAL REVERSE CHARACTERISTICS 1000 INSTANTANEOUS REVERSE CURRENT. ( A) 100 TJ=100 0C 10 0 50 CASE TEMPERATURE. ( C) o 100 150 PEAK FORWARD SURGE CURRENT. (A) 50 40 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG TJ=125 0C 8.3ms Single Half Sine Wave JEDEC Method 1 TJ=25 0C 0.1 0 20 40 60 80 100 120 140 30 20 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.6- TYPICAL FORWARD CHARACTERISTICS PER LEG 100 10 INSTANTANEOUS FORWARD CURRENT. (A) ~S 1 2 5 10 20 50 100 FD 0 NUMBER OF CYCLES AT 60Hz 60 30 10 SF 1G 4G S G~ D FD 60 60 6G FIG.5- TYPICAL JUNCTION CAPACITANCE PER LEG 60 Tj=25 0C 3 1 SF D6 05 SF D6 07 G ~S FD 60 8G 50 CAPACITANCE.(pF) 40 30 20 10 0 0.3 0.1 SF SF D6 D6 01G 05 ~S G~ FD SF 604 D6 G 0.03 0.01 0.4 08 G 10 20 50 100 200 500 1000 Tj=25oC Pulse Width=300 s 1% Duty Cycle 0.6 0.8 1.0 1.2 1.4 1.6 1.8 1 2 5 REVERSE VOLTAGE. (V) FORWARD VOLTAGE. (V) - 259 -