TS7909CI

TS7900 series 3-Terminal Fixed Negative Output Voltage Regulator ITO-220 Pin assignment: 1. Ground 2. Input 3. Output (Heatsink surface connected to Pin 2) Voltage Range - 5V to - 24V Output Current up to 1A General Description The TS7900 series of fixed output negative voltage regulators are intended as complements to the popular TS7800 series device. These negative regulators are available in the same seven-voltage options as the TS7800 devices. In addition, one extra voltage option commonly employed in MECL systems is also available in the negative TS7900 Series. Available in fixed output voltage options from -5.0 to -24 volts, these regulators employ current limiting, thermal shutdown, and safe-area compensation--making them remarkably rugged under most operating conditions. With adequate heatsinking they can deliver output currents in excess of 1 ampere. This series is offered in 3-pin TO-220, ITO-220 package. Features Output current up to 1A No external components required Internal thermal overload protection Internal short-circuit current limiting Output transistor safe-area compensation Output voltage offered in 4% tolerance Standard Application Ordering Information Part No. TS79xxCZ TS79xxCI Operating Temp. (Ambient) -20 ~ +85oC Package TO-220 ITO-220 Note: Where xx denotes voltage option. A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on the Input ripple voltage. XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable distance from power supply filter. ** = Co is not needed for stability; however, it does improve transient response. Absolute Maximum Rating Input Voltage Input Voltage Power Dissipation TO-220 TO-220 ITO-220 Operating Junction Temperature Range Storage Temperature Range Note : * TS7905 to TS7918 ** TS7924 *** Follow the derating curve Vin * Vin ** Without heatsink Pt *** Without heatsink TJ TSTG - 35 - 40 2 15 10 0 ~ +150 -65 ~ +150 o o o V V C/W C C TS7900 series 1-7 2003/12 rev. A TS7905 Electrical Characteristics (Vin= -10V, Iout=500mA, 0 C ≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output voltage Symbol o Test Conditions Tj=25 C -7.5V≤Vin≤ -20V, 10mA≤Iout≤1A, PD≤15W -7.5V≤Vin≤-25V -8V≤Vin≤-12V 10mA≤Iout≤1A 250mA≤Iout≤750mA o Min -4.80 -4.75 Typ -5 -5 Max -5.20 -5.25 Unit V Vout Line Regulation REGline Tj=25 C o o -------- 3 1 15 5 4 --40 74 2 2.1 -1 100 50 100 50 8 1.3 0.5 -----uV dB V A mV/ o mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj Tj=25 C Iout=0, Tj=25 C -7.5V≤Vin≤-25V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -8V≤Vin≤-18V Iout=1.0A, Tj=25 C Tj=25 C Iout=10mA, 0 C ≤Tj≤125 C o o o o o mA -62 ---- C TS7906 Electrical Characteristics (Vin=-11V, Iout=500mA, 0 C ≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output Voltage Symbol o Test Conditions Tj=25 C -8.5V≤Vin≤-21V, 10mA≤Iout≤1A, PD≤15W -8.5V≤Vin≤-25V -9V≤Vin≤-13V 10mA≤Iout≤1A 250mA≤Iout≤750mA o Min -5.75 -6.3 Typ -6 -6 Max -6.25 -6.3 Unit V Vout Line Regulation REGline Tj=25 oC Tj=25 oC -------- 5 1.5 14 4 4 --44 73 2 2.1 -1 120 60 120 60 8 1.3 0.5 -----uV dB V A mV/ o mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj Iout=0, Tj=25 C -8.5V≤Vin≤-25V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -9V≤Vin≤-19V Iout=1.0A, Tj=25 C Tj=25 C Iout=10mA, 0 C ≤Tj≤125 C o o o o o mA -60 ---- C Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS7900 series 2-7 2003/12 rev. A TS7908 Electrical Characteristics (Vin=-14V, Iout=500mA, 0 C ≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output Voltage Symbol o Test Conditions Tj=25 C -10.5V≤Vin≤-23V, 10mA≤Iout≤1A, PD≤15W -10.5V≤Vin≤-25V -11V≤Vin≤-17V 10mA≤Iout≤1A 250mA≤Iout≤750mA o Min -7.69 -7.61 Typ -8 -8 Max -8.32 -8.40 Unit V Vout Line Regulation REGline Tj=25 C o o -------- 6 2 12 4 4 --52 72 2 2.1 -1 160 80 160 80 8 1 0.5 -----uV dB V A mV/ o mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj Tj=25 C Iout=0, Tj=25 C -10.5V≤Vin≤-25V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -11V≤Vin≤-21V Iout=1.0A, Tj=25 C Tj=25 C Iout=10mA, 0 C ≤Tj≤125 C o o o o o mA -56 ---- C TS7909 Electrical Characteristics (Vin=-15V, Iout=500mA, 0 C ≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output Voltage Symbol o Test Conditions Tj=25 C -11.5V≤Vin≤-23V, 10mA≤Iout≤1A, PD≤15W -11.5V≤Vin≤-26V -12V≤Vin≤-17V 10mA≤Iout≤1A 250mA≤Iout≤750mA o Min -8.65 -8.57 Typ -9 -9 Max -9.36 -9.45 Unit V Vout Line Regulation REGline Tj=25 oC Tj=25 oC -------- 6 2 12 4 4 --58 71 2 2.1 -1 180 90 180 90 8 1 0.5 -----uV dB V A mV/ o mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj Iout=0, Tj=25 C -11.5V≤Vin≤-26V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -12V≤Vin≤-22V Iout=1.0A, Tj=25 C Tj=25 C Iout=10mA, 0 C ≤Tj≤125 C o o o o o mA -56 ---- C Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS7900 series 3-7 2003/12 rev. A TS7912 Electrical Characteristics (Vin=-19V, Iout=500mA, 0 C ≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output Voltage Symbol o Test Conditions Tj=25 C -14.5V≤Vin≤-27V, 10mA≤Iout≤1A, PD ≤15W -14.5V≤Vin≤-30V -15V≤Vin≤-19V 10mA≤Iout≤1A 250mA≤Iout≤750mA Min -11.53 -11.42 Typ -12 -12 Max -12.48 -12.60 Unit V Vout Line Regulation REGline Tj=25 C o o -------- 10 3 12 4 4 --75 70 2 2.1 -1 240 120 240 120 8 1 0.5 -----uV dB V A mV/ o mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj Tj=25 C o Tj=25 C, Iout=0 -14.5V≤Vin≤-30V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, 15V≤Vin≤25V Iout=1.0A, Tj=25 C Tj=25 C Iout=10mA, 0 C ≤Tj≤125 C o o o o o mA -55 ---- C TS7915 Electrical Characteristics (Vin=-23V, Iout=500mA, 0 C ≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output Voltage Symbol o Test Conditions Tj=25 C -17.5V≤Vin≤-30V, 10mA≤Iout≤1A, PD ≤15W -17.5V≤Vin≤-30V -18V≤Vin≤-22V 10mA≤Iout≤1A 250mA≤Iout≤750mA Min -14.42 -14.28 Typ -15 -15 Max -15.60 -15.75 Unit V Vout Line Regulation REGline Tj=25 oC Tj=25 oC o -------- 12 3 12 4 4 --90 69 2 2.1 -1 300 150 300 150 8 1 0.5 -----uV dB V A mV/ o mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj Tj=25 C, Iout=0 -17.5V≤Vin≤-30V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -18V≤Vin≤-28V Iout=1.0A, Tj=25 C Tj=25 C Iout=10mA, 0 C ≤Tj≤125 C o o o o o mA -54 ---- C Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS7900 series 4-7 2003/12 rev. A TS79818 Electrical Characteristics (Vin=-27V, Iout=500mA, 0 C ≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output Voltage Symbol o Test Conditions Tj=25 C -21V≤Vin≤-33V, 10mA≤Iout≤1A, PD ≤15W -21V≤Vin≤-33V -22V≤Vin≤-26V 10mA≤Iout≤1A 250mA≤Iout≤750mA Min -17.30 -17.14 Typ -18 -18 Max -18.72 -18.90 Unit V Vout Line Regulation REGline Tj=25 C o o -------- 15 5 12 4 4 --110 68 2 2.1 -1 360 180 360 180 8 1 0.5 -----uV dB V A mV/ o mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj Tj=25 C o Tj=25 C, Iout=0 -21V≤Vin≤-33V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -21V≤Vin≤-31V Iout=1.0A, Tj=25 C Tj=25 C Iout=10mA, 0 C ≤Tj≤125 C o o o o o mA -53 ---- C TS7824 Electrical Characteristics (Vin=-33V, Iout=500mA, 0 C ≤Tj≤125 C, Cin=0.33uF, Cout=0.1uF; unless otherwise specified.) o o Parameter Output Voltage Symbol o Test Conditions Tj=25 C -27V≤Vin≤-38V, 10mA≤Iout≤1A, PD ≤15W -27V≤Vin≤-38V -28V≤Vin≤-32V 10mA≤Iout≤1A 250mA≤Iout≤750mA o Min -23.07 -22.85 Typ -24 -24 Max -24.96 -25.20 Unit V Vout Line Regulation REGline Tj=25 oC Tj=25 oC -------- 18 6 12 4 4 --170 65 2 2.1 -1 480 240 480 240 8 1 0.5 -----uV dB V A mV/ o mV Load Regulation Quiescent Current Quiescent Current Change Output Noise Voltage Ripple Rejection Ratio Voltage Drop Peak Output Current Temperature Coefficient of Output Voltage REGload Iq ∆lq Vn RR Vdrop Io peak ∆Vout/∆Tj Iout=0, Tj=25 C -27V≤Vin≤-38V 10mA≤Iout≤1A 10Hz≤f≤100KHz, Tj=25 C f=120Hz, -27V≤Vin≤-37V Iout=1.0A, Tj=25 C Tj=25 C Iout=10mA, 0 C ≤Tj≤125 C o o o o o mA -50 ---- C Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. TS7900 series 5-7 2003/12 rev. A Electrical Characteristics Curve FIGURE 1 - Worst Case Power Dissipation v.s. Ambient Temperature FIGURE 2 - Peak Output Current v.s. Input-Output Differential Voltage FIGURE 3 –Ripple Rejection v.s. Frequency FIGURE 4 –Ripple Rejection v.s. Output Voltage FIGURE 5 –Output Voltage v.s. Junction Temperature FIGURE 6 –Quiescent Current v.s. Temperature TS7900 series 6-7 2003/12 rev. A TO-220 Mechanical Drawing A B C K L DIM TO-220 DIMENSION MILLIMETERS MIN MAX 10.000 3.240 2.440 0.381 2.345 4.690 12.700 8.382 14.224 3.556 0.508 27.700 2.032 0.255 5.842 10.500 4.440 2.940 6.350 1.106 2.715 5.430 14.732 9.017 16.510 4.826 1.397 29.620 2.921 0.610 6.858 INCHES MIN MAX 0.394 0.128 0.096 0.015 0.092 0.092 0.500 0.330 0.560 0.140 0.020 1.060 0.080 0.010 0.230 0.413 0.175 0.116 0.250 0.040 0.058 0.107 0.581 0.355 0.650 0.190 0.055 1.230 0.115 0.024 0.270 P A B C D J I M E F G H I J K L M N D H F G E O N TS7900 series 7-7 O P ITO-220 Mechanical Drawing ITO-220 DIMENSION DIM A B C D E F G H I J K L M N O MILLIMETERS MIN MAX 10.04 10.07 6.20 (typ.) 2.20 (typ.) 1.40 (typ.) 15.0 0.52 2.35 13.50 1.11 2.60 4.49 15.20 0.54 2.73 13.55 1.49 2.80 4.50 INCHES MIN MAX 0.395 0.396 0.244 (typ.) 0.087 (typ.) 0.055 (typ.) 0.591 0.020 0.093 0.531 0.044 0.102 0.176 0.598 0.021 0.107 0.533 0.058 0.110 0.177 1.15 (typ.) 3.03 3.05 2.60 6.55 2.80 6.65 0.045 (typ.) 0.119 0.120 0.102 0.258 0.110 0.262 2003/12 rev. A