1.5KE6.8A thru 1.5KE540A, 1N6267A thru 1N6303A
www.vishay.com
Vishay General Semiconductor
TransZorb® Transient Voltage Suppressors
FEATURES • Glass passivated chip junction
• Available in uni-directional and bi-directional • 1500 W peak pulse power capability with a 10/1000 μs waveform, repetitive rate (duty cycle): 0.01 % • Excellent clamping capability • Very fast response time • Low incremental surge resistance
Case Style 1.5KE
• AEC-Q101 qualified • Solder dip 275 °C max. 10 s, per JESD 22-B106 • Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC
PRIMARY CHARACTERISTICS
VBR uni-directional VBR bi-directional PPPM PD IFSM (uni-directional only) TJ max. 6.8 V to 540 V 6.8 V to 440 V 1500 W 6.5 W 200 A 175 °C
TYPICAL APPLICATIONS
Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive, and telecommunication.
MECHANICAL DATA
Case: Molded epoxy body over passivated junction Molding compound meets UL 94 V-0 flammability rating Base P/N-E3 - RoHS compliant, commercial grade Base P/NHE3 - RoHS compliant, AEC-Q101 qualified Terminals: Matte tin plated leads, solderable per J-STD-002 and JESD 22-B102 E3 suffix meets JESD 201 class 1A whisker test, HE3 suffix meets JESD 201 class 2 whisker test
Note • 1.5KE250A to 1.5KE540A and 1.5KE250CA to 1.5KE440CA for commercial grade only
DEVICES FOR BI-DIRECTION APPLICATIONS
For bi-directional types, use C or CA suffix (e.g. 1.5KE440CA) Eletrical characteristics apply in both directions.
Polarity: For uni-directional types the color band denotes cathode end, no marking on bi-directional types
MAXIMUM RATINGS (TA = 25 °C unless otherwise noted)
PARAMETER Peak pulse power dissipation with a 10/1000 μs waveform Peak pulse current with a 10/1000 μs waveform (1) Power dissipation on infinite heatsink at TL = 75 °C (fig. 5) Peak forward surge current 8.3 ms single half sine-wave uni-directional only Maximum instantaneous forward voltage at 100 A for uni-directional only (3) Operating junction and storage temperature range
(2) (1)
SYMBOL (fig. 1) PPPM IPPM PD IFSM VF TJ, TSTG
VALUE 1500 See next table 6.5 200 3.5/5.0 - 55 to 175
UNIT W A W A V °C
Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 °C per fig. 2 A (2) Measured on 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum (3) V = 3.5 V for 1.5KE220A and below; V = 5.0 V for 1.5KE250A and above F F
Revision: 22-Nov-11
Document Number: 88301 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
1.5KE6.8A thru 1.5KE540A, 1N6267A thru 1N6303A
www.vishay.com
Vishay General Semiconductor
MAXIMUM MAXIMUM MAXIMUM PEAK CLAMPING TEMPERATURE PULSE VOLTAGE COEFFICENT CURRENT AT IPPM OF VBR IPPM (2) VC (V) (%/°C) (A) 143 10.5 0.057 133 11.3 0.061 124 12.1 0.065 112 13.4 0.068 103 14.5 0.073 96.2 15.6 0.075 89.8 16.7 0.078 82.4 18.2 0.081 70.8 21.2 0.084 66.7 22.5 0.086 59.5 25.2 0.089 54.2 27.7 0.09 49.0 30.6 0.092 45.2 33.2 0.094 40.0 37.5 0.096 36.2 41.4 0.097 32.8 45.7 0.098 30.1 49.9 0.099 27.8 53.9 0.1 25.3 59.3 0.101 23.1 64.8 0.101 21.4 70.1 0.102 19.5 77.0 0.103 17.6 85.0 0.104 16.3 92.0 0.104 14.6 104 0.105 13.3 113 0.105 12.0 125 0.106 10.9 137 0.106 9.9 152 0.107 9.1 165 0.107 8.4 179 0.107 7.2 207 0.106 6.8 219 0.108 6.4 234 0.108 6.1 246 0.108 5.5 274 0.108 4.6 328 0.108 4.4 344 0.110 3.6 414 0.110 3.1 482 0.110 2.7 548 0.110 2.5 602 0.110 2.28 658 0.110 2.15 698 0.110 2.03 740 0.110
ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
JEDEC TYPE NUMBER GENERAL SEMICONDUCTOR PART NUMBER BREAKDOWN MAXIMUM VOLTAGE TEST STAND-OFF REVERSE VBR AT IT (1) CURRENT VOLTAGE LEAKAGE (V) IT VWM AT VWM (mA) (V) ID (4) MIN. MAX. (μA) 6.45 7.14 10 5.80 1000 7.13 7.88 10 6.40 500 7.79 8.61 10 7.02 200 8.65 9.55 1.0 7.78 50 9.50 10.5 1.0 8.55 10 10.5 11.6 1.0 9.40 5.0 11.4 12.6 1.0 10.2 5.0 12.4 13.7 1.0 11.1 5.0 14.3 15.8 1.0 12.8 1.0 15.2 16.8 1.0 13.6 1.0 17.1 18.9 1.0 15.3 1.0 19.0 21.0 1.0 17.1 1.0 20.9 23.1 1.0 18.8 1.0 22.8 25.2 1.0 20.5 1.0 25.7 28.4 1.0 23.1 1.0 28.5 31.5 1.0 25.6 1.0 31.4 34.7 1.0 28.2 1.0 34.2 37.8 1.0 30.8 1.0 37.1 41.0 1.0 33.3 1.0 40.9 45.2 1.0 36.8 1.0 44.7 49.4 1.0 40.2 1.0 48.5 53.6 1.0 43.6 1.0 53.2 58.8 1.0 47.8 1.0 58.9 65.1 1.0 53.0 1.0 64.6 71.4 1.0 58.1 1.0 71.3 78.8 1.0 64.1 1.0 77.9 86.1 1.0 70.1 1.0 86.5 95.5 1.0 77.8 1.0 95.0 105 1.0 85.5 1.0 105 116 1.0 94.0 1.0 114 126 1.0 102 1.0 124 137 1.0 111 1.0 143 158 1.0 128 1.0 152 168 1.0 136 1.0 162 179 1.0 145 1.0 171 189 1.0 154 1.0 190 210 1.0 171 1.0 209 231 1.0 185 1.0 237 263 1.0 214 1.0 285 315 1.0 256 1.0 333 368 1.0 300 1.0 380 420 1.0 342 1.0 418 462 1.0 376 1.0 456 504 1.0 408 1.0 485 535 1.0 434 1.0 513 567 1.0 459 1.0
(+)1.5KE6.8A 1N6267A (+)1.5KE7.5A 1N6268A (+)1.5KE8.2A 1N6269A (+)1.5KE9.1A 1N6270A (+)1.5KE10A 1N6271A (+)1.5KE11A 1N6272A (+)1.5KE12A 1N6273A (+)1.5KE13A 1N6274A (+)1.5KE15A 1N6275A (+)1.5KE16A 1N6276A (+)1.5KE18A 1N6277A (+)1.5KE20A 1N6278A (+)1.5KE22A 1N6279A (+)1.5KE24A 1N6280A (+)1.5KE27A 1N6281A (+)1.5KE30A 1N6282A (+)1.5KE33A 1N6283A (+)1.5KE36A 1N6284A (+)1.5KE39A 1N6285A (+)1.5KE43A 1N6286A (+)1.5KE47A 1N6287A (+)1.5KE51A 1N6288A (+)1.5KE56A 1N6289A (+)1.5KE62A 1N6290A (+)1.5KE68A 1N6291A (+)1.5KE75A 1N6292A (+)1.5KE82A 1N6293A (+)1.5KE91A 1N6294A (+)1.5KE100A 1N6295A (+)1.5KE 110A 1N6296A (+)1.5KE120A 1N6297A (+)1.5KE130A 1N6298A (+)1.5KE150A 1N6299A (+)1.5KE160A 1N6300A (+)1.5KE170A 1N6301A 1N6302A 1.5KE180A 1N6303A 1.5KE200A* 1.5KE220A* 1.5KE250A 1.5KE300A 1.5KE350A 1.5KE400A 1.5KE440A 1.5KE480A 1.5KE510A 1.5KE540A Notes (1) Pulse test: t ≤ 50 ms p (2) Surge current waveform per fig. 3 and derate per fig. 2 (3) All terms and symbols are consistent with ANSI/IEEE CA62.35 (4) For bi-directional types with V 10 V and less the I limit is doubled R D * Bi-directional versions are UL approved under component across the line protection, ULV1414 file number E108274 (1.5KE200CA, 1.5KE220CA) (+) Underwriters laboratory recognition for the classification of protectors (QVGQ2) under the UL standard for safety 497B and file number E136766 for both uni-directional and bi-directional devices
Revision: 22-Nov-11
Document Number: 88301 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
1.5KE6.8A thru 1.5KE540A, 1N6267A thru 1N6303A
www.vishay.com
Vishay General Semiconductor
SYMBOL RθJA RθJL VALUE 75 15.4 °C/ W UNIT
THERMAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)
PARAMETER Typical thermal resistance, junction to ambient Typical thermal resistance, junction to lead
ORDERING INFORMATION (Example)
PREFERRED PIN 1.5KE6.8A-E3/54 1.5KE6.8AHE3/54 (1) Note (1) AEC-Q101 qualified UNIT WEIGHT (g) 0.968 0.968 PREFERRED PACKAGE CODE 54 54 BASE QUANTITY 1400 1400 DELIVERY MODE 13" diameter paper tape and reel 13" diameter paper tape and reel
RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted)
100 150
IPPM - Peak Pulse Current, % IRSM
PPPM - Peak Pulse Power (kW)
tr = 10 µs Peak Value IPPM
10
TJ = 25 °C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM
100
Half Value - IPP IPPM 2 50 10/1000 µs Waveform as defined by R.E.A. td 0 0 1.0 2.0 3.0 4.0
1
0.1 0.1 µs
1.0 µs
10 µs
100 µs
1.0 ms
10 ms
td - Pulse Width (s)
t - Time (ms)
Fig. 1 - Peak Pulse Power Rating Curve
Fig. 3 - Pulse Waveform
Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, %
100
10 000 Uni-Directional Bi-Directional
CJ - Capacitance (pF)
75
VR = 0 1000
50
100
VR = Rated Stand-Off Voltage TJ = 25 °C f = 1.0 MHz Vsig = 50 mVp-p
25
0 0 25 50 75 100 125 150 175 200
10 5 10 100 500
TJ - Initial Temperature (°C)
VBR - Breakdown Voltage (V)
Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature
Fig. 4 - Typical Junction Capacitance
Revision: 22-Nov-11
Document Number: 88301 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
1.5KE6.8A thru 1.5KE540A, 1N6267A thru 1N6303A
www.vishay.com
Vishay General Semiconductor
100
8.0
ΔVC - Incremental Clamping Voltage
7.0
PD - Power Dissipation (W)
Waveform: 10/1000 µs Impulse ΔVC = VC - VBR
1.5KE200 1.5KE130 1.5KE75
6.0 5.0 4.0 3.0 2.0 1.0 0 0 25 50 75 100 125 150 175 200 L = 0.375" (9.5 mm) Lead Lengths
20 10 1.5KE39 2.0 1.0 1.5KE33 1.5KE6.8 1.5KE9.1
0.2 0.1 0.5 1 2 10 50
TL - Lead Temperature (°C)
IPP - Peak Pulse Current (A)
Fig. 5 - Power Derating Curve
Fig. 8 - Incremental Clamping Voltage Curve (Uni-directional)
200
100
ΔVC - Incremental Clamping Voltage
Peak Forward Surge Current (A)
TJ = TJ max. 8.3 ms Single Half Sine-Wave 100
Waveform: 10/1000 µs Impulse ΔVC = VC - VBR 20 10
1.5KE200C
1.5KE75C 2.0 1.0 1.5KE39C 1.5KE30C 1.5KE15C 11C 1.5KE7.5C
0.2 0.1 0.5 1 2 10 20 50
10 1 10 100
Number of Cycles at 60 Hz
IPP - Peak Pulse Current (A)
Fig. 6 - Maximum Non-Repetitive Forward Surge Current Uni-Directional only
Fig. 9 - Incremental Clamping Voltage Curve (Bi-directional)
100
100 1.5KE200 1.5KE130 1.5KE100 1.5KE75
ΔVC - Incremental Clamping Voltage
ΔVC - Incremental Clamping Voltage
Waveform: 8/20 µs Impulse ΔVC = VC - VBR 20 10
20 10
Waveform: 8/20 µs Impulse ΔVC = VC - VBR
1.5KE200C 1.5KE75C 1.5KE39C 1.5KE30C 1.5KE15C 1.5KE11C 1.5KE7.5C
2.0 1.0
1.5KE39 1.5KE33 1.5KE6.8 1.5KE9.1 1.5KE18 1.5KE12
2 1
0.2 0.1 0.5 1 2 10 20 50
0.2 0.1 0.5 1 2.0 10 20 50
IPP - Peak Pulse Current (A)
IPP - Peak Pulse Current (A)
Fig. 7 - Incremental Clamping Voltage Curve (Uni-Directional)
Fig. 10 - Incremental Clamping Voltage Curve (Bi-Directional)
Revision: 22-Nov-11
Document Number: 88301 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
1.5KE6.8A thru 1.5KE540A, 1N6267A thru 1N6303A
www.vishay.com
Vishay General Semiconductor
100
100
Transient Thermal Impedance (°C/W)
Instantaneous Forward Current (A)
10
10
1
TJ = 25 °C Pulse Width = 300 µs 1 % Duty Cycle
1
0.1 0 0.4 0.8 1.2 1.6 2.0
0.1 0.001
0.01
0.1
1
10
100
1000
Instantaneous Forward Voltage (V)
tp - Pulse Duration (s)
Fig. 11 - Instantaneous Forward Voltage Characteristics Curve
Fig. 12 - Typical Transient Thermal Impedance
PACKAGE OUTLINE DIMENSIONS in inches (millimeters)
Case Style 1.5KE
1.0 (25.4) MIN. 0.210 (5.3) 0.190 (4.8) DIA. 0.375 (9.5) 0.285 (7.2)
1.0 (25.4) MIN. 0.042 (1.07) 0.038 (0.96) DIA.
APPLIACTION NOTES
• This series of Silicon Transient Suppressors is used in applications where large voltage transients can permanently damage voltage-sensitive components. • The TVS diode can be used in applications where induced lightning on rural or remote transmission lines presents a hazard to electronic circuitry (ref: R.E.A. specification P.E. 60).
• This Transient Voltage Suppressor diode has a pulse power rating of 1500 W for 1 ms. The response time of TVS diode clamping action is effectively instantaneous (1 x 10-9 s bi-directional); therefore, they can protect integrated circuits, MOS devices, hybrids, and other voltage sensitive semiconductors and components. TVS diodes can also be used in series or parallel to increase the peak power ratings.
Revision: 22-Nov-11
Document Number: 88301 5 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
1
Document Number: 91000