ECG001F-G

ECG001 Product Features • • • • • • DC – 6 GHz +12.5 dBm P1dB at 1 GHz +25 dBm OIP3 at 1 GHz 22 dB Gain at 1 GHz 3.4 dB Noise Figure Available in lead-free / green SOT-89 and SOT-363 pkg styles • Internally matched to 50 Ω The Communications Edge TM Product Information InGaP HBT Gain Block Product Description The ECG001 is a general-purpose buffer amplifier that offers high dynamic range in a low-cost surface-mount package. At 1000 MHz, the ECG001 typically provides 22 dB of gain, +25 dBm Output IP3, and +12.5 dBm P1dB. The ECG001 consists of Darlington pair amplifiers using the high reliability InGaP/GaAs HBT process technology and only requires DC-blocking capacitors, a bias resistor, and an inductive RF choke for operation. The device is ideal for wireless applications and is available in a lowcost, surface-mountable lead-free/green/RoHS-compliant SOT-89 or SOT-363 package. All devices are 100% RF and DC tested. The broadband MMIC amplifier can be directly applied to various current and next generation wireless technologies such as GPRS, GSM, CDMA, and W-CDMA. In addition, the ECG001 will work for other various applications within the DC to 6 GHz frequency range such as CATV and mobile wireless. Functional Diagram GND 4 1 RF IN 2 GND 3 RF OUT ECG001B-G GND 1 6 RF OUT Applications • • • • • Mobile Infrastructure CATV / FTTX W-LAN / ISM RFID WiMAX / WiBro GND 2 5 GND RF IN 3 4 GND ECG001F-G Specifications (1) Parameter Operational Bandwidth Test Frequency Gain Output P1dB Output IP3 (2) Test Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 (2) Noise Figure Device Voltage Device Current Typical Performance (1) Units MHz MHz dB dBm dBm MHz dB dB dB dBm dBm dB V mA Min DC Typ 1000 22.2 +12.5 +25 2000 21.2 35 18 +12.5 +26 3.4 3.4 30 Max 6000 Parameter Frequency S21 S11 S22 Output P1dB Output IP3 (2) Noise Figure Units MHz dB dB dB dBm dBm dB 500 22.6 -46 -29 +12 +23 3.4 Typical 900 22.4 -42 -24 +12.5 +25 3.4 1900 21.4 -35 -18 +12.5 +26 3.4 2140 21.0 -29 -17 +12.5 +26 3.4 20.45 21.95 +23 3.0 4 3.8 1. Test conditions unless otherwise noted: 25 ºC, Supply Voltage = +5 V, Rbias = 51 Ω, 50 Ω System. 2. 3OIP measured with two tones at an output power of –1 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. Absolute Maximum Rating Parameter Operating Case Temperature Storage Temperature Device Current RF Input Power (continuous) Junction Temperature -40 to +85 °C -55 to +150 °C 150 mA +12 dBm +250 °C Ordering Information Part No. ECG001B-G ECG001F-G ECG001B-PCB ECG001F-PCB Rating Description InGaP HBT Gain Block (lead-free/green/RoHS-compliant SOT-89 package) InGaP HBT Gain Block (lead-free/green/RoHS-compliant SOT-363 package) 700 – 2400 MHz Fully Assembled Eval. Board 700 – 2400 MHz Fully Assembled Eval. Board Specifications and information are subject to change without notice Operation of this device above any of these parameters may cause permanent damage. WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 1 of 6 April 2006 ECG001 Frequency S21 S11 S22 Output P1dB Output IP3 Noise Figure The Communications Edge TM Product Information InGaP HBT Gain Block Typical Device RF Performance Supply Bias = +5 V, Rbias = 51 Ω, Icc = 30 mA MHz dB dB dB dBm dBm dB 100 22.8 -48 -34 +11.6 +23.6 3.4 500 22.6 -46 -29 +11.6 +23.5 3.4 900 22.4 -42 -24 +12.6 +24.8 3.4 1900 21.4 -35 -18 +12.6 +26 3.4 2140 21.0 -29 -17 +12.6 +25.6 3.4 2400 20.7 -28 -16 +12.8 +25.4 3.4 3500 19.2 -22 -13 +12.2 +23 5800 16.1 -14 -8 +11 1. Test conditions: T = 25º C, Supply Voltage = +5 V, Device Voltage = +3.4 V, Rbias = 51 Ω, Icc = 30 mA typical, 50 Ω System. 2. 3OIP measured with two tones at an output power of -1 dBm/tone separated by 1 MHz. The suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule. 3. Data is shown as device performance only. Actual implementation for the desired frequency band will be determined by external components shown in the application circuit. Gain 24 22 Return Loss Icc vs. Vde 100 80 Ic c ( m A ) S11 S22 60 40 20 0 0 -10 -20 -30 -40 20 18 16 14 S 1 1 , S 2 2 (d B ) G a in ( d B ) 0 1 2 3 4 5 6 0 1 2 3 4 5 6 3.2 3.3 Frequency (GHz) OIP3 vs. Frequency 28 26 OIP3 (dBm) 24 22 +25C 20 500 1000 -40C +85C 2500 3000 0 500 1000 N F (d B ) 5 4 3 2 1 Frequency (GHz) Noise Figure vs. Frequency 18 16 P1dB (dBm) 14 12 10 8 +25C 1500 2000 Frequency (MHz) 2500 3000 3.4 Vde (V) 3.5 3.6 P1dB vs. Frequency -40C +85C 2500 3000 1500 2000 Frequency (MHz) 6 500 1000 1500 2000 Frequency (MHz) Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 2 of 6 April 2006 ECG001 The Communications Edge TM Product Information InGaP HBT Gain Block Recommended Application Circuit Vcc Icc = 30 mA R4 Bias Resistor C4 Bypass Capacitor C3 0.018 µF L1 RF Choke RF IN ECG001 C1 Blocking Capacitor C2 Blocking Capacitor RF OUT ECG001B-PCB ECG001F-PCB Reference Designator L1 C1, C2, C4 50 820 nH .018 µF Recommended Component Values Frequency (MHz) 500 900 1900 2200 220 nH 68 nH 27 nH 22 nH 1000 pF 100 pF 68 pF 68 pF 2500 18 nH 56 pF 3500 15 nH 39 pF 1. The proper values for the components are dependent upon the intended frequency of operation. 2. The following values are contained on the evaluation board to achieve optimal broadband performance: Ref. Desig. L1 C1, C2 C3 C4 R4 Value / Type 39 nH wirewound inductor 56 pF chip capacitor 0.018 μF chip capacitor Do Not Place 51Ω 1% tolerance Size 0603 0603 0603 0805 Recommended Bias Resistor Values Supply R1 value Size Voltage 5V 53.3 ohms 0805 6V 86.7 ohms 0805 8V 153 ohms 1210 9V 187 ohms 1210 10 V 220 ohms 2010 12 V 287 ohms 2010 The proper value for R1 is dependent upon the supply voltage and allows for bias stability over temperature. WJ recommends a minimum supply bias of +5 V. A 1% tolerance resistor is recommended. Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 3 of 6 April 2006 ECG001 The Communications Edge TM Product Information InGaP HBT Gain Block ECG001B-G Mechanical Information This package is lead-free/Green/RoHS-compliant. The plating material on the leads is NiPdAu. It is compatible with both lead-free (maximum 260 °C reflow temperature) and leaded (maximum 245 °C reflow temperature) soldering processes. Outline Drawing Product Marking The component will be marked with an “E001G” designator with an alphanumeric lot code on the top surface of the package. The obsolete tin-lead package is marked with an “E001” designator followed by an alphanumeric lot code; it may also have been marked with a “B” designator followed by a 3digit numeric lot code. Tape and reel specifications for this part are located on the website in the “Application Notes” section. MSL / ESD Rating Land Pattern ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114 MSL Rating: Level 3 at +260 °C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Config. Notes 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135”) diameter drill and have a final plated thru diameter of .25 mm (.010”). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 4 of 6 April 2006 ECG001 The Communications Edge TM Product Information InGaP HBT Gain Block ECG001F-G Mechanical Information This package is lead-free/Green/RoHS-compliant. The plating material on the leads is annealed matte tin over copper. It is compatible with both lead-free (maximum 260 °C reflow temperature) and leaded (maximum 245 °C reflow temperature) soldering processes. Outline Drawing Product Marking The component will be marked with a two-digit numeric lot code (shown as “XX”) followed with a “4” designator on the top surface of the package. The obsolete tin-lead package is marked with a two-digit numeric lot code followed with a “0” designator; it may also have been marked with a “00” designator followed by a letter lot code. Tape and reel specifications for this part are located on the website in the “Application Notes” section. MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1A Passes between 250 and 500V Human Body Model (HBM) JEDEC Standard JESD22-A114 MSL Rating: Level 3 at +260 °C convection reflow Standard: JEDEC Standard J-STD-020 Mounting Config. Notes Land Pattern 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35mm (#80 / .0135”) diameter drill and have a final plated thru diameter of .25 mm (.010”). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via region contacts the heatsink. 4. Do not put solder mask on the backside of the PC board in the region where the board contacts the heatsink. 5. RF trace width depends upon the PC board material and construction. 6. Use 1 oz. Copper minimum. 7. All dimensions are in millimeters (inches). Angles are in degrees. Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 5 of 6 April 2006 ECG001 Freq (MHz) S11 (dB) The Communications Edge TM Product Information InGaP HBT Gain Block Typical Device S-Parameters – ECG001B-G S-Parameters (Vdevice = +3.4 V, ICC = 30 mA, T = 25°C, calibrated to device leads) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 50 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 -51.06 -45.85 -41.11 -35.04 -32.25 -27.68 -25.13 -22.38 -20.32 -17.95 -14.93 -14.55 -12.63 -78.50 -105.39 -132.48 -155.82 -149.35 161.65 146.56 130.02 112.40 95.14 76.82 61.65 48.56 22.77 22.61 22.25 21.78 21.22 20.56 19.94 19.24 18.52 17.91 17.08 16.46 15.70 177.87 158.52 137.66 117.56 98.36 80.02 62.40 44.75 27.97 10.80 -5.29 -20.95 -37.55 -24.25 -23.97 -23.88 -23.47 -23.29 -22.64 -22.19 -21.46 -21.48 -21.10 -20.43 -20.18 -19.59 -0.35 -2.11 -7.72 -11.71 -15.07 -22.26 -28.01 -36.02 -45.09 -54.41 -62.18 -74.36 -85.56 -34.47 -28.80 -23.20 -19.45 -17.31 -15.75 -14.33 -12.76 -12.00 -10.35 -9.12 -8.97 -7.38 -14.76 -88.38 -124.85 -147.22 -176.10 160.80 143.60 119.33 102.25 83.68 67.46 52.66 34.72 Typical Device S-Parameters – ECG001F-G S-Parameters (Vdevice = +3.4 V, ICC = 30 mA, T = 25°C, calibrated to device leads) Freq (MHz) S11 (dB) S11 (ang) S21 (dB) S21 (ang) S12 (dB) S12 (ang) S22 (dB) S22 (ang) 50 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 -33.58 -24.53 -32.76 -28.56 -25.13 -28.01 -28.65 -28.35 -25.99 -22.91 -19.69 -17.30 -15.88 15.96 12.09 32.44 153.22 172.50 -117.92 -133.85 -142.02 -171.80 160.22 153.85 152.52 144.43 22.85 22.63 22.20 21.54 20.74 20.11 19.33 18.59 17.77 17.05 16.39 15.78 15.21 178.01 162.01 144.90 129.42 114.94 103.13 91.28 79.59 68.13 57.38 48.12 39.49 30.49 -24.47 -24.14 -23.99 -23.56 -23.12 -22.71 -22.14 -21.68 -20.88 -20.50 -20.03 -19.55 -19.14 -1.35 1.89 4.76 7.59 9.11 7.41 7.37 4.16 2.49 2.47 -0.55 -5.36 -6.76 -28.60 -22.29 -25.75 -20.80 -17.59 -20.44 -18.13 -16.41 -14.29 -12.47 -11.36 -11.30 -11.31 3.58 -35.35 -100.14 -165.24 175.89 169.69 154.41 140.24 124.73 116.41 113.60 114.22 113.24 Device S-parameters are available for download off of the website at: http://www.wj.com Specifications and information are subject to change without notice WJ Communications, Inc • Phone 1-800-WJ1-4401 • FAX: 408-577-6621 • e-mail: sales@wj.com • W eb site: www.wj.com Page 6 of 6 April 2006