HMJ8_07

High Dynamic Range FET Mixer HMJ8 Product Features x +37 dBm IIP3 x No External Matching Elements Required Product Description The HMJ8 is a high dynamic range GaAs FET mixer. This active FET mixer realizes a typical third order intercept point of +37 dBm at an LO drive level of +18 dBm. The HMJ8 comes in a low cost, 18-pin J-Lead package. Typical applications include frequency up/down conversion, modulation and demodulation for receivers and transmitters used in communication systems. Functional Diagram x RF 2200 - 2300 MHz x LO 2060 - 2160 MHz x IF 50 - 150 MHz x +18 dBm LO Drive Level x +3V Bias (22 mA) x Low Cost SMT J-Lead Package Function IF LO RF +3V Ground Pin No. 2 11 17 8 All other pins Specifications (1) Parameter RF Frequency Range LO Frequency Range IF Frequency Range SSB Conversion Loss Noise Figure LO-RF Isolation LO-IF Isolation RF-IF Isolation Input IP3 RF Return Loss LO Return Loss IF Return Loss Input P1dB LO Drive Level DC Current at +3V Bias Units MHz MHz MHz dB dB dB dB dB dBm dB dB dB dBm dBm mA Min Typ 2200 – 2300 2060 – 2160 50 – 150 8.0 10.5 27 30 15 37 11 8.5 14 +23 +18 22 Max Condition 9.0 22 20 32 35 1. Test conditions unless otherwise noted: 25 ºC, RF = 2250 MHz @ -10 dBm, LO = 2110 MHz @ +18 dBm, IF = 140 MHz Absolute Maximum Rating Parameters Operating Case Temperature Storage Temperature Maximum Input Power -40 to +85 qC -65 to +100 qC +25 dBm Ordering Information Part No. HMJ8 HMJ8-PCB Rating Description High Dynamic Range FET Mixer Fully Assembled Application Circuit 1. Operation of this device above any of these parameters may cause permanent damage. 2. Total sum of LO port and RF port power should not exceed 25 dBm Specifications and information are subject to change without notice WJ Communications, Inc x Phone 1-800-WJ1-4401 x FAX: 408-577-6621 x e-mail: sales@wj.com x W eb site: www.wj.com Page 1 of 3 May 2007 High Dynamic Range FET Mixer HMJ8 Typical Performance Data Specifications and information are subject to change without notice WJ Communications, Inc x Phone 1-800-WJ1-4401 x FAX: 408-577-6621 x e-mail: sales@wj.com x W eb site: www.wj.com Page 2 of 3 May 2007 High Dynamic Range FET Mixer HMJ8 Outline Drawing Product Marking The component will be marked with an “HMJ8” designator with a four-digit alphanumeric lot number XXXX. Tape and reel specifications for this part are located on the website in the “Application Notes” section. HMJ8 US PAT. 5732345 mm inch ESD Information ESD Rating: Value: Test: Standard: ESD Rating: Value: Test: Standard: Class 2 Passes at 2000 V Human Body Model (HBM) JEDEC Standard JESD22-A114 Class IV Passes at 2000 V Charged Device Model (CDM) JEDEC Standard JESD22-C101 Mounting Config. Notes 1. Ground vias are critical for thermal and RF grounding considerations. 2. A minimum of 28 ground vias are required for 14 mil FR4 boards. 3. If your PCB design rules allow, ground vias should be placed under the land pattern for better RF performance. Otherwise ground vias should be placed as close to the land pattern as possible. 4. Trace width depends on the PCB material. Land Pattern / Mounting Configuration 6.6 .260 11.94 .470 Specifications and information are subject to change without notice WJ Communications, Inc x Phone 1-800-WJ1-4401 x FAX: 408-577-6621 x e-mail: sales@wj.com x W eb site: www.wj.com Page 3 of 3 May 2007