SP8604

Obsolescence Notice This product is obsolete. This information is available for your convenience only. For more information on Zarlink’s obsolete products and replacement product lists, please visit http://products.zarlink.com/obsolete_products/ THIS DOCUMENT IS FOR MAINTENANCE PURPOSES ONLY AND IS NOT RECOMMENDED FOR NEW DESIGNS ADVANCE INFORMATION DS3658-1·2 SP8602 500MHz42 SP8604 300MHz42 The SP8602 and SP8604 are emitter coupled logic dividers which feature ECL10K compatible outputs when used with external pulldown resistors. The inputs are AC coupled. VEE (CASE) FEATURES s ECL Compatible Outputs s AC-Coupled Inputs (Internal Bias) QUICK REFERENCE DATA OUTPUT 78 OUTPUT 6 54 VCC (0V) NC 3 1 2 CLOCK INPUT CLOCK INPUT s Supply Voltage: 25·2V s Power Consumption: 85mW s Temperature Range: 255°C to 1125°C (A Grade) 230°C to 170°C (B Grade) INTERNAL BIAS DECOUPLING CM8 Fig. 1 Pin connections - bottom view ABSOLUTE MAXIMUM RATINGS Supply voltage, VEE Output current Storage temperature range Max. junction temperature Max. clock input voltage 28V 10mA 265°C to 1150°C 1175°C 2·5V p-p ORDERING INFORMATION SP8602 A CM SP8602 B CM SP8604 A CM SP8604 B CM 5962-92059 (SMD) (SP8602) INTERNAL BIAS DECOUPLING 3 VCC (0V) 5 CLOCK INPUT CLOCK INPUT 1 2 DIVIDE BY 2 6 7 OUTPUT OUTPUT 8 VEE Fig. 2 Functional diagram SP8602/4 ELECTRICAL CHARACTERISTICS Unless otherwise stated, the Electrical Characteristics are guaranteed over specified supply, frequency and temperature range Supply voltage, VCC = 0V, VEE = 25·2V 6 0·25V Temperature, TAMB = 255°C to 1125°C (A Grade), 230°C to 170°C (B Grade) Value Characteristic Maximum frequency (sinewave input) Minimum frequency (sinewave input) Power supply current Output low voltage Output high voltage Minimum output swing Symbol fMAX fMIN IEE VOL VOH VOUT 21·8 20·85 400 Min. 500 300 40 18 21·4 20·7 Max. Units MHz MHz MHz mA V V mV Type SP8602 SP8604 Both Both Both Both Both Conditions Input = 400-800mV p-p Input = 400-800mV p-p Input = 400-800mV p-p VEE = 25·2V, outputs unloaded VEE = 25·2V VEE = 25·2V VEE = 25·2V Notes 3 3 NOTES 1. The temperature coefficients of VOH = 11·63mV/°C, and VOL = 10·34mV/°C but these are not tested. 2. The test configuration for dynamic testing is shown in Fig.5. 3. Tested at 25°C only. SP8604 INPUT AMPLITUDE (mV p-p) 1000 800 600 400 200 0 0 SP8602 TAMB = 255°C TO 1125°C (A GRADE) TAMB = 230°C TO 170°C (B GRADE) GUARANTEED * OPERATING WINDOW * Tested as specified in table of Electrical Characteristics 100 200 300 INPUT FREQUENCY (MHz) 400 500 Fig. 3 Typical input characteristics of SP8602 and SP8604 j1 j 0.5 j2 j 0.2 j5 0 0.2 0.5 1 2 5 50 100 2j 5 2j 0.2 200 300 500 400 2j 0.5 2j 1 2j 2 Fig. 4 Typical input impedance. Test conditions: supply voltage = 25·2V, ambient temperature = 25°C, frequencies in MHz, Impedances normalised to 50Ω 2 SP8602/4 OPERATING NOTES 1. The clock inputs (pins 1 and 2) can be driven single ended or differentially and should be capacitively coupled to the signal source. The input signal path is completed by connecting a capacitor from the internal bias decoupling, pin 3, to ground. 2. In the absence of a signal the device will self-oscillate. If this is undesirable, it may be prevented by connecting a 15kΩ resistor from the unused input to VEE. This will reduce the input sensitivity by approximately 100mV. 3. The circuit will operate down to DC but slew rate must be better than 100V/µs. 4. The outputs are compatible with ECLII. There is an internal load of 4kΩ on each output. The outputs can be interfaced to ECL10K by the addition of 1·5kΩ pulldown resistors from the outputs to VEE to increase output voltage swing. 5. Input impedance is a function of frequency, See Fig. 4. 6. All components should be suitable for the frequency in use. 20 TO SAMPLING SCOPE FROM GENERATOR INPUT 1 FROM GENERATOR INPUT 2 33 TO SAMPLING SCOPE 33 20 1n 33 33 1n 1n 1 1n 3 2 5 6 450 450 10n 10n TO SAMPLING SCOPE DUT 8 7 3·5k 3·5k VEE Fig. 5 Test circuit 1n INPUT 1 5 6 ECL OUTPUT 440 440 DIVIDE BY 2 7 15k 1n 2 BIAS 4k 4k 1·5k 8 VEE 1n 1·5k Fig. 6 Typical application showing interfacing 3 SP8602/4 PACKAGE DETAILS Dimensions are shown thus: mm (in). 4·19/4·70 (0·165/0·185) 12·70/14·28 (0·500/0·570) 812 7 3 6 54 45° 4·83/5·33 P.C.D. (0·190/0·210) 8·63/9·39 8·00/8·51 (0·315/0·335) (0·340/0·370) 0·41/0·53 (0·016/0·021) 0·25/1·02 (0·010/0·040) NOTES 1. Controlling dimensions are inches. 2. This package outline diagram is for guidance only. Please contact your GPS Customer Service Centre for further information. 8-LEAD METAL CAN - CM8 HEADQUARTERS OPERATIONS GEC PLESSEY SEMICONDUCTORS Cheney Manor, Swindon, Wiltshire SN2 2QW, United Kingdom. Tel: (0793) 518000 Fax: (0793) 518411 GEC PLESSEY SEMICONDUCTORS P.O. Box 660017 1500 Green Hills Road, Scotts Valley, CA95067-0017 United States of America. Tel (408) 438 2900 Fax: (408) 438 5576 CUSTOMER SERVICE CENTRES q FRANCE & BENELUX Les Ulis Cedex Tel: (1) 64 46 23 45 Fax : (1) 64 46 06 07 q GERMANY Munich Tel: (089) 3609 06-0 Fax : (089) 3609 06-55 q ITALY Milan Tel: (02) 66040867 Fax: (02) 66040993 q JAPAN Tokyo Tel: (3) 5276-5501 Fax: (3) 5276-5510 q NORTH AMERICA Scotts Valley, USA Tel: (408) 438 2900 Fax: (408) 438 7023. q SOUTH EAST ASIA Singapore Tel: (65) 3827708 Fax: (65) 3828872 q SWEDEN Stockholm Tel: 46 8 702 97 70 Fax: 46 8 640 47 36 q UK, EIRE, DENMARK, FINLAND & NORWAY Swindon Tel: (0793) 518510 Fax : (0793) 518582 These are supported by Agents and Distributors in major countries world-wide. © GEC Plessey Semiconductors 1994 Publication No. DS3658 Issue No. 1.2 March 1994 This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves the right to alter without prior knowledge the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request. 4 For more information about all Zarlink products visit our Web Site at w ww.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request. Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE