AZ830P2-2C-9DSE

AZ830P POLARIZED DIP RELAY BISTABLE (LATCHING) FEATURES • • • • • • • • • High sensitivity, 90 mW pickup Low profile DIP package Meets FCC Part 68.302 1500 V lightning surge Meets FCC Part 68.304 1000 V dielectric Epoxy sealed DC coils to 48 VDC High switching capacity, 60 W, 125 VA Fits standard 16 pin IC socket UL file E43203; CSA file LR 36664 GENERAL DATA CONTACTS Arrangement Ratings DPDT (2 Form C) Bifurcated crossbar contacts Resistive load: Max. switched power: 60 W or 125 VA Max. switched current: 2 A Max. switched voltage: 150 VDC or 300 VAC Rated Load UL Material 2 A at 30 VDC 1 A at 120 VAC Silver alloy, gold clad. Silver palladium, gold clad available upon request (not recommended for current greater than 1 Amp). < 50 milliohms initially Life Expectancy Mechanical Electrical Set Time (typical) Reset Time (typical) Capacitance Minimum operations 1 x 108 1 x 105 at 2 A, 30 VDC or 1 A, 125 VAC 2 x 106 at 1 A, 30 VDC or .5 A, 125 VAC 3 ms at nominal coil voltage 3.5 ms at nominal coil voltage Contact to contact: 1.0 pF Contact set to contact: 1.0 pF Contact to coil: 2.0 pF At 10 mA contact current 1.5 ms at operate N.O. side 2.5 ms at operate N.C. side 1500 Vrms contact to coil 1000 Vrms between contact sets 1000 Vrms across contacts Meets FCC Part 68.302 lightning surge Meets FCC Part 68.304 V dielectric 1000 megohms min. at 20°C, 500 VDC, 50% RH At nominal coil voltage Standard: -40°C (-40°F) to 85°C (185°F) Sensitive: -40°C (-40°F) to 95°C (203°F) Both: -40°C (-40°F) to 105°C (221°F) 0.062" (1.5 mm) DA at 10–55 Hz 40 g P.B.T. polyester Tinned copper alloy, P.C. 270°C (518°F) 5 seconds 80°C (176°F) 30 seconds 5 grams Bounce (typical) Dielectric Strength (at sea level) Resistance COIL (Polarized) Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature Standard coil: 176 mW Sensitive coil: 90 mW 1.2 W at 20°C (68°F) ambient Standard: 38°C (68°F) at nominal coil voltage Sensitive: 21°C (38°F) at nominal coil voltage Max. 115°C (239°F) Shock Enclosure Terminals Max. Solder Temp. Max. Solder Time Max. Solvent Temp. Max. Immersion Time Weight Insulation Resistance Ambient Temperature Operating Storage Vibration NOTES 1. 2. 3. 4. All values at 20°C (68°F). Relay may pull in with less than “Must Operate” value. Relay has fixed coil polarity. Relay adjustment may be affected if undue pressure is exerted on relay case. 5. For complete isolation between the relay’s magnetic fields, it is recommended that a .197" (5.0 mm) space be provided between adjacent relays. 6. Specifications subject to change without notice. ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2003-04-08 Junkersstrasse 3, D-82178 Puchheim, Germany AZ830P RELAY ORDERING DATA STANDARD RELAYS COIL SPECIFICATIONS Nominal Coil VDC 5 6 9 12 24 48 5 6 9 12 24 48 Max. Continuous VDC 7.5 9.0 13.5 18.0 36.0 72.0 11.0 13.0 19.5 26.0 53.0 106.0 Coil Resistance ± 10% 69.4 100 225 400 1,600 6,400 139 200 450 800 3,200 12,800 Set Reset VDC 3.5 4.2 6.3 8.4 16.8 33.6 3.5 4.2 6.3 8.4 16.8 33.6 Maximum Switching Capacity 10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 ORDER NUMBER* AZ830P2–2C–5DE AZ830P2–2C–6DE Current AZ830P2–2C–9DE AZ830P2–2C–12DE AZ830P2–2C–24DE AZ830P2–2C–48DE AZ830P2–2C–5DSE AZ830P2–2C–6DSE AZ830P2–2C–12DSE AZ830P2–2C–24DSE AZ830P2–2C–48DSE AZ830P2–2C–9DSE 1.0 .9 .8 .7 .6 .5 .4 .3 .2 AC Resistive Load DC Resistive Load SENSITIVE RELAYS Voltage * Add suffix “A” for silver palladium gold clad contacts. MECHANICAL DATA .788 (20.0) .390 (9.9) Coil Temperature Rise Standard 110 Full Load 100 Coil Temperature Rise ¡C .386 .366 (9.8) (9.3) 90 80 70 60 50 40 30 20 10 60% 80% 100% 120% 140% 160% 180% No Load .138 (3.5) .012 ± .005 (0.3 ± 0.13) TYP .044 (1.1) .100 (2.54) .200 (5.07) .200 (5.07) .200 (5.07) (.024 ± .005) (0.6 ± 0.13) TYP PC BOARD LAYOUT 0.03 DIA (0.8) (10 HOLES) .044 (1.1) REF Percent of Nominal Coil Voltage Sensitive 60 .044 (1.1) REF Coil Temperature Rise˚C 50 Full Load No Load 40 Viewed toward terminals TWO COIL LATCHING WATCH FOR POLARITY 0.1 (2.54) 30 WIRING DIAGRAM 8 Diagrams show the “reset” position before energized with polarity as shown 20 1 + 2 + 4 6 10 60% 80% 100% 120% 140% 160% 180% Percent of Nominal Coil Voltage – 16 – 15 13 11 9 Viewed toward terminals Set Reset Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2003-04-08 Junkersstrasse 3, D-82178 Puchheim, Germany 1000 100 10 .1 50 60 70 80 90 400 500 600 700 800 900 20 30 40 200 300