RYN0.50BK

ADVANCED ENGINEERING ADVANCED ENGINEERING Technical Data Sheet Technical Data Sheet Put-Ups F  AR 25 Approved Nominal Size U  ltra-Light Weight 1/8” 1/4” 1/2” 3/4” 1 1/4” 1 3/4” 2” 10 Mil 1/8” H  ighly Wear Resistant E  xpands Up To 150% R  esists Acids, Bases, Solvents And Fuels C  ut And Abrasion Resistant Expansion Range Part # Min Max Bulk Spool Shop Spool Available Colors Lbs/ 100’ RYN0.13 RYN0.25 RYN0.50 RYN0.75 RYN1.25 RYN1.75 RYN2.00 3/32” 1/8” 1/4” 1/2” 3/4” 1 1/4” 1 5/16” 1/4” 3/8” 3/4” 1 1/4” 1 3/4” 2 1/2” 2 3/8” 1,000’ 1,000’ 500’ 250’ 250’ 200’ 200’ 225’ 200’ 100’ 75’ 50’ 50’ 50’ 2 2 2 2 2 2 2 0.21 0.36 0.59 0.75 1.30 1.60 2.00 RZH0.13NT 1/8” 9/32” 1,000’ 225’ NT 0.26 Ultra Lightweight High-Temp Tolerant And Virtually Impervious To Chemical Degradation Cut Cleanly Hot Knife Material Polyethylene Sulphide Grade RYN Monofilament Diameter .008” FLEXO PPS expandable sleeving is used in high temperature, flame resistant wire harnesses and cable assemblies. Flexo PPS is an extremely lightweight sleeving, resistant to high temperatures and virtually impervious to solvents. This sleeving is ideal for aerospace, telecom and military applications and meets many engineering goals including; chemical resistance, high temperature stability, zero moisture absorption, excellent dimensional stability and ultra-low wear. Colors Available: 2 = NT and BK Flexo PPS is braided from 8 mil flame resistant PolyPhenylene Sulfide (PPS) monofilament fibers. PPS offers the broadest resistance to chemicals of any advanced engineering plastic. The material resists all known solvents below 392°F (200°C) and is inert to steam, strong bases, fuels and acids. A true aerospace material, Flexo PPS is ideal in satellite applications where weight and stability are of primary importance. Colors Available: Drawing Number TF001RY-WD Natural (NT) and Black (BK). www.techflex.com 1 (833) SLEEVING • (973) 300-9242 • fax: (973) 300-9409 104 Demarest Road • Sparta, NJ 0787 UL94 V-O FAR-25 ADVANCED ENGINEERING ADVANCED ENGINEERING Technical Data Sheet Technical Data Sheet Melt Point ASTM D-2117 ABRASION Medium Rating______________ FAR 25, UL94 V-O Taber 5150 Calibrase H-18 Abrasion Test Load 500g Room Temperature 71°F Humidity 59% Very Visible Wear And Several Filaments Broken 100 Test Cycles Wear Continues 150 Test Cycles Material Destroyed 450 Test Cycles Pre-Test Weight 3,079.2 mg Post-Test Weight 2,614.9mg Test End Loss Of Mass Point Of Destruction 464.3 mg Mil-I-23053 392°F (200°C) Minimum Continuous -94°F (-70°C) Abrasion Test Machine Abrasion Test Wheel Maximum Continuous CHEMICAL RESISTANCE 1=No Effect 2=Little Effect 3=Affected 4=More Affected 5=Severely Affected Aromatic Solvents_________________ 1 Aliphatic Solvents__________________ 1 Chlorinated Solvents_______________ 1 Weak Bases_______________________ 1 Salts_____________________________ 1 Strong Bases______________________ 1 Salt Water 0-S-1926________________ 1 Hydraulic Fluid MIL-H-5606__________ 1 Lube Oil MIL-L-7808________________ 1 De-Icing Fluid MIL-A-8243___________ 1 Strong Acids______________________ 1 Strong Oxidants___________________ 1 Esters/Ketones____________________ 1 UV Light_________________________ 1 Petroleum________________________ 1 Fungus ASTM G-21_________________ 1 Halogen Free____________________ Yes RoHS___________________________ Yes SVHC______________________________ PHYSICAL PROPERTIES Monofilament Diameter________ .008” ASTM D-204 Flammability Rating___ FAR 25, UL94 V-O Recommended Cutting_____ Hot Knife Colors___________________________ 2 Wall Thickness__________________ .024” Tensile Strength (Yarn)____________ 6.1 ASTM D-2256 Lbs Specific Gravity ASTM D-792_____ 1.37 Moisture Absorption_____________ .02 % ASTM D-570 Hard Vacuum Data__________________ ASTM E-595 at 10-5 torr TML___________________________.08 CVCM_________________________ .00 WVR___________________________ .04 Smoke D-Max_____________________ ASTM E-662 Outgassing____________________Low Oxygen Index____________________40 ASTM D-2863 © 2021 Techflex® - Any unauthorized reproduction, in whole or part, in any medium whatsoever, without the express written permission of Techflex® is strictly forbidden. Techflex® product names and logos are registered trademarks of Techflex®, unless otherwise attributed. The contents and illustrations contained herein are believed to be reliable. Techflex® makes no warranties as to their accuracy or completeness and disclaims any liability in connection with their use. Techflex’s® only obligations are those in standard terms of sale for these products and Techflex® will not be liable for any consequential or other damages arising due to misuse of these products or typographical errors or omissions. 06/18 Users should make their own evaluation to determine the suitability of these products for their unique and specific applications. www.techflex.com Abrasion Resistance FLAMMABILITY 545°F (285°C)