3M™ Mini D Ribbon (MDR) Connectors
.050” Surface Mount Right Angle Die-Cast Receptacle – Shielded
102 Series
• Rugged die-cast body resists tipping during automated soldering operations • Wiper-on-wiper contact for reliable repetitive plugging • Ultra-low signal skew for high data rate transmission • Interface latch design for connection stability • Suitable for thumbscrew attach (see TS-0142 for available hardware) • MDR digital LCD interface as a 20 or 26 contact connector • Camera Link® interface as a 26 contact connector • Contacts: 14, 20, 26, 40 and 50 • See Regulatory Information Appendix (RIA) for chemical compliance information
Date Modified: December 20, 2007
TS‑2242‑A Sheet 1 of 3
Physical
Body Material: Flammability: Alignment Plate Material: Flammability: Contact Material: Underplating: Wiping Area Plating: Solder Tail Plating: Shroud Material: Plating: Lock Stand Material: Plating: Glass Reinforced Polyester (PCT), Natural Color UL 94V-0 LCP, Natural Color UL 94V-0 Copper Alloy 80 µ” [2 µm] Nickel See Ordering Information Flash Gold over Nickel (RIA E1 & C1 apply) Steel Nickel Zinc Alloy Nickel
Electrical
Current Rating: 1 A Insulation Resistance: >5 x 108 Ω at 500 VDC Withstanding Voltage: 500 VRMS for 1 minute
Environmental
Temperature Rating: -55 °C to +85 °C Process Rating: 240°C- 250°C peak temperature for less than 10 secs., 220°C soldering for 30 – 60 secs. after 150°C - 180°C preheat for 90 –120 secs. (reflow two times)
UL File No.: E68080 3 Interconnect Solutions
http://www.3M.com/interconnects/
Camera Link® is a trademark of Automated Imaging Assocition
3M is a trademark of the 3M Company
For technical, sales or ordering information call 800-225-5373
3M™ Mini D Ribbon (MDR) Connectors
.050” Surface Mount Right Angle Die-Cast Receptacle — Shielded
DIM. A DIM. B DIM. C 0.635 [.025] M2.5 0.25 [.010] T TAIL COPLANARITY 0.00 TO 0.10 9.35 [.368] 9 .1 [.36] MARK PIN MARK PIN
102 Series
1.20 [.047]
11.5 [.45]
2 .9 [.11]
16.7 [.66]
4 .8 [.19]
3.5 [.14]
DIM. D DIM. E
T
7 .2 [.28] T-T
15°
9.1 [.36]
0.3 [.01]
N 1 .9 [.07]
FLAT FIXTURE SURFACE MARK PIN 1.27±0.10 [.050±0.004]
DETAIL-N
DIM. G DIM. H
Contact Quantity 14 20 26 40 50
DIM A
29.5 (1.16) 33.3 (1.31) 37.2 (1.46) 46.1 (1.81) 52.4 (2.06)
DIM B
23.64 (.931) 27.45 (1.081) 31.26 (1.231) 40.15 (1.581) 46.50 (1.831)
DIM C
8.255 (.325) 12.065 (.475) 15.875 (.625) 24.765 (.975) 31.115 (1.225)
DIM D
17.1 (.67) 21.0 (.83) 24.8 (.98) 33.7 (1.33) 40.0 (1.57)
DIM E
19.5 (.77) 23.4 (.92) 27.2 (1.07) 36.1 (1.42) 42.4 (1.67)
DIM F
12.6 (.50) 16.4 (.65) 20.2 (.80) 29.1 (1.15) 35.5 (1.40)
DIM G
7.62 (.300) 11.43 (.450) 15.24 (.600) 24.13 (.950) 30.48 (1.200)
DIM H
12.70 (.500) 16.51 (.650) 20.32 (.800) 29.21 (1.150) 35.56 (1.400)
0.00 TO 0.10 [.000 TO .004]
M2.5
4.8 [.19]
DIM. F
MARK PIN
2 .8 [.11] 6.3 [.25]
4 .7 5 [.187]
10.0 [.39]
mm (inch) Tolerance Unless Noted .0 mm ±.3 .00 .000 ±.15 ±.150
( ) Dimensions used for Reference Only
TS‑2242‑A Sheet 2 of 3
Ordering Information
Contact Quantity See Table
102XX-1S10 PX
Wiping Area Plating: L = 8 µ” min. Gold with Lubricant Treatment E = 20 µ” min. Gold C = 30 µ” min. Gold
3 Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of the 3M Company
For technical, sales or ordering information call 800-225-5373
3M™ Mini D Ribbon (MDR) Connectors
.050” Surface Mount Right Angle Die-Cast Receptacle — Shielded
7.24 [.285] Ø2.80+0.10 -0.00 Ø.110+.004 -.000
2.2225 REF [.0875]
102 Series
6.74 [.265] 3.84±0.10 [.151±.004] 3.00 [.118] 4.75 [.187] 2.00 [.079]
[
]
MARK PIN MARK PIN
1.00 [.039]
0.400±0.02 [.016±.001]
0.635±0.02 [.025±.001]
4.20 [.165]
DIM. K
DIM. M
DIM. L
DIM. J
[
Ø2.00+0.10 -0.00 Ø.079+.004 -.000
]
EDGE OF PWB PATTERN PROHIBITION AREA "LOCK STAND" MOUNTING AREA ONLY SOLDER PAD
0.50 TYP [.020]
7.20±0.15 [.283±.006]
2.90 REF [.114] 12.00 [.47]
4.94 REF [.195] 7.84±0.15 [.309±.006]
R1.50 [R.059]
DIM. P DIM. N 8.10±0.1 [.319±.004]
Recommended Board Layout
Viewed from Connector Side
Recommended Panel Cutout
Panel Thickness: 2.0 mm (.08 inch) Max.
Contact Quantity 14 20 26 40 50
DIM J
29.5 (1.16) 33.3 (1.31) 37.2 (1.46) 46.1 (1.81) 52.4 (2.06)
DIM K
23.64 (.931) 27.45 (1.081) 31.26 (1.231) 40.15 (1.581) 46.50 (1.831)
DIM L
12.70 (.500) 16.51 (.650) 20.32 (.800) 29.21 (1.150) 35.56 (1.400)
DIM M
8.255 (.325) 12.065 (.475) 15.875 (.625) 24.765 (.975) 31.115 (1.225)
DIM N
19.9 (.78) 23.8 (.94) 27.6 (1.09) 36.5 (1.44) 42.8 (1.69)
DIM P
23.64 ± .13 (.931) 27.45 ± .13 (1.081) 31.26 ± .13 (1.231) 40.15 ± .13 (1.581) 46.50 ± .13 (1.831)
mm (inch) Tolerance Unless Noted .0 mm ±.3 .00 .000 ±.05 ±.050
( ) Dimensions used for Reference Only
Note: The connector should be mounted to the panel and printed circuit board with screws. See TS-0142 for mounting hardware.
TS‑2242‑A Sheet 3 of 3
3 Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of the 3M Company
For technical, sales or ordering information call 800-225-5373
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/717/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217B-c
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under Item 6 of the Annex to the Directive. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below.
RIA-2217B-c
Appendix C3: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below.
Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3
3M Electronics Interconnect Products
6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3m.com/interconnects
Please recycle. Printed in USA. © 3M 2007. All rights reserved. RIA-2217B-c
3M is a trademark of 3M Company.
