10220-1S10PE

3M™ Mini D Ribbon (MDR) Connectors .050” Surface Mount Right Angle Die-Cast Receptacle – Shielded 102 Series • Rugged die-cast body resists tipping during automated soldering operations • Wiper-on-wiper contact for reliable repetitive plugging • Ultra-low signal skew for high data rate transmission • Interface latch design for connection stability • Suitable for thumbscrew attach (see TS-0142 for available hardware) • MDR digital LCD interface as a 20 or 26 contact connector • Camera Link® interface as a 26 contact connector • Contacts: 14, 20, 26, 40 and 50 • See the Regulatory Information Appendix (RIA) in the “RoHS compliance” section of www.3mconnector.com for compliance information Date Modified: October 27, 2010 TS‑2242-B Sheet 1 of 3 Physical Body Material: Flammability: Alignment Plate Material: Flammability: Contact Material: Underplating: Wiping Area Plating: Solder Tail Plating: Shroud Material: Plating: Lock Stand Material: Plating: Glass Reinforced Polyester (PCT), Natural Color UL 94V-0 LCP, Natural Color UL 94V-0 Copper Alloy 80 µ” [2 µm] Nickel See Ordering Information Flash Gold over Nickel (RIA E1 & C1 apply) Steel Nickel Zinc Alloy Nickel Electrical Current Rating: 1 A Insulation Resistance: >5 x 108 Ω at 500 VDC Withstanding Voltage: 500 Vrms for 1 minute Environmental Temperature Rating: -55 °C to +85 °C Process Rating: 240°C- 250°C peak temperature for less than 10 secs., 220°C soldering for 30 – 60 secs. after 150°C - 180°C preheat for 90 –120 secs. (reflow two times) UL File No.: E68080 3 Interconnect Solutions http://www.3Mconnector.com Camera Link® is a trademark of Automated Imaging Assocition 3M is a trademark of the 3M Company For technical, sales or ordering information call 800-225-5373 3M™ Mini D Ribbon (MDR) Connectors .050” Surface Mount Right Angle Die-Cast Receptacle — Shielded DIM. A DIM. B TAIL COPLANARITY 0.00 TO 0.10 9.35 [.368] 9.1 [.36] MARK PIN DIM. C 0.635 [.025] T 10.0 [.39] 2.9 [.11] 16.7 [.66] 11.5 [.45] DIM. D 3.5 [.14] 4.8 [.19] 1.20 [.047] MARK PIN 7.2 [.28] T DIM. E 4.75 [.187] 0.25 [.010] M2.5 102 Series T-T 4.8 [.19] 0.3 [.01] 9.1 [.36] 15° 0.00 TO 0.10 [.000 TO .004] MARK PIN DIM. F 2.8 [.11] 6.3 [.25] M2.5 FLAT FIXTURE SURFACE N 1.9 [.07] DIM. G DIM. H MARK PIN DETAIL-N 1.27±0.10 [.050±0.004] Contact Quantity DIM A DIM B DIM C DIM D DIM E DIM F DIM G DIM H 14 29.5 (1.16) 23.64 (.931) 8.255 (.325) 17.1 (.67) 19.5 (.77) 12.6 (.50) 7.62 (.300) 12.70 (.500) 20 33.3 (1.31) 27.45 (1.081) 12.065 (.475) 21.0 (.83) 23.4 (.92) 16.4 (.65) 11.43 (.450) 16.51 (.650) 26 37.2 (1.46) 31.26 (1.231) 15.875 (.625) 24.8 (.98) 27.2 (1.07) 20.2 (.80) 15.24 (.600) 20.32 (.800) 40 46.1 (1.81) 40.15 (1.581) 24.765 (.975) 33.7 (1.33) 36.1 (1.42) 29.1 (1.15) 24.13 (.950) 29.21 (1.150) 50 52.4 (2.06) 46.50 (1.831) 31.115 (1.225) 40.0 (1.57) 42.4 (1.67) 35.5 (1.40) 30.48 (1.200) 35.56 (1.400) Ordering Information http://www.3Mconnector.com Tolerance Unless Noted mm .0 .00 .000 ±.3 ±.15 ±.150 ( ) Dimensions used for Reference Only TS‑2242-B Sheet 2 of 3 102XX-1S10 PX Contact Quantity See Table 3 Interconnect Solutions mm (inch) Wiping Area Plating: L = 8 µ” min. Gold with Lubricant Treatment E = 20 µ” min. Gold 3M is a trademark of the 3M Company For technical, sales or ordering information call 800-225-5373 3M™ Mini D Ribbon (MDR) Connectors .050” Surface Mount Right Angle Die-Cast Receptacle — Shielded 7.24 [.285] 6.74 [.265] 3.84±0.10 [.151±.004] Ø2.80+0.10 -0.00 Ø.110+.004 -.000 [ ] 3.00 [.118] 0.400±0.02 [.016±.001] 2.2225 REF [.0875] 4.75 [.187] 2.00 [.079] 1.00 [.039] MARK PIN 0.635±0.02 [.025±.001] DIM. M Ø2.00+0.10 -0.00 Ø.079+.004 -.000 [ 4.20 [.165] ] EDGE OF PWB PATTERN PROHIBITION AREA 0.50 TYP [.020] DIM. L DIM. J MARK PIN DIM. K 102 Series "LOCK STAND" MOUNTING AREA ONLY SOLDER PAD 4.94 REF [.195] 7.20±0.15 [.283±.006] 2.90 REF [.114] 12.00 [.47] R1.50 7.84±0.15 [.309±.006] DIM. P DIM. N [R.059] 8.10±0.1 [.319±.004] Recommended Board Layout Recommended Panel Cutout Viewed from Connector Side Panel Thickness: 2.0 mm (.08 inch) Max. Contact Quantity DIM J DIM K DIM L DIM M DIM N DIM P 14 29.5 (1.16) 23.64 (.931) 12.70 (.500) 8.255 (.325) 19.9 (.78) 23.64 .13 (.931) 20 33.3 (1.31) 27.45 (1.081) 16.51 (.650) 12.065 (.475) 23.8 (.94) 27.45 .13 (1.081) 26 37.2 (1.46) 31.26 (1.231) 20.32 (.800) 15.875 (.625) 27.6 (1.09) 31.26 .13 (1.231) 40 46.1 (1.81) 40.15 (1.581) 29.21 (1.150) 24.765 (.975) 36.5 (1.44) 40.15 .13 (1.581) 50 52.4 (2.06) 46.50 (1.831) 35.56 (1.400) 31.115 (1.225) 42.8 (1.69) 46.50 .13 (1.831) mm (inch) Tolerance Unless Noted mm http://www.3M.com/interconnects/ .00 .000 ±.3 ±.05 ±.050 ( ) Dimensions used for Reference Only Note: The connector should be mounted to the panel and printed circuit board with screws. See TS-0142 for mounting hardware. 3 Interconnect Solutions .0 TS‑2242-B Sheet 3 of 3 3M is a trademark of the 3M Company For technical, sales or ordering information call 800-225-5373 Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.  3M Electronics Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3Mconnector.com Please recycle. Printed in USA. © 3M 2010. All rights reserved. RIA-2217B-E 3M is a trademark of 3M Company.