3M™ Shrunk Delta Ribbon (SDR) Cable Assembly
.80 mm Digital Camera Cable, PoCL Compatible, 26 position
1MD26-X5XX-00C-XXX
• Carries power in addition to signal to enable use in base
configuration Power over Camera Link® (PoCL)
applications
• Connects between Mini-Camera Link style (SDR) I/O
ports on PoCL Cameras and Camera Link style (MDR)
ports on PoCL framegrabbers
• Both straight and right angle cable exit available
• 3 shielded quads and 6 unshielded twisted pairs
• Entire cable bundle shielded with foil and braid for
additional signal protection
• Rugged ribbon type contact for reliable, repeatable
connectivity
• Thumbscrew retention
• EMI shielded end-to-end for reduced emissions
• See Regulatory Information Appendix (RIA) for chemical
compliance information
Date Modified: November 21, 2008
TS-2286-A
Sheet 1 of 4
Physical
Connector Contact Plating:
Wiping Area: 30 μ" [0.76 μm] Min. Gold (RIA E1 & C1 apply)
Underplating: 100 μ" [ 2.54 μm ] Nickel
Overmolded Shell:
Color: Black
Material: Polyvinyl Chloride (PVC)
Shell:
Color: Gray or Black
Material: Polyester Elastomer
Cable:
Color: Gray or Black
Jacket Material: Polyvinyl Chloride (PVC)
Flammability: AWM VW-1
Electrical
Voltage Rating:
Current Rating:
Insulation Resistance:
Withstanding Voltage:
Twisted Pairs
Cable Characteristic Impedence:
Conductor Size:
Skew (within pair):
Skew (Channel skew per chipset):
30 V
0.5 A
> 1 x 108 Ω at 100 VDC
125 VAC (RMS) for 1 minute
100 ± 10 Ω differential
28 AWG Stranded
50 ps/meter maximum
100 ps/meter maximum, 50 ps/meter maximum for 1MD26-R5XX-00C-XXX
Environmental
Temperature Rating: 0°C to +70°C
UL File No.: E86982
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
Camera Link is a certification mark of Automated Imaging Association.
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Shrunk Delta Ribbon (SDR) Cable Assembly
.80 mm Digital Camera Cable, PoCL Compatible, 26 position
1MD26-X5XX-00C-XXX
24.4
[0.96]
39.7
[1.56]
12.9
[0.51]
9.0
[0.35]
32.0
[1.26]
Cable Length
32.5
[1.28]
Figure 1
Straight SDR - Straight MDR
1MD26-X560-00C-XXX
39.7
[1.56]
24.4
[0.96]
16.7
[0.66]
12.9
[0.51]
18.2
[0.72]
9.5
[0.37]
mm
[Inch]
Tolerance Unless Noted
mm
0.0
0.00
±.1
±.01
[ ] Dimensions for Reference Only
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
30.7
[1.21]
Cable Length
32.5
[1.28]
Figure 2
Right-Angle SDR - Straight MDR
1MD26-X57X-00C-XXX
TS-2286-A
Sheet 2 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Shrunk Delta Ribbon (SDR) Cable Assembly
.80 mm Digital Camera Cable, PoCL Compatible, 26 position
1MD26-X5XX-00C-XXX
24.4
[0.96]
39.7
[1.56]
25.4
[1.00]
9.0
[0.35]
19.4
[0.76]
32.0
[1.26]
Cable Length
42.4
[1.67]
Figure 3
Straight SDR - Right-Angle MDR
1MD26-X58X-00C-XXX
14.0
[0.55]
mm
[Inch]
Tolerance Unless Noted
mm
0.0
0.00
±.1
±.01
[ ] Dimensions for Reference Only
Figure 4
1MD26-X576-00C-XXX
Figure 5
1MD26-X577-00C-XXX
Figure 6
1MD26-X586-00C-XXX
Figure 7
1MD26-X587-00C-XXX
TS-2286-A
Sheet 3 of 4
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Shrunk Delta Ribbon (SDR) Cable Assembly
.80 mm Digital Camera Cable, PoCL Compatible, 26 position
1MD26-X5XX-00C-XXX
Table 1
Wiring Chart
CN-1
CN-2
Connector
Position
Signal
2
X0-
15
X0+
3
X1-
1MD26-35XX00C-XXX Cable
Quad 1
1MD26-R5XX00C-XXX Cable
Quad 1
Signal
Connector
Position
X0-
25
X0+
12
X1-
24
16
X1+
X1+
11
4
X2-
X2-
23
X2+
10
Xclk-
22
17
X2+
5
Xclk-
18
Xclk+
Xclk+
9
6
X3-
X3-
21
19
X3+
X3+
8
7
SerTC+
SerTC+
20
20
SerTC-
SerTC-
7
8
SerTFG-
21
SerTFG+
9
CC1-
22
CC1+
10
CC2+
23
CC2-
11
CC3-
24
CC3+
12
CC4+
25
CC4-
1
+12V
Quad 2
Quad 3
Quad 3
Twisted Pair 1
Twisted Pair 1
Twisted Pair 2
Twisted Pair 2
Twisted Pair 3
Twisted Pair 3
Twisted Pair 4
Twisted Pair 4
Twisted Pair 5
Twisted Pair 5
SerTFG-
19
SerTFG+
6
CC1-
18
CC1+
5
CC2+
17
CC2-
4
CC3-
16
CC3+
3
CC4+
15
CC4-
2
+12V
1
Twisted Pair 6
Twisted Pair 6
+12V
26
Insulated Wire
Inner Shield
13
Insulated Wire
Inner Shield
26
+12V
13
Inner Shield
Drain Wire
14
Inner Shield
Drain Wire
Shell
Quad 2
Braid Shield
14
Shell
Ordering Information
Cable Type:
3: Standard (gray)
R: Flexible (black)
1MD26 - X5XX - 00C - XXX
Cable Exit Combination & Attachment Direction:
60: Straight discrete MDR backshell to a straight overmolded SDR (Figure 1)
76: Straight discrete MDR backshell to a R/A overmolded SDR with cable opposite position 1 (Figures 2 & 4)
77: Straight discrete MDR backshell to a R/A overmolded SDR with cable same side as position 1 (Figures 2 & 5)
86: R/A overmolded MDR with cable opposite position 1 to a straight overmolded SDR (Figures 3 & 6)
87: R/A overmolded MDR with cable same side as position 1 to a straight overmolded SDR (Figures 3 & 7)
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
Cable Length:
200 = 200 cm
500 = 500 cm
A00 = 1000 cm
Other lengths available by
special order.
Contact 3M for details.
TS-2286-A
Sheet 4 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC, as amended by EU Commission Decision 2005/717/EC, as amended by
EU Court of Justice Decision 2008/C 116/04
This product contains decaBDE in the insulating material in excess of the maximum concentration allowed for finished
products subject to EU RoHS that are placed on the EU market after June 30, 2008.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217B-E
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the
product or part does not contain any of the following substances in excess of the following maximum concentration values in any
homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated
diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or
polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217B-E
Appendix C3: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or
polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
3
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects
Please recycle. Printed in USA.
© 3M 2008. All rights reserved.
RIA-2217B-E
3M is a trademark of 3M Company.