3443-94

3M™ Locator Plate 3443-94 Instructions for the assembly of 3M™ Socket Connectors, .100" x .100" and .100" x .200" 1.0 General 3M™ Manual and Pneumatic Assembly Presses and accessory assembly equipment are recommended for the termination of 3M socket connectors. 3M assembly equipment is offered to reduce set-up time, to provide easy and fast assembly, and to reduce assembly error. All listed socket connectors use the 3M™ Locator Plate 3443-94 and the 3M™ Platen 3342-9. Shut height settings for the 3M™ Presses 3316 and 3640 use 12, for the 3M™ Press 3335 use 12 ½, the 3M™ Press 3830 is self-adjusting. .100" x .200" Backplane System .100” x .100” Grid System Contact Quantity 3M Part number Contact Quantity 3M Part Number 20 3575 6 3863 26 3501 8 3868 34 3310 10 3473 40 3318 14 3385 50 3307 16 3452 20 3421 24 3626 26 3399 30 3419 34 3414 36 9436 40 3417 44 9444 50 3425 60 3334 The 3M Locator Plate 3443-94 was designed to assemble 3M socket connectors and replaces plates 3443-54, 3443-60, and 3443-73. February 2013 78-9101-4339-1 3 2.0 Set-up procedures for sockets, cables and guides Adjustments to plate Standard flat cable Various adjustments are required to the locator plate, depending on which socket connector or cable is being assembled. 3M™ Locator Plate 3443-94 is the recommended assembly aid. (See Figure 1) To assemble standard flat cable, the cable width is guided between: • The narrow end guide area. • The side of the end guide with the viewing port feature. The Locator Plate 3443-94 can be used to assemble: • .100" x .100" and .100" x .200" socket connectors with and without the center bump feature. Ground plane cable To assemble ground plane cable, the cable width is guided between: • Socket connectors with standard flat cable and with ground plane cable. • The wide end guide area. End guide set-up • The side of the end guide that does not have the viewing port feature. To adjust the position of the end guide for the connector length position, lift the end guide up and move it to the left or right. Center bump feature The center bump connector does not require any special set-up procedure. The viewing port on each end guide must align with the appropriate connector conductor size. The connector conductor size is specified by the numbers on the respective labels. To adjust the end guide position for the .l00" x .100" or .l00" x .200" connector, lift and rotate the end guide 180° so that the viewing port points to the respective .100" x .100" or .l00" x .200" label guide. .100” x .100” Side Standard Cable Locating Edge Viewing Port Ground Plane Cable Locating Edge Locator Plate Positioning Hole .100” x .200” Side Figure 1 2 3.0 Shut height adjustment procedures The shut height setting is referenced in the .100" x .200" Backplane System Chart and .100" x .100" Grid System Chart on page l. Shut height settings are guidelines for proper termination depth. Press Shaft The shut height should be adjusted from the base before the 3M™ Locator Plate is put into place. The 3M™ Presses 3316 and 3640 are adjusted with a knob at the top of the press. The 3M™ Press 3335 is adjusted with the collar on the press shaft, and the 3M™ Press 3830 is self-adjusting. 3.1  lace the shut height gauge 3436-1D across P the base of the assembly press. Lower the handle of the press until the handle casting makes contact with the press casting. (See Figure 2) 3.2  etermine the type of assembly press you are D using: Assembly Press Casting Shut Height Gauge Figure 2 Locking Ring • With the Press 3335, lock the shut height adjustment collar toward the base of the press shaft. (See Figure 3a) • With the Presses 3316 and 3640 Presses, turn the shut height adjustment knob until the bottom of the press shaft contacts the desired position on the shut height gauge. (See Figure 3b) Shut Height Adjustment Collar Figure 3a 3.3  Install the locator plate and appropriate platen on the press. The platen should be positioned so that it is parallel with the connector body and cover. CW (Lower) CCW (Raise) Shut Height Adjustment Knob Figure 3b 3 4.0 Connector/cable assembly procedures 4.1 Grasp a socket cover strip between the thumb and forefinger of both hands, with the liner facing you. Rotate the outermost cover down against the adjacent cover on the strip, breaking it from the liner. Pull laterally away from the strip, leaving a clean adhesive edge on the removed cover. (See Figure 4) 4.2 Firmly press ribbed side of cable into alignment grooves on cover. The adhesive will help it stay in place. (See Figure 5) 4.3 Figure 4 Visually inspect to insure that: • Cable is properly aligned to cover grooves. • Cable end is flush with cover for end terminations, or perpendicular to cover for midspan terminations. 4.4 Place the cable/cover sub-assembly between the guides on the 3M™ Locator Plate, cover side down. (See Figure 6) 4.5 Orient and position connector body — contacts down over the cable/cover subassembly, engaging cover retainer devices with body slots. (See Figure 7) 4.6 Lower the assembly press handle fully to complete the connection. 4.7 Raise press handle and remove completed assembly. Visually inspect to insure that: • Cover is fully seated and parallel with the body. Figure 5 Figure 6 • Cable is properly aligned with the cover grooves. • Cover retaining devices are completely engaged with the body. Figure 7 Customer and Technical Service Within the U.S.: Customer Service: 800-225-5373 Technical Support: 512-984-6703 Outside of the U.S.: For customer service and technical support, please contact your local 3M Electronic Solutions Division representative. 3M is a trademark of 3M Company. Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. 3M’s product warranty is stated in its Product Literature available upon request. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 Electronic Solutions Division Interconnect Products 6801 River Place Blvd. Austin, TX 78726-9000 800-225-5373 www.3Mconnectors.com Please recycle. Printed in USA. © 3M 2013 78-9101-4339-1