929841-01-26-RA

3M™ Thru-Board Socket .100″ and .100″ × .100″ Straight, Solder Tails 929 Series 1/ 17 • 3-40 contacts on one row, 4-80 on two row • Single hole board preparation simplifies board layout • No solder mask preparation speeds manufacturing assembly • Top mounting allows single pass for wave soldering • See Regulatory Information Index (RIA) for chemical compliance information Physical T IN U Glass Filled Polyester (PET) UL 94V-0 Gray Copper Alloy 100 μ″ [ 2.54 μm ] Nickel See ordering information options for thickness N Insulation Material: Flammability: Color: Contact Material: Plating Underplating: Wiping Area: TS-0814-05 Sheet 1 of 2 E D Date Modified: March 15, 2007 Electrical C O Solder Tails: 100 μ″ [ 2.54 μm ] tin lead or 200 μ" [ 5.08μm ] matte tin Marking: None IS Current Rating: 2 A Insulation Resistance: > 1 × 109Ω at 500 VDC D Withstanding Voltage: 1000 VRMS at Sea Level Environmental -55°C to +105°C Process Rating: 260°C, (profile per J-STD-020C) Moisture Sensitivity Level: 1 (per J-STD-020C) Temperature Rating: UL File No.: E68080 3M Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ Thru-Board Socket .100″ and .100″ × .100″ Straight, Solder Tails 929 Series Contact Quantity Inch [mm] 1 Row 2 Row 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 04 06 08 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 Tolerance Unless Noted inch .0 .00 .000 ±.1 ±.01 ±.005 [ ] Dimensions for Reference Only Recommended Solder Flow Direction .040 Sq Typ [ 1.02 ] A 17 .100 [ 2.54 ] Recommended Solder Flow Direction .200 [ 5.08 ] .125 [ 3.18 ] .235 [ 5.97 ] .130 [ 3.30 ] .062 [ 1.57 ] .100 Ref [ 2.54 ] .025 X .010 Typ [ 0.64 X 0.25 ] .100 Ref [ 2.54 ] N .040 [ 1.02 ] ∅ .065 ± .005Typ .002 [ 1.65] C O .100 ± .003 [ 2.54 ] .085 Typ [ 2.16 ] Pad Size .100 ± .003 .075 Typ [ 1.91 ] Pad Size .160 [ 4.06 ] .060 [ 1.52 ] .040 [ 1.02 ] Integral Solder Mask Plugs (See Note 1) See Note 1 See Note 1 .075 Typ [ 1.91 ] Pad Size [ 2.54 ] IS .100 ± .003 [ 2.54 ] .125 ± .010 [ 3.18 ] .005 .015 [ 0.38 ] T IN U .09 Ref [ 2.3 ] +.010 -.005 E D .040 Sq Typ [ 1.02 ] 1/ .100 [ 2.54 ] A Recommended Mounting Hole Pattern ∅ .065 ± [ 1.65] .085 Typ [ 2.16 ] Pad Size .005 Typ .002 Dimension A +0.00 [ +0.00 ] -.025 [ -.064 ] 0.20 [ 5.08 ] 0.30 [ 7.62 ] 0.40 [ 10.16 ] 0.50 [ 12.70 ] 0.60 [ 15.24 ] 0.70 [ 17.78 ] 0.80 [ 20.32 ] 0.90 [ 22.86 ] 1.00 [ 25.40 ] 1.10 [ 27.94 ] 1.20 [ 30.48 ] 1.30 [ 33.02 ] 1.40 [ 35.56 ] 1.50 [ 38.10 ] 1.60 [ 40.64 ] 1.70 [ 43.18 ] 1.80 [ 45.72 ] 1.90 [ 48.26 ] 2.00 [ 50.80 ] 2.10 [ 53.34 ] 2.20 [ 55.88 ] 2.30 [ 58.42 ] 2.40 [ 60.96 ] 2.50 [ 63.50 ] 2.60 [ 66.04 ] 2.70 [ 68.58 ] 2.80 [ 71.12 ] 2.90 [ 73.66 ] 3.00 [ 76.20 ] 3.10 [ 78.74 ] 3.20 [ 81.28 ] 3.30 [ 83.82 ] 3.40 [ 86.36 ] 3.50 [ 88.90 ] 3.60 [ 91.44 ] 3.70 [ 93.98 ] 3.80 [ 96.52 ] 3.90 [ 99.06 ] 4.00 [ 101.60 ] D Notes: 1. It is recommended that the plated thru-hole on the ends be .062″ [1.57] to .063″ [1.60]. This will prevent the connector from floating during the wave soldering process. 2. Integral solder mask plugs are removed after soldering by using the 3M™ Hand Tool 929013 with the 3M™ Molded Head 929025-0X-XX or 3M™ Hand Tool 929012 with the 3M™ Press 929050. 3. Do not hand solder this connector because the solder heat and volume of solder cannot be adequately controlled. This wouldmake the integral plugs difficult or impossible to remove. 4. The connector should be flow soldered such that it enters the solder wave, end first (width). Ordering Information 929XXX-01-XX-XX Plating Options: 2 Row 1 Row 841 = Gold 842 = Gold Contact Quantity: (per row) see table 3M Interconnect Solutions http://www.3M.com/interconnects/ Gold Plating Thickness: 10 = Wiping Area 10 µ" [0.25 µm] gold with tin-lead tails (RIA E3 & C2 apply) 30 = Wiping Area 30 µ" [0.76 µm] gold with tin-lead tails (RIA E3 & C2 apply) RA = 10 µ" [0.25 µm] gold wiping area with matte tin tails (RIA E1 & C1 apply) RB = 30 µ" [0.76 µm] gold wiping area with matte tin tails (RIA E1 & C1 apply) TS-0814-05 Sheet 2 of 2 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS 17 Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. 1/ Appendix E2: European Union RoHS T IN U E D Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/ EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E3: European Union RoHS C O N Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. IS In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. Appendix E4: European Union RoHS D Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/17/EC. “RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. RIA-2217-A CHINA Appendix C1: China RoHS Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. Appendix C2: China RoHS 17 In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the Warranty stated below. 20 T IN U E D 1/ Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the product Warranty stated below. IS C O N Name and Content of Hazardous Substances or Elements Important Notice D All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of ninety (90) days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 800/225-5373 www.3M.com/interconnects RIA-2217-A © 3M 2007