9SR-BD6-ABD-1.00

Product Specifications | Aug 2019 78-5102-0262-1, Rev B 3M™ 25G SFP28 & 100G QSFP28 Direct Attach Copper Cable Assemblies, 1422, 1423, 9Q and 9S Series Scope This document summarizes test methods, test conditions, and product performance requirements for 3M™ 25G SFP28 and 100G QSFP28 Direct Attach Copper Cable Assemblies including straight, Y, and breakout assembly configurations. 1422, 1423, 9Q, and 9S Series. Reference Documents Note: Unless otherwise specified, latest edition of the reference documents applies. In the event of conflict between requirements of the references and 3M specification, 3M specification shall take precedence. Commercial standards, specifications and report EIA-364 EIA TS-1000.01 SFF-8436, SFF-8661 SFF-8432, SFF-8083 3M™ 100G Direct Attach Copper Cable Assemblies Literature Code 78-5100-2664-0 78-5100-2672-3 78-5100-2684-8 78-5100-2679-8 Series 1422/1423 9Q 9S 9S Document Title Customer Drawing, 3M™ 25G SFP28 Direct Attach Copper Cable Assemblies, 1422/1423 Series Customer Drawing, 3M™ 100G QSFP28 Direct Attach Copper Cable Assemblies, 9Q Series Customer Drawing, 3M™ 100G QSFP28 to 2x QSFP28 Direct Attach Copper Cable Assemblies, 9S Series Customer Drawing, 3M™ 100G QSFP28 to 4x SFP28 Direct Attach Copper Cable Assemblies, 9S Series 3M™ 25G & 100G Direct Attach Copper Cable Assemblies, 1422, 1423, 9Q and 9S Series Performance Testing Unless otherwise specified, all tests shall be performed on SFP28/QSFP28 headers mated to SFP28/QSFP28 sockets with 3M Twinax cable at conditions per EIA-364. Unless otherwise specified, all values and limits are typical of those obtained by qualification testing of the subject product. All specifications are subject to revision and change without notice from 3M. Ratings 3M™ 25G/100G SFP28/QSFP28 Direct Attach Copper Cable Assemblies, 142/9Q/9S Series Feature Impedance Value 100ohms Operating Temperature 0°C to 70°C Storage Temperature -20°C to 85°C Humidity 0% to 80% RH Halogen Free – CL2 cable only CL2 cable option only. Does not include connector ends. UL has tested cables to be Halogen Free per UL2885. UL PLCC file E118773. Materials 3M™ 25G/100G SFP28/QSFP28 Direct Attach Copper Cable Assemblies, 142/9Q/9S Series Connector Connector Connector Connector Connector Component Shell Pull Tab Latch Spring Paddle Card Cable Cable Cable Primary Cable EMI Shield Jacket Material Die Cast Zinc Thermoplastic Stainless Steel Stainless Steel Flame Retardant PCB with 0.73um (30u”) Au over 1.27um (50u”) Ni min mating pad finish. 100 Ohm differential PO insulators Copper Foil laminate Flame retardant PVC or Halogen Free material. See Technical Specification for details and ratings. Product Specifications | 78-5102-0262-1 Rev B 3M™ 25G & 100G Direct Attach Copper Cable Assemblies, 1422, 1423, 9Q and 9S Series Regulatory Compliance For regulatory information, visit 3M.com/regs or contact your 3M representative. See customer drawings for regulatory specifics on each connector. Electrical Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3M™ 25G/100G SFP28/QSFP28 Direct Attach Copper Cable Assemblies, 142/9Q/9S Series Description or Parameter Dielectric Withstanding Voltage Insulation Resistance Impedance Insertion Loss Diff to Common Mode Conv. Loss Units V DC Mega ohms ohm db db Values and Limits 300 >1000 100+/-5 > -22.48 Formula Requirement or Conditions EIA-364-20, Method B Subject a voltage of 300 VDC for 1 minute at sea level between adjacent contacts of mated and unmated connector assemblies. Measured between adjacent and opposing contacts with 300 V applied for 1 minute. Measurement of a differential pair SDD21 @ 12.89Ghz SCD21 – SDD21 Test Standard or Method EIA-364-20B EIA-364-21C IEEE8023bj IEEE8023bj IEEE8023bj Product Specifications | 78-5102-0262-1 Rev B 3M™ 25G & 100G Direct Attach Copper Cable Assemblies, 1422, 1423, 9Q and 9S Series Mechanical Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3M™ 25G/100G SFP28/QSFP28 Direct Attach Copper Cable Assemblies, 142/9Q/9S Series Description or Parameter QSFP28 Mating force QSFP28 Unmating force Units Newtons Values and Limits 40N Max. Newtons 30N Max. Newtons 18N Max. SFP28 Newtons 12.5N Max. EIA-364-13 Unmating force Latched plug retention force Refer to SFF8432 Spec. Tested without latch feature Newtons 90N Min. Refer to SFF8432 Spec. Tested with latch feature EIA-364-98 G Sec Pulse G 50 11ms half sine 3.10 EIA-364-27B Condition A Durability (preconditioning) NA Nil Mated connectors shall exhibit no damage. No significant change in SDD21 or SCD21SDD21. 3.10G RMS between 20 and 500 Hz at 15 minutes in each of 3 mutually perpendicular directions. No damage. No discontinuity longer than 1µsec allowed. No significant change in SDD21 or SCD21SDD21. Perform 50 unplug/plug cycles. No evidence of physical damage. Durability NA Nil Perform 250 unplug/plug cycles. No evidence of physical damage. EIA-364-09 Reseating NA Nil Perform 3 unplug/plug cycles. EIA-364-09 SFP28 Mating force Shock Vibration Requirement or Conditions Refer to SFF8436 Spec. Tested without latch feature Refer to SFF8436 Spec. Tested without latch feature Refer to SFF8432 Spec. Tested without latch feature Test Standard or Method EIA-364-13 EIA-364-13 EIA-364-13 EIA-364-28 Condition VII D EIA-364-09 Product Specifications | 78-5102-0262-1 Rev B 3M™ 25G & 100G Direct Attach Copper Cable Assemblies, 1422, 1423, 9Q and 9S Series Environmental Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3M™ 25G/100G SFP28/QSFP28 Direct Attach Copper Cable Assemblies, 142/9Q/9S Series Description or Parameter Temperature Life (Thermal Aging) Units Requirement or Conditions Degrees C Hours Values and Limits 85 250 Thermal Shock HumidityTemperature Cycling Degrees C Cycles Degrees C % RH Cycles -55 & 85 10 65 to 25 80 to 50% 24 Corrosivity of Contacts (Humidity) Degrees C % RH Hours 40 90-96% 336 No physical abnormalities. No significant change in SDD21 or SCD21-SDD21. 1 cycle - 25°C, 80%RH to 65°C, 50RH to 25°C 80%. Ramp: 0.5 hour, Dwell: 1.0 hour. No significant change in SDD21 or SCD21SDD21 Steady stage Humidity. No significant change in SDD21 or SCD21-SDD21 No physical abnormalities. No significant change in SDD21 or SCD21-SDD21. Test Standard or Method EIA-364-17B Method A Condition 3B EIA-364-32A Condition I EIA-364-31B Condition B Method III 24 cycles. EIA-364-113A Condition I Qualification Test Groups and Sequenced Tests Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. 3M™ 25G/100G SFP28/QSFP28 Direct Attach Copper Cable Assemblies, 142/9Q/9S Series Test Description Visual SI (SDD21, SCD21-SDD21) Durability (preconditioning) Durability (full) Reseating Mechanical Shock Mechanical Vibration Temperature Life Humidity Temperature Cycling Thermal Shock Humidity, Corrosivity of Contacts Dielectric Withstand Voltage Mating Force Unmating Force Latched Plug Retention Force EIA 364 TP No. 18 09 09 09 27 28 17 31 32 1 0,5 1,4 2 Test Group 2 3 Test Sequence 0,17 0, 7 1,6 1,4,6 2 4 0,10 1,9 5 5 2 3 3 4 3 5 20 13 13 98 2,6 3,7 4,8 11 Product Specifications | 78-5102-0262-1 Rev B 3M™ 25G & 100G Direct Attach Copper Cable Assemblies, 1422, 1423, 9Q and 9S Series For regulatory information, visit 3M.com/regs or contact your 3M representative. Technical Information: The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. If the 3M Product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s option, replacement of the 3M product or refund of the purchase price. Product Use: Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user’s method of application. Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. 3M Electronics Materials Solutions Division Interconnect Products 13011 McCallen Pass Bldg. C Austin, TX 78753 www.3M.com/interconnect 3M is a trademark of 3M Company. Please recycle. ©3M 2019. All rights reserved. 78-5102-0262-1, Rev B Product Specifications | 78-5102-0262-1 Rev B