D3793-5002-AR

3M™ Four-Wall Header .100” × .100” Latch/Ejector, Straight and Right Angle D3000 Series • Military (with 3M’s 3518 & N3518 polarizing key) and centerbump polarization • Optional ejector latches • Mounting holes for securing header to board • Optional polarizing posts available • High temperature insulator suitable for “no lead” soldering operations • High temperature insulator in through-hole version suitable for “paste in hole” reflow soldering Date Modified: May 21, 2012  TS-2245-F Sheet 1 of 4 TS Physical -0 7 72 • RoHS Compliant. See the Regulatory Information Appendix (RIA) in the “RoHS compliance” section of www.3Mconnectors.com for compliance information (RIA E1 and C1 apply) Insulator: Material: High Temp Glass Filled Polyester (PCT) Color: Black (PCT) Contact: Material: Brass O SU BS O R L PE E T R E ED ED Plating: BY Flammability: UL 94V-0 Underplating: 50 -150 μ” [ 1.25 μm ] Ni Wiping Area: 15 µ” [0.381 µm] Gold Solder Tails: 40 - 120 μ” [ 1-3 μm ] Matte Tin Marking: 3M Logo, Part Identification Number and Orientation Triangle Electrical Current Rating: 5.00 A, 1 Contact Powered 3.00 A, 6 Contacts Powered 1.75 A, All Contacts Powered Rating Conditions: EIA-364-070 Method 2, 30°C maximum temperature rise, 20% derated. Reference appropriate 3M Product Specification for detailed current derating curves. Insulation Resistance: >1 × 109 Ω at 500 VDC Withstanding Voltage: 1,000 VRMS at Sea Level Environmental Temperature Rating: -55°C to +105°C Process Rating: 260°C, profile per J-STD-020C, single pass Moisture Sensitivity Level: 1 (per J-STD-020C) UL File No.: E68080 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ Four-Wall Header .100” × .100” Latch/Ejector, Straight and Right Angle D3000 Series -X2XX Header with Short Ejector/Latch for 3M Sockets without Strain Relief -X0XX Header without Latch Ejector .08 [2.0] -X3XX Header with Long Ejector/Latch for 3M Sockets with Strain Relief .08 [2.0] .573 ± .010 [ 14.55 ] .424 ± .010 [ 10.77 ] 1.07 Ref [27.2] .97 Ref [24.6] .46 Ref [11.7] .24 [6.1] .13 3.3 .30 [7.6] .100 2.54 .34 8.6 .25 6.4 REF. BY 2X O .100 [2.54] SEE NOTE #2 POSITION #1 B Dim. E CL .28 7.1 REF. TS .020 0.51 -0 7 D .100 2.54 72 .37 Ref [9.4] .025 ± .002 Sq Typ [ 0.64 ] O SU BS O R L PE E T R E ED ED “Y” F Typ Position 1 Orientation Triangle Section A-A (Straight) .025 ± .002 Sq Typ [ 0.64 ] .24 [6.1] F Typ CL .30 [7.6] “Y” Dim. E .049 Ref [1.24] .100 Ref [2.54] Section B-B .21 [5.3] Notch A (See Table 1 & Note1) Notch B (See Table 1) Notch C (See Table 1 & Note 1) .16 [4.1] A B .68 [17.3] .12 [3.0] .35 [8.9] .020 [0.51] 2X ø .100 [2.54] (See Note 2) A C B .197 [5.00] .20 [5.1] A (Right Angle) TS-2245-F Sheet 2 of 4 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ Four-Wall Header .100” × .100” Latch/Ejector, Straight and Right Angle D3000 Series Table 1 Dimensions Pin Qty 3M Part Number A B C D Polarizing Notches 06 3869 1.065 (27.05) 0.905 (22.99) 0.665 (16.89) 0.505 (12.83) B* 08 3889 1.165 (29.59) 1.005 (25.53) 0.765 (19.43) 0.605 (15.37) B* 10 3793 1.265 (32.13) 1.105 (28.04) 0.865 (21.97) 0.705 (17.91) BC 14 3314 1.465 (37.21) 1.305 (33.12) 1.065 (27.05) 0.905 (22.99) BC 16 3408 1.565 (39.75) 1.405 (35.66) 1.165 (29.59) 1.005 (25.53) ABC .0 20 3428 1.765 (44.83) 1.605 (40.74) 1.365 (34.67) 1.205 (30.61) ABC ± .1 24 3627 1.965 (49.91) 1.805 (45.82) 1.565 (39.75) 1.405 (35.69) ABC 26 3429 2.065 (52.45) 1.905 (48.36) 1.665 (42.29) 1.505 (38.23) ABC 30 3440 2.265 (57.53) 2.105 (53.44) 1.865 (47.37) 1.705 (43.31) ABC 34 3431 2.465 (62.61) 2.305 (58.52) 2.065 (52.45) 1.905 (48.39) ABC 40 3432 2.765 (70.23) 2.605 (66.14) 2.365 (60.07) 2.205 (56.01) ABC 50 3433 3.265 (82.93) 3.105 (78.84) 2.865 (72.77) 2.705 (68.71) ABC 60 3372 3.765 (95.63) 3.605 (91.54) 3.365 (85.47) 3.205 (81.41) ABC 64 3764 3.965 (100.71) 3.805 (96.62) 3.565 (90.55) 3.405 (86.49) ABC Table 2 -6XX2 Dim E Solder Tail for .062 [1.57] Thick PC Board .112 ± .010 [2.84] ø.106 [2.69] Dim F Diagonals .0245 ± .0005 .028 ± ..001 [0.622] or ø.116 [2.95] (See Note 2) .300 [7.62] Side to Side Stackability Dim G "Y" Ø.035 ±.003 [0.89] (See Note 3) ø.106 or ø.116 [2.95] [2.69] CL Position 1 .352 [8.94] Position 1 .029 [0.74] .100 ± .003 [2.54] .100 ± .003 [2.54] .0075 Ref [0.191] .41 (See Note 2) [10.4] Max to Edge of PCB Dim G for Daisy Chain CL .060 [1.52] .000 Dimension G Corner Radii [0.71] O SU BS O R L PE E T R E ED ED “Y” .00 ± .01 ± .005 [ ] Dimensions for Reference only Pin Cross Section Contact Tail BY -5XX2 Tolerance Unless Noted TS -0 77 2 * Available without center notch B. Contact 3M. 3M Part Number Suffix Inch (mm) .100 ± .003 [2.54] .100 ± .003 [2.54] B Recommended Mounting Hole Pattern (Straight) .232 [5.89] C Recommended Mounting Hole Pattern (Right Angle) Notes: 1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #3518 or #N3518). 2. Mounting hardware: From solder side of pc board use #4-24 thread cutting screw (3M Part # 3341-5) and .116 [2.95] dia mounting hole. For right angle version only, #2-56 bolt and nut (3M Part # 3341-6) with .106 [2.69] dia mounting hole may be used. See illustrations on page 4. 3. Contact your 3M sales representative for custom requirements. Ordering Information D3XXX - XX02AR Pin Configuration 5 = Right Angle Solder Tails 6 = Straight Solder Tails 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M Part Number (See Table 1) Latch/Ejector System 0 = No Latch/Ejector installed 2 = Short Roll Pin Latch/Ejectors 3 = Long Roll Pin Latch/Ejectors Tail 02 = for .062 [1.57] thick board TS-2245-F Sheet 3 of 4 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3M™ Four-Wall Header .100” × .100” Latch/Ejector, Straight and Right Angle , Accessories D3000 Series Part Customization This spec sheet details our standard offering. .321 [8.15] 3 2 0 1 -4 Note: Insert Post into one mounting hardware hole on bottom of header. Set post to protrude .115” [2.92] Polarizing Keys Polarizing Keys N3518 LCP N3518 3518 Latch Style Color N3505-31B Snap In Black High Temperature (PCT) N3505-2B N3505-3B Roll Pin Black • Selective pin removal (ATA or other compatability) Breakaway Tab BY Long Latch N3505-30B LCP PBT Dim A Blac k .02 Black Gray .02 .02 TS If ordering latches separately, please use the below chart Short Latch B la c k .100 Dia [2.54] • Snap-in style latch/ejectors in either short (N3XXXX5XXX) or long (N3XXX-X6XX) styles, may also be ordered separately, and are functional and dimensional equivalents to the -2 and -3 roll pin latches. High Temperature (PPA) LCP 72 • The -2 & -3 roll pin latches (may be ordered separately with roll pins included) Polarizing Post -0 7 3M has several capabilities that can provide a part tailored to your specific needs. Ask your 3M sales representative or customer service for more details. .09 [2.3] .34 Ref [8.6] .15 [3.8] A O SU BS O R L PE E T R E ED ED Note: #2216 B/A Scotchweld can be used to adhere keys. Mounting Hardware 3341-5 (Installed from bottom of board) 3341-6 (Must be inserted prior to latch on vertical headers) .50 [12.7] .31 [7.9] Panhead Thread Cutting Screw: #4-24 X 5/16” Type: USA Std BT, Federal BG Hex Head Bolt, Nut and Washer Bolt - #2-56 X 1/2” 3341-5 & 6 Material - Stainless Steel TS-2245-F Sheet 4 of 4 3 Electronic Solutions Division Interconnect Solutions http://www.3Mconnectors.com 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 72 -0 7 TS BY O SU BS O R L PE E T R E ED ED 3M is a trademark of 3M Company. Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3 3M Electronics Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3Mconnectors.com Please recycle. Printed in USA. © 3M 2012. All rights reserved. RIA-2217B-E