3M™ DIN C-Form Socket
.100” Standard Mount, Vertical, Solder Tail or Press-Fit Termination DIN
41612 Series
• Multi-pin count socket for VME, Multibus II, and VXI
backpanels
• Press-fit or solder tail terminals for PCB
• Expanded pin counts
• Optional retention clips
• Mates with C-form and R-form plugs
• See Regulatory Information Appendix (RIA) for chemical
compliance information
Date Modified: October 28, 2008
TS-1131-C
Sheet 1 of 4
Physical
Insulation:
Material: Glass Filled Polyester (PCT)
Flammability: UL94V-0
Color: Gray or Black
Contact:
Material: Copper Alloy
Plating:
Underplating: 50 μ” [ 1.27 μm ] Min. Nickel
Wiping Area: (See Ordering Information)
Termination Area: (See Ordering Information)
Marking: Part Number and Date Code
Electrical
Contact Resistance:
Current Rating:
Insulation Resistance:
Withstanding Voltage:
20 mΩ Max.
3.0 A @ 30°C T-rise above ambient
1 x 103 MΩ min. at 500 VDC
1 x 103 VAC for 1 minute
Environmental
Temperature Rating: -55°C to +125°C
Process Temperature Rating: 260°C (per J-STD-020C)
Moisture Sensitivity Level: 1 (per J-STD-020C)
UL File No.: E68080
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ DIN C-Form Socket
.100” Standard Mount, Vertical, Solder Tail or Press-Fit Termination DIN
41612 Series
A
POSITION A1
D
B
0.100
2.54
TYP.
0.230
5.84
0.335
8.51
0.417
10.59
0.039
.99
PRESS-FIT OR SOLDER TAIL
0.252
6.40
0.457
11.61
0.024 X 0.015
[.61 X .38 ]
0.100
2.54
TYP.
C
C TAIL LENGTH
0.024
.61
0.100
2.54
TYP.
E
0.150
3.80
Inch
[mm]
0.160
4.06
Au FINISH
Tolerance Unless Noted
.0
Inch
± .1
.00
.000
± .01 ± .005
Feed/Thru Wire Strap W, PW1 and
PW2 with RR and GG30 Finish
(Au both ends)
[ ] Dimensions for
Reference only
Ordering Information
DIN-XXX CS X-XXX-XXXX
Contact Quantity
See Table 1
Contact Loading:
A = A Row only
B = Rows A & C Filled
C = Rows A, B, & C Filled
D = Rows A & B Filled
E = B Row only
Plating and Insulating Color Options:
See Table 3
Termination Options:
See table 2
TS-1131-C
Sheet 2 of 4
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ DIN C-Form Socket
.100” Standard Mount, Vertical, Solder Tail or Press-Fit Termination DIN
41612 Series
Table 1
Contact Quantity
Load Pattern
A
B
D
E
016
032
048
32
016
032
064
096
064
032
040
080
120
080
040
050
100
150
100
050
A
B
C
D
E
A
B
C
D
E
A
B
C
D
E
A
B
C
D
E
2.140 [54.36]
2.140 [54.36]
2.140 [54.36]
2.140 [54.36]
2.140 [54.36]
3.740 [95.00]
3.740 [95.00]
3.740 [95.00]
3.740 [95.00]
3.740 [95.00]
4.540 [115.32]
4.540 [115.32]
4.540 [115.32]
4.540 [115.32]
4.540 [115.32]
5.540 [140.72]
5.540 [140.72]
5.540 [140.72]
5.540 [140.72]
5.540 [140.72]
1.746 [44.35]
1.746 [44.35]
1.746 [44.35]
1.746 [44.35]
1.746 [44.35]
3.346 [84.99]
3.346 [84.99]
3.346 [84.99]
3.346 [84.99]
3.346 [84.99]
4.146 [105.31]
4.146 [105.31]
4.146 [105.31]
4.146 [105.31]
4.146 [105.31]
5.146 [130.71]
5.146 [130.71]
5.146 [130.71]
5.146 [130.71]
5.146 [130.71]
1.943 [49.35]
1.943 [49.35]
1.943 [49.35]
1.943 [49.35]
1.943 [49.35]
3.543 [89.99]
3.543 [89.99]
3.543 [89.99]
3.543 [89.99]
3.543 [89.99]
4.343 [110.31]
4.343 [110.31]
4.343 [110.31]
4.343 [110.31]
4.343 [110.31]
5.343 [135.71]
5.343 [135.71]
5.343 [135.71]
5.343 [135.71]
5.343 [135.71]
1.500 [38.10]
1.500 [38.10]
1.500 [38.10]
1.500 [38.10]
1.500 [38.10]
3.100 [78.74]
3.100 [78.74]
3.100 [78.74]
3.100 [78.74]
3.100 [78.74]
3.900 [99.06]
3.900 [99.06]
3.900 [99.06]
3.900 [99.06]
3.900 [99.06]
4.900 [124.46]
4.900 [124.46]
4.900 [124.46]
4.900 [124.46]
4.900 [124.46]
Table 2
SOLDER TERMINATION OPTION No
DIM “C” in (mm)
Comments
R1L
R3L
S1 contact thickness (solder tail) = 25mil
S1L contact thickness (solder tail) =14mil
S3L
W
0.157 (3.99)
0.090 (2.29)
0.157 (3.99)
0.157 (3.99)
0.090 (2.29)
0.512 (13.00)
with retention clips
with retention clips
no retention clips
no retention clips
no retention clips
wire wrap
PRESS-FIT TERMINATION OPTION No
PSL
PW1
PW2
PS
0.189 (4.80)
0.512 (13.00)
0.669 (16.99)
0.236 (5.99)
Table 3
Plating Suffix
Insulator Color
Press-Fit Termiantions
Solder Tail Terminations
Plating Composition
TG30
Gray
(RIA E2 & C2 apply)
(RIA E3 & C2 apply)
0.76 μm [30 μ”] Min. Au Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
TR
Gray
(RIA E2 & C2 apply)
(RIA E3 & C2 apply)
0.08 μm [3 μ”] Min. Au Contact Area
0.18 μm [7 μ”] Min. PdNi Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
RR
Gray
(RIA E2 & C2 apply)
N/A
0.08 μm [3 μ”] Min. Au over 0.18 μm
[7 μ”] Min. PdNi Contact Area (each end)
2.54 μm [100 μ”] Min. SnPb Term. Area
1.27 μm [50 μ”] Min. Ni all over
GG30
Gray
(RIA E2 & C2 apply)
N/A
0.76 μm [30 μ”] Min. Au Contact Area (each end)
2.54 μm [100 μ”] Min. SnPb Term. Area
1.27 μm [50 μ”] Min. Ni all over
MH
Black
(RIA E1 & C1 apply)
(RIA E1 & C1 apply)
0.76 μm [30 μ”] Min. Au Contact Area
5.08 μm [200 μ”] Min. Reflowed Matte
Whisker Mitigating Sn Term. Area
1.27 μm [50 μ”] Min. Ni all over
HS
Black
(RIA E1 & C1 apply)
(RIA E1 & C1 apply)
0.08 μm [3 μ”] Min. Au over 0.18 μm
[7 μ”] Min. PdNi Contact Area
5.08 μm [200 μ”] Min. Reflowed Matte
Whisker Mitigating Sn Term. Area
1.27 μm [50 μ”] Min. Ni all over
KT
Black
(RIA E1 & C1 apply)
(RIA E1 & C1 apply)
0.25 μm [10 μ”] Min. Au Contact Area
5.08 μm [200 μ”] Min. Reflowed Matte
Whisker Mitigating Sn Term. Area
1.27 μm [50 μ”] Min. Ni all over
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
TS-1131-C
Sheet 3 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ DIN C-Form Socket
.100” Standard Mount, Vertical, Solder Tail or Press-Fit Termination DIN
41612 Series
-C-
D
E
0.012
.30
C
B
A
-B0.200
5.08
2
1
O
lO
0.100
2.54
0.100 TYP.
2.54
X
0.110
2.79
O F
0.100
2.54
PLATED THROUGH- HOLE
0.006 M A B C
lO
-A-
0.004 M A B C
RECOMMENDED MOUNTING HOLE PATTERN
HOLE PLATING TABLE For TG, TR, RR (Press-Fit Leads)
HOLE
DRILLED HOLE DIA. in (mm)
Cu THICKNESS in (mm)
SnPb THICKNESS μin (μm)
“F”
FINISHED DIA. in (mm)
0.037 - 0.043 (0.94 - 1.09)
HOLE PLATING TABLE For TG, TR, RR (Solder Tail Leads)
HOLE
DRILLED HOLE DIA. in (mm)
Cu THICKNESS in (mm)
SnPb THICKNESS μin (μm)
“F”
FINISHED DIA. in (mm)
0.041 - 0.049 (1.04 - 1.24)
HOLE PLATING TABLE For MH, HS and KT (Press-Fit Leads)
HOLE
DRILLED HOLE DIA. in (mm)
Cu THICKNESS in (mm)
Immersion Whisker Mitigating
Matte Sn Thickness μin (μm)
FINISHED DIA. in (mm)
“F”
0.0425-0.044 (1.080-1.118) #57 OR
1.10mm TWIST DRILL
0.0010 - 0.0020 (0.025 0.045)
20 - 100 (0.508 - 2.54)
0.037 - 0.043 (0.94 - 1.09)
HOLE PLATING TABLE For MH, HS, and KT (Solder Tail Leads)
HOLE
DRILLED HOLE DIA. in (mm)
“F”
Cu THICKNESS in (mm)
Immersion Matte Sn Thickness
μin (μm)
FINISHED DIA. in (mm)
0.041 - 0.049 (1.04 - 1.24)
TS-1131-C
Sheet 4 of 4
3
Electronic Solutions Division
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC, as amended by EU Commission Decision 2005/717/EC, as amended by
EU Court of Justice Decision 2008/C 116/04
This product contains decaBDE in the insulating material in excess of the maximum concentration allowed for finished
products subject to EU RoHS that are placed on the EU market after June 30, 2008.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.product Warranty stated below.
RIA-2217A-E
Appendix E5: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under
Item 6 of the Annex to the Directive.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless
the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information
represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the
product or part does not contain any of the following substances in excess of the following maximum concentration values in any
homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated
diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability and
Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain
Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or
polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
RIA-2217A-E
Appendix C3: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for
Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that
the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration
values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or
polybrominated diphenyl ethers (excluding decaBDE); or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with
3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in accordance with the
product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of 90 days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING,
BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty
period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where
prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the
legal theory asserted.
3
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3m.com/interconnects
Please recycle. Printed in USA.
© 3M 2008. All rights reserved.
RIA-2217A-E
3M is a trademark of 3M Company.